American Standard 0056001.222 Specification

Brand: American Standard

Model: 0056001.222

Type: Specification

J93

spec_0297800 Town Square S ped sink 4/18

TOWN SQUARE

PEDESTAL SINK

FINE FIRECLAY

TOWN SQUARE

S PEDESTAL SINK

Pedestal Sink and Leg Combinations:

❏ 0297800 Faucet holes on 8" (203mm) centers

❏ 0297100 Center hole only

 •Finereclay

 •Classicstyledrectangularpedestallavatory

 •Rearoverow

 •Suppliedwithmountingkit

 •RightHeight

forgreatercomfortduringuse

 •Faucetledgewithlargedeckarea(faucetnotincluded)

 •DesigncoordinateswithTownSquare

S Fixtures

and Faucets

 •PedestaltopscanalsobeusedwithMetalConsoleTable

Nominal Dimensions:

30" x 22-1/2" x 35"

(761 x 571 x 889 mm)

❏ 0297008Pedestaltop-8"(203mm)centers

❏ 0297001 Pedestaltop-centerholeonly

❏ 0056001Pedestallegonly

❏ 8721000Consoletable

❏ 7720018Optionaldecorativep-trapdrain

Bowl size:

17-1/2" (445mm) wide,

12-1/4"(311mm)fronttoback,

5-1/4" (133mm) deep

Compliance Certications -

Meets or Exceeds the Following Specications:

•ASMEA112.19.2/CSAB45.1

To Be Specied:

❏ Color: ❏ White ❏ Linen

❏ Console Finish: ❏ Chrome ❏BrushedNickel

❏ Faucet:*

❏ Supplies:

❏ P-Trap:❏ Chrome ❏BrushedNickel

*SeeTownSquareSfaucetsectionformodelsavailable

SEEREVERSEFORROUGHING-INDIMENSIONS

Town Square S pedestal

combination 0297800

Town Square S pedestal top

sink 0297008 shown with

8721000 console table

J94

spec_0297800 Town Square S ped sink 4/18

TOWN SQUARE

PEDESTAL SINK

FINE FIRECLAY

NOTES:

DIMENSIONSSHOWNFORLOCATIONOFSUPPLIESAND“P"TRAPSARESUGGESTED.

■SUITABLEFORREINFORCEMENTONLY.ACTUALDIMENSIONSMUSTBETAKENFROMFIXTURE.

FITTINGNOTINCLUDEDANDMUSTBEORDEREDSEPARATELY.

PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORTS.

INSTALLATIONINSTRUCTIONSSUPPLIEDWITHLAVATORY.

IMPORTANT:DimensionsofxturesarenominalandmayvarywithintherangeoftoleranceestablishedbyANSIStandardA112.19.2

Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibility isassumedforuseofsupersededorvoidedpages.

SUPPLY

AS REQ'D

1-1/4" O.D.

WASTE

1-1/4" O.D.

TAILPIECE

SUPPLY

REQ'D

8-5/8"

(220 mm)

2-3/4"

(70 mm)

22-1/2"

(571 mm)

30"

(761 mm)

FAUCET MOUNTING HOLES:

SINGLE HOLE OR 8" (203 mm)

9-1/2"

(240 mm)

22-3/4"

(578 mm)

20-1/2"

(521 mm)

35"

(889 mm)

(203 mm)

29"

(736 mm)

■

2-3/8"

(60 mm)

9/16"

(15 mm)

35"

(889 mm)

34-3/8"

(874 mm)

6-1/2"

(165 mm)

■

2-3/8"

(60 mm)

24-1/2"

(621 mm)

22-1/2"

(571 mm)

9-1/8"

(231 mm)

18-5/8"

(473 mm)

■ 7-1/4" (185 mm)

FOR ANCHOR

SCREW MOUNT

■ 7-1/4" (185 mm) FOR

ANCHOR SCREW MOUNT

(203 mm)

20-1/2"

(521 mm)

22-3/4"

(578 mm)

5-1/2"

(140mm)

640mm

(25-1/4")

20-1/2"

(521 mm)

PEDESTAL SINK

TOP VIEW

PEDESTAL SINK

WITH LEG

PEDESTAL SINK WITH CONSOLE

American Standard 0056001.222 Specification

American Standard 0056001.222 Specification

American Standard 0056001.222 Specification

Related papers

Other documents