Serious Steel
920101
INCLINE PRESS BENCH-
ASSEMBLY INSTRUCTIONS
ParaBody, Ncorporated
14150 Sunfish Lake Boulevard
Ramsey, MN 55303
1-800-328-9714
Part# 6626501
1 Revision: 06/04/96
920101 INCLINE PRESS BENCH ASSEMBLY PARTS LIST
SORT ANGD COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY
HARDWARE:
ITEM
NAME/DESCRIPTION
QTY
2.
3.
4.
5.
6.
7.
8.
9.
1/2 X 3 IN BOLT ...............................................................................................................
4
3/8 X 2-3/4 IN BOLT .........................................................................................................
5
1/2 IN WASI-IER ................................................................................................................
4
3/8 IN WAS,HER ................................................................................... : ............................
5
1/2 IN LOCK NUT .............................................................................................................
4
SPRING PIN ......................................................................................................................
1
3 X 2 IN END CAP ............................................................................................................
2
1-3/4 ~ SQ E~ C~ .......................................................................................................
1
1-I/2 X 3/4 :~ GL~E (8 PER) ..........................................................................................
1
WELDMENTSfPARTS:
ITEM NAME/DESCRIPTION
2.
3.
4.
5.
UPRIGHT iFRAME WELDMENT ............................
(6614403) .....................................
I
BENCH F1]AME WELDMENT ................................
(6614503) ..................................... 1
SEAT SUPPORT WELDMENT ................................ (6614602) .....................................
SEAT PAD ................................................................ (66186XX) .....................................
1
BACK PAD ...............................................................
(66185XX) ..................................... 1
NOTE: BOLT LENGT]I:i" IS MEASURED FROM THE UNDERSI~E OF THE ~AD OF TBg BOLT.
i!!!!!!!l
BOLT I.,t’,NG’I’It " I
BOLT LENGTH RULER:
0
1 2 3 4 -5
6
Part # 6626501 2
Revision: 06/04/96
920101 INCLINE PRESS BENCH ASSEMBLY INSTRUCTIONS
............. ~ .............................< ........................
.....~.~,, ..................
~<,<<,,., ~.~.~ ............
. ...........
~ ..................~.,..~..~ .........
~ ~.~.
: :::::~: ~:~:~ :~::::~::~:: :::~:: :~ :~ :~:~$~: :~:~:[:~:::~:~:::~::::~:~:~:~::~ :....:.-.-.:.:..:.;..-.-.-.-.:......-.-.-:.-.-:.....,-...-......:.......:,-:.:... -:.:-:- -.- -.. .................................’-’.. -:-’.:~::~:.~::~<~<s~,’:~:~?~::~ ~ " ""
~;~:~:.~.~.~.~.~.~.~.~.~.~.~:.~.~.~.~.~.~.~:.~.~.~.~.~.~.~.~.~.~.~:.~:.>~.~.~.~:.~.>>~.~.~.~.~.~.~
~:.:.~::~ ~::-:~" ’.’-:: ~.:.’.:~ ".’.’::.’ "~...’.-~ :~ ...........
<......~’~.-.’....::..-:~ ............~ ...........:~ ..........::.. ¯ ..-:::-,4 .............~;::: .............................~ ...........~ .......................~,~-.:~-.:<~>~:.~~:.,~::~
~
.~::~:::::::~:: ~::~::::~::~:~ ~:g~i:~{!:~::
~
~:~:~:~:.~---.-.-.~-.,-.,:.,’.:.~,-.~. ~, ,..~-...-.~,, ,........ ~ ~..~.., ,:.,....~....... ~,~.,-.,:.:::....- ~ ~.~<.~.:~<~:~..~:::~ .~ .:~’~.¢<,,.¢~<-...-.....~-.-...>~,,>.. -...,...<..,, ~....~:<..,~ ¯., <<~ ~-.....:..~ ..........~,.:~ ., -...,, >~. < .. ~..
::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::: :::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::: =================~=======~~=========~~=~~=~=~~=~=~~=~~=~ ~:~:~:~:~:::~:~:~:~:~:~:~:~;~:::~:~::~:~:~:~:~:~:~:~:~:~:~:~:~:~:~:~:?~::~:::::~:~::::::::: ~:,::::~::: ::~::: ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::: :~: :: :~.~:.:,s:::.: ~,
I
~’’’’’’’’-’’’’’-’’’’" ""
" "’:’ " "" :" :" :" :-:" :" :’:: :" ~" :" :" :" i" :"
:<"
:" :<’." :’.’.’. ." ’.’:. ".’. ".’.’.’. ".’.’. ".’.’.’." :’.’.’.’.’:. "::::. ~’.’.’." "."-’. ".’.’.’. ":.’.’~ ".’:.’.’.’.’. ".’. ,’-’-’-’. ".y.’~ ~’." :,"" ".’:." ’." ". ,’-’. ".-." "::.’.’.’ :-y.-:-:... :-..... <...::...-:..:.-.-:.-: i’: ;" ?r ? :’:~ ": ;" :" :" :’" "" :’ :’ :" :’i
~’"
:’: :" :" :" :" :" :" :" :~ ~" :’:~ ~ ~ ~" :~ ~ ~ $ ~ ~ ]
SECURELY assemble the BENCH FRAME WELDMENT to the UPRIGHT FRAME WELDMENT
as shown on drawing.
Attach eight (8) 1-1/2 X 3/4 IN GLIDES to the SLEEVE TUBE on the BENCH FRAME
WELDMENT as shown in DETAIL B.
SECURELY assemble the SPRING PIN to the SPRING PIN HOUSING of the SLEEVE TU]~E as
shown in DETAIL A.
¯.
Insert two (2) 3 X 2 IN END CAPS, and one (1) I-3/4 IN SQ END CAP into the ends or:the
SUPPORT WELDMENT as shown on drawing.
5.
SECURELY assemble the SEAT PAD to the SEAT SUPPORT WELDMENT as shown on drawing.
Pull back the SPR~ING PIN on the SLEEVE TUBE of the BENCH FRAME WELDMENT a~.d insert
the SEAT SUPPORT WELDMENT. Release the SPRING PIN into the desired hole.
SECURELY assemble the BACK PAD to the UPRIGHT FRAME, and BENCH FRAME
WELDMENTS as shown on drawing.
Part# 6626501
Revision: 06/04/96
z
Z
0
Z
/
