RAB Lighting LSHARK8 Operating instructions
- Type
- Operating instructions
ANGSHARK ACCESSORY INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2015 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
ANGSHARK IN 1015
TROUBLESHOOTING
1. Check that line voltage at the xture is correct. Be sure the xture is grounded properly.
2. Refer to wiring, cleaning and maintenance directions on SHARK ™ (sold separately) Installation Instructions.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
ANGSHARK INSTALLATION
1. Use appropriate mounting hardware (not supplied) to secure the Corner Bracket (2) to mounting surface as shown in Fig. 1.
Bracket Tabs must face towards each other. Recommended Corner Bracket Distance center to center is 13-5/16” (for 2 feet)
and 35-23/32” (for 4 feet).
2. Secure Snap On Bracket (2) (supplied standard with Housing) to Corner Bracket (2) with Screws provided as shown in Fig. 1.
3. Snap Housing on Snap On Brackets (2). Snap On Brackets (2) latch onto the Grooves on Lens as shown in Fig. 1 to secure
Housing. Fixture installation should look like Fig. 2 upon completion.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws and plugs inserted and
tightened rmly.
• Apply weatherproof silicone sealant around the edge of the Housing. This is especially important with an uneven
ceiling surface.
• Silicone all plugs and unused conduit entries and USE SHARK WITH CONDUIT ONLY.
• FOLLOW ALL SHARK ™ (sold separately) INSTALLATION INSTRUCTIONS
Fig. 1
Corner
Bracket (2)
Screw
Bracket Tab
Distance
Housing
Lens
Groove
Fig. 2
Mounting
Surface
Snap On
Bracket (2)
(supplied
standard w/
Housing)
CMSHARK ACCESSORY INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2015 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
CMSHARK IN 1015
TROUBLESHOOTING
1. Check that line voltage at the xture is correct. Be sure the xture is grounded properly.
2. Refer to wiring, cleaning and maintenance directions on SHARK ™ (sold separately) Installation Instructions.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws and plugs inserted and
tightened rmly.
• Apply weatherproof silicone sealant around the edge of the Housing. This is especially important with an uneven
ceiling surface.
• Silicone all plugs and unused conduit entries and USE SHARK WITH CONDUIT ONLY.
• FOLLOW ALL SHARK ™ (sold separately) INSTALLATION INSTRUCTIONS
CMSHARK INSTALLATION
1. Secure each Bracket A (2) to Housing with screws provided.
WARNING: Brackets must be mounted at exact location as shown in Fig. 1.
2. Use appropriate mounting hardware (not supplied) to secure each Bracket B (2) (Fig. 2) to mounting surface. Bracket
Distance measured center to center is 12-19/32” (for 2 feet) and 32” ( for 4 feet) (Fig. 1).
WARNING: To secure Housing, Bracket B (2) must be aligned with each other.
3. Hang one side of Bracket A onto Bracket B and tighten Screw (2) on other side as shown in Fig. 3
Fig. 3
Screw (2)
Bracket B
Bracket B
Fig. 2
Fig. 1
Bracket A
Housing
Distance
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
JBSHARK ACCESSORY INSTRUCTIONS
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2015 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
JBSHARK IN 1015
TROUBLESHOOTING
1. Check that line voltage at the xture is correct. Be sure the xture is grounded properly.
2. Refer to wiring, cleaning and maintenance directions on SHARK ™ (sold separately) Installation Instructions.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
JBSHARK INSTALLATION
1. Secure Bracket A (2) to Housing with screws provided.
WARNING: Brackets must be mounted at exact location
shown in Fig. 1.
2. Use appropriate mounting hardware (not supplied) to secure
the Junction Box Plate (Fig. 2) to Mounting Surface or
junction box (Fig. 3). Check that gasket is fully sealed. Use
Cord Grip provided with xture to feed supply wires in xture.
3. Hang one side of each Bracket A onto Junction Box Plate
and tighten Screws (2) on other side as shown in Fig. 3.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws and plugs inserted and
tightened rmly.
• Apply weatherproof silicone sealant around the edge of the Housing. This is especially important with an uneven
ceiling surface.
