2. American Standard
  3. 0056001.020

American Standard 0056001.020 Specification

  • Hello! I am an AI chatbot trained to assist you with the American Standard 0056001.020 Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
J93
© 2018 AS America Inc.
spec_0297800 Town Square S ped sink 4/18
TOWN SQUARE
®
S
PEDESTAL SINK
FINE FIRECLAY
TOWN SQUARE
®
S PEDESTAL SINK
Pedestal Sink and Leg Combinations:
❏ 0297800 Faucet holes on 8" (203mm) centers
❏ 0297100 Center hole only
•Finereclay
•Classicstyledrectangularpedestallavatory
•Rearoverow
•Suppliedwithmountingkit
•RightHeight
®
forgreatercomfortduringuse
•Faucetledgewithlargedeckarea(faucetnotincluded)
•DesigncoordinateswithTownSquare
®
S Fixtures
and Faucets
•PedestaltopscanalsobeusedwithMetalConsoleTable
Nominal Dimensions:
30" x 22-1/2" x 35"
(761 x 571 x 889 mm)
❏ 0297008Pedestaltop-8"(203mm)centers
❏ 0297001 Pedestaltop-centerholeonly
❏ 0056001Pedestallegonly
❏ 8721000Consoletable
❏ 7720018Optionaldecorativep-trapdrain
Bowl size:
17-1/2" (445mm) wide,
12-1/4"(311mm)fronttoback,
5-1/4" (133mm) deep
Compliance Certications -
Meets or Exceeds the Following Specications:
•ASMEA112.19.2/CSAB45.1
To Be Specied:
❏ Color: ❏ White ❏ Linen
❏ Console Finish: ❏ Chrome ❏BrushedNickel
❏ Faucet:*
❏ Supplies:
❏ P-Trap:❏ Chrome ❏BrushedNickel
*SeeTownSquareSfaucetsectionformodelsavailable
SEEREVERSEFORROUGHING-INDIMENSIONS
Town Square S pedestal
combination 0297800
Town Square S pedestal top
sink 0297008 shown with
8721000 console table
J94
© 2018 AS America Inc.
spec_0297800 Town Square S ped sink 4/18
TOWN SQUARE
®
S
PEDESTAL SINK
FINE FIRECLAY
NOTES:
*
DIMENSIONSSHOWNFORLOCATIONOFSUPPLIESAND“P"TRAPSARESUGGESTED.
■SUITABLEFORREINFORCEMENTONLY.ACTUALDIMENSIONSMUSTBETAKENFROMFIXTURE.
FITTINGNOTINCLUDEDANDMUSTBEORDEREDSEPARATELY.
PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORTS.
INSTALLATIONINSTRUCTIONSSUPPLIEDWITHLAVATORY.
IMPORTANT:DimensionsofxturesarenominalandmayvarywithintherangeoftoleranceestablishedbyANSIStandardA112.19.2
Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibility isassumedforuseofsupersededorvoidedpages.
SUPPLY
AS REQ'D
1-1/4" O.D.
WASTE
1-1/4" O.D.
TAILPIECE
SUPPLY
AS
REQ'D
8-5/8"
(220 mm)
2-3/4"
(70 mm)
22-1/2"
(571 mm)
30"
(761 mm)
FAUCET MOUNTING HOLES:
SINGLE HOLE OR 8" (203 mm)
9-1/2"
(240 mm)
*
22-3/4"
(578 mm)
*
20-1/2"
(521 mm)
35"
(889 mm)
*
8"
(203 mm)
29"
(736 mm)
■
2-3/8"
(60 mm)
9/16"
(15 mm)
35"
(889 mm)
34-3/8"
(874 mm)
6-1/2"
(165 mm)
■
2-3/8"
(60 mm)
24-1/2"
(621 mm)
22-1/2"
(571 mm)
9-1/8"
(231 mm)
18-5/8"
(473 mm)
■ 7-1/4" (185 mm)
FOR ANCHOR
SCREW MOUNT
■ 7-1/4" (185 mm) FOR
ANCHOR SCREW MOUNT
*
8"
(203 mm)
*
20-1/2"
(521 mm)
*
22-3/4"
(578 mm)
5-1/2"
(140mm)
640mm
(25-1/4")
*
20-1/2"
(521 mm)
PEDESTAL SINK
TOP VIEW
PEDESTAL SINK
WITH LEG
PEDESTAL SINK WITH CONSOLE
/