2. American Standard
  3. 8719000.295
8719000.295

American Standard 8719000.295 User manual

  • Hello! I am an AI chatbot trained to assist you with the American Standard 8719000.295 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
J25
© 2017 AS America Inc.
spec_0445EdgmerePedSink4/17
EDGEMERE
®
PEDESTAL SINK
FINE FIRECLAY
EDGEMERE
®
PEDESTAL SINK
❏ 0445.800 Faucet holes on 8" (203mm) centers
❏ 0445.400 Faucet holes on 4" (102mm) centers
❏ 0445.100 Center hole only
•Finereclay
•Classicstyledrectangularpedestallavatory
•Rearoverow
•Suppliedwithmountingkit
•RightHeight
®
forgreatercomfortduringuse
•Faucetledgewithlargedeckarea(faucetnotincluded)
•Design coordinates with Edgemere
®
Fixtures and Faucets
•PedestaltopscanalsobeusedwithEdgemereConsoleTable
Nominal Dimensions:
25" x 19-1/2" x 35-5/8"
(635 x 495 x 905mm)
❏ 0445.008 Pedestal top-8" (203mm) centers
❏ 0445.004 Pedestal top-4" (102mm) centers
❏ 0445.001 Pedestal top-center hole only
❏ 0039.000 Pedestal only
❏ 8719.000 Console table
❏ 7720.018Optionaldecorativep-trapdrain(notshown)
Bowl sizes:
17-1/8" (435mm) wide,
12" (305mm) front to back,
5-1/4" (133mm) deep
Compliance Certications -
Meets or Exceeds the Following Specications:
•ASMEA112.19.2/CSAB45.1
To Be Specied:
❏ Color: ❏ White
❏ Console Finish: ❏ Chrome ❏BrushedNickel
❏ Faucet Finish:
❏ Supplies:
❏ P-Trap: ❏ Chrome ❏BrushedNickel
❏ Nipple:
*Seefaucetsectionforadditionalmodelsavailable
SEEREVERSEFORROUGHING-INDIMENSIONS
J26
© 2017 AS America Inc.
spec_0445EdgmerePedSink4/17
EDGEMERE
®
PEDESTAL SINK
FINE FIRECLAY
OPEN TO
FLOOR
FINISHED WALL
OR BACKSPLASH
SUPPLIES
AS REQ'D
1-1/4" O.D.
WASTE
1-1/4" O.D.
TAILPIECE
FINISHED
FLOOR
*22-3/4"
(578mm)
*20-1/2"
(521mm)
8"
(202mm)
8-3/8"
(213mm)
7/8"
(22mm)
2X HOLES FOR
ANCHOR BOLTS
FAUCET MOUNTING HOLES:
SINGLE HOLE, 4" (102mm)
OR 8" (203mm)
8-1/2"
(215mm)
25"
(635mm)
19-1/2"
(495mm)
DRAIN CHASE
2"
(50mm)
8"
(203mm)
35-5/8"
(905mm)
FINISHED
FLOOR
FINISHED
WALL
FINISHED
WALL
35-11/16"
(906mm)
19-1/2"
(495mm)
4-7/16"
(112mm)
6-5/16"
(160mm)
1-9/16"
(40mm)
21-1/2"
(545mm)
8-3/8"
(213mm)
30-1/2"
(775mm)
28"
(710mm)
34-1/16"
(866mm)
8-1/8"
(207mm)
24-1/2"
(622mm)
25"
(635mm)
17-1/2"
(444mm)
20-1/4"
(514mm)
5-1/2"
(140mm)
FAUCET MOUNTING HOLES:
SINGLE HOLE, 4" (102mm)
OR 8" (203mm)
2X HOLES FOR
ANCHOR BOLTS
NOTES:
*
DIMENSIONSSHOWNFORLOCATIONOFSUPPLIESAND“P"TRAPSARESUGGESTED.
▼ PEDESTALANCHORINGSCREWSNOTINCLUDED.
■SUITABLEFORREINFORCEMENTONLY.ACTUALDIMENSIONSMUSTBETAKENFROMFIXTURE.
FITTINGNOTINCLUDEDANDMUSTBEORDEREDSEPARATELY.
PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORTS.
INSTALLATIONINSTRUCTIONSSUPPLIEDWITHLAVATORY.
IMPORTANT:DimensionsofxturesarenominalandmayvarywithintherangeoftoleranceestablishedbyANSIStandardA112.19.2
Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibility isassumedforuseofsupersededorvoidedpages.
PEDESTAL CONFIGURATIONS METAL CONSOLE CONFIGURATIONS
/