Extron RWM 1 User manual

Brand: Extron

Model: RWM 1

Type: User manual

Extron RWM 1 is an accessory kit for the TLP Pro 525M touchpanel to be installed into a wall. It provides a secure and professional way to mount your touchpanel in various locations, such as classrooms, conference rooms, and home theaters.

The RWM 1 is suitable for drywall that is 1/2-1" (13-25mm) thick. It comes with three magnets attached to the front and a spare magnet that can be moved to the front if extra support is needed. The strong magnets on the RWM 1 hold the touchpanel in place, making it easy to install and remove.

RWM 1 • Installation Guide

Overview

The RWM 1 is an accessory kit for the TLP Pro 525M touchpanel

to be installed into a wall. This guide provides instructions for

experienced and professional installers to mount and install the TLP

Pro 525M using an RWM 1.

ATTENTION:

• All structural steps and electrical installation must be performed by qualified personnel in accordance with local

and national building codes and electrical codes.

• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualifié, conformément aux

codes du bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.

Figure 1. RWM 1

A Screws to turn locking arm (4) C 2-gang EU junction box mounting

holes

E 1-gang North America

junction box mounting holes,

horizontally mounted

B Magnets (4) D 1-gang MK junction box mounting

holes

F Locking arms (4)

The RWM 1 ships with three magnets attached to the front and a spare magnet (

) attached to the back, as shown in

figure 1. The spare magnet can be moved to the front if extra support is needed.

TOP

NORTH

AMERICA

NORTH

AMERICA

Front View Back View

IMPORTANT:

Go to www.extron.com for the

complete user guide and installation

instructions befor

e connecting the

oduct to the power sou

rce.

www.extron.com

RWM 1

TLP Pro 525M

Mounted Touchpanel

RWM 1 • Installation Guide (Continued)

Figure 3. Installing the TLP Pro 525M

Before You Start

Decide where you want to mount the touchpanel. A

cut-out template for the RWM 1 is available at www.

extron.com and it provides clearances for the com-

ponents to be installed.

1. Use the template to cut a hole in the drywall

or furniture (see figure 2,

) that is 4.15'' H x

6.07'' W (105 mm H x 154 mm W). The RWM

1 is suitable for drywall that is 1/2-1'' (13-

25mm) thick.

2. Route cables to the hole.

If local building codes require cables to be run through

a conduit to a junction box, then the RWM 1 can be

used with a standard 2-gang EU junction box, 1-gang

MK junction box, or a horizontally mounted 1-gang US

junction box (Extron JB 125). The junction box must be

purchased separately.

If required, attach the junction box to the RWM 1 using

the screws provided with the junction box through the

corresponding holes in the RWM 1 (see Figure 1).

68-3269-01 Rev. B

11 18

Mounting the RWM 1 to Drywall

1. Ensure the locking arms (

) are lying flat against the top and bot-

tom of the RWM 1, and insert the RWM 1 into the hole.

2. Use a Philips-head screwdriver to turn and tighten the locking

arms against the drywall. The locking arms should hold the RWM 1

securely, but should not be overtightened.

The cables have to come through the RWM 1 opening before

inserting the RWM 1 onto the wall and tightening the locking

arms.

RWM 1

Touchpanel

Mounting

Plate

Lock Screw

Back View

TLP Pr

o 525M

Figure 2. Installing RWM 1 into the wall

Mounting the TLP Pro 525M

1. Run a PoE/Ethernet cable through the RWM 1 and

connect it to the rear panel port on the touchpanel

(see the TLP Pro 525, 725, and 1025 Series User

Guide)

2. The touchpanel mounting plate has two hooks (

)

located on the top left and right corners. Position the

TLP Pro 525M so the hooks fit into the two rear slots

of the touchpanel (see the TLP Pro 525 Series, 725

Series, and 1025 Series User Guide).

3. Slide the TLP Pro 525M down slightly so the hooks

are secure in the slots.

4. The tongue at the bottom of the mounting plate (

)

sits in the groove at the bottom of the touchpanel

(

). Fasten the touchpanel to the mounting plate by

tightening the lock screw (

5. Place the touchpanel against the RWM 1. Strong

magnets on the RWM 1 hold the touchpanel in

place.

NOTE: The cables have to come through the RWM 1 opening before

inserting the RWM 1 onto the wall and tightening the locking

arms.

RWM 1

TLP Pr

o 525M

Wall

Side View

Mounted Touchpanel Side View

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

Extron RWM 1 User manual

Extron RWM 1 User manual

Related papers

Other documents