• Silicone all plugs and unused conduit entries and USE SHARK WITH CONDUIT ONLY.
• FOLLOW ALL SHARK ™ (sold separately) INSTALLATION INSTRUCTIONS
Fig. 1
Housing
Bracket A (2)
Fig. 2
Junction Box Plate
Fig. 3
Mounting
Surface
Junction
Box Plate
Bracket A (2)
Screw (2)
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
VHOOKSHARK ACCESSORY INSTRUCTIONS
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2015 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
VHOOKSHARK IN 1015
TROUBLESHOOTING
1. Check that line voltage at the xture is correct. Be sure the xture is grounded properly.
2. Refer to wiring, cleaning and maintenance directions on SHARK ™ (sold separately) Installation Instructions.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
VHOOKSHARK INSTALLATION
1. Secure Bracket A (2) to Housing with screws provided.
WARNING: Brackets must be mounted at exact location shown in Fig. 1.
2. Loop each V-Hook (2) on Bracket A as shown in Fig. 2. Fixture should
look like Fig. 3 when nished with step 2.
3. To suspend Housing, connect each V-Hook to two (2) equal lengths of
chain (not supplied) and/ or appropriate hardware (by others) suitable
for mounting surface. Use chain suitable to support four (4) times the
weight of the xture.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws and plugs inserted and
tightened rmly.
• Apply weatherproof silicone sealant around the edge of the Housing. This is especially important with an uneven
ceiling surface.
• Silicone all plugs and unused conduit entries and USE SHARK WITH CONDUIT ONLY.
• FOLLOW ALL SHARK ™ (sold separately) INSTALLATION INSTRUCTIONS
Fig. 1
Bracket A
Housing
Distance
V-Hook (2)
Bracket A (2)
Fig. 2
Fig. 3
Bracket A (2)
V-Hook (2)
Housing
TPKSHARK SHARK
TAMPERPROOF BRACKETS
TPKSHARK SHARK
TAMPERPROOF BRACKETS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000,
or email: marketing@rabweb.com
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000,
or email: marketing@rabweb.com
TM
TM
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code
and all applicable local codes. Proper grounding is required for safety. This
product must be installed in accordance with the applicable installation code
by a person familiar with the construction and operation of the product and
the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining
xture.
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be sure xture temperature is cool enough to touch. Do not
clean or maintain while xture is energized.
TPKSHARK 6/16
Note: These instructions do not cover all details or variations in equipment nor do
they provide for every possible situation during installation, operation or maintenance.
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2016 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
TPKSHARK 0616
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2016 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code
and all applicable local codes. Proper grounding is required for safety. This
product must be installed in accordance with the applicable installation code
by a person familiar with the construction and operation of the product and
the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining
xture.
CLEANING
Clean glass lens with nonabrasive glass cleaning solution.
CAUTION: Be sure xture temperature is cool enough to touch. Do not
clean or maintain while xture is energized.
Note: These instructions do not cover all details or variations in equipment nor do
they provide for every possible situation during installation, operation or maintenance.
Housing
Latch
TAMPERPROOF BRACKET MOUNT
1. The tamperproof brackets (4 in each kit) can be installed on already
installed Housing without opening the Housing.
2. The tamperproof bracket mounts to existing holes on the Housing
between the Latch (as shown in g).
3. Clip the bracket on the lens. Secure the bracket with provided screws (2
for each bracket) using star head T20 drive.
Tamperproof
screws (2)
bracket
Housing
Latch
TAMPERPROOF BRACKET MOUNT
1. The tamperproof brackets (4 in each kit) can be installed on already
installed Housing without opening the Housing.
2. The tamperproof bracket mounts to existing holes on the Housing
between the Latch (as shown in g).
3. Clip the bracket on the lens. Secure the bracket with provided screws (2
for each bracket) using star head T20 drive.
Tamperproof
screws (2)
bracket
-
1
-
2
-
3
-
4
-
5
RAB Lighting LSHARK8 Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
RAB Lighting ALED150HSW Operating instructions
-
RAB Lighting LALED78W Operating instructions
-
-
-
-
-
-
RAB Lighting SHARK2-25YNW/480/D10 Operating instructions
-
-