RWM 1 • Installation Guide
Overview
The RWM 1 is an accessory kit for the TLP Pro 525M touchpanel
to be installed into a wall. This guide provides instructions for
experienced and professional installers to mount and install the TLP
Pro 525M using an RWM 1.
ATTENTION:
• All structural steps and electrical installation must be performed by qualified personnel in accordance with local
and national building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualifié, conformément aux
codes du bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
Figure 1. RWM 1
1
A Screws to turn locking arm (4) C 2-gang EU junction box mounting
holes
E 1-gang North America
junction box mounting holes,
horizontally mounted
B Magnets (4) D 1-gang MK junction box mounting
holes
F Locking arms (4)
The RWM 1 ships with three magnets attached to the front and a spare magnet (
G
) attached to the back, as shown in
figure 1. The spare magnet can be moved to the front if extra support is needed.
TOP
NORTH
AMERICA
EU
MK
EU
NORTH
AMERICA
EU
MK
EU
Front View Back View
FF
BB
C
C
D
D
EE
AA
GG
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions befor
e connecting the
pr
oduct to the power sou
rce.
www.extron.com
e
RWM 1
TLP Pro 525M
Mounted Touchpanel
RWM 1 • Installation Guide (Continued)
Figure 3. Installing the TLP Pro 525M
Before You Start
Decide where you want to mount the touchpanel. A
cut-out template for the RWM 1 is available at www.
extron.com and it provides clearances for the com-
ponents to be installed.
1. Use the template to cut a hole in the drywall
or furniture (see figure 2,
1
) that is 4.15'' H x
6.07'' W (105 mm H x 154 mm W). The RWM
1 is suitable for drywall that is 1/2-1'' (13-
25mm) thick.
2. Route cables to the hole.
If local building codes require cables to be run through
a conduit to a junction box, then the RWM 1 can be
used with a standard 2-gang EU junction box, 1-gang
MK junction box, or a horizontally mounted 1-gang US
junction box (Extron JB 125). The junction box must be
purchased separately.
If required, attach the junction box to the RWM 1 using
the screws provided with the junction box through the
corresponding holes in the RWM 1 (see Figure 1).
2
68-3269-01 Rev. B
11 18
Mounting the RWM 1 to Drywall
1. Ensure the locking arms (
2
) are lying flat against the top and bot-
tom of the RWM 1, and insert the RWM 1 into the hole.
2. Use a Philips-head screwdriver to turn and tighten the locking
arms against the drywall. The locking arms should hold the RWM 1
securely, but should not be overtightened.
The cables have to come through the RWM 1 opening before
inserting the RWM 1 onto the wall and tightening the locking
arms.
11
RWM 1
22
e
33
5
5
RWM 1
Touchpanel
Mounting
Plate
Lock Screw
Back View
TLP Pr
o 525M
66
44
Figure 2. Installing RWM 1 into the wall
Mounting the TLP Pro 525M
1. Run a PoE/Ethernet cable through the RWM 1 and
connect it to the rear panel port on the touchpanel
(see the TLP Pro 525, 725, and 1025 Series User
Guide)
2. The touchpanel mounting plate has two hooks (
3
)
located on the top left and right corners. Position the
TLP Pro 525M so the hooks fit into the two rear slots
of the touchpanel (see the TLP Pro 525 Series, 725
Series, and 1025 Series User Guide).
3. Slide the TLP Pro 525M down slightly so the hooks
are secure in the slots.
4. The tongue at the bottom of the mounting plate (
4
)
sits in the groove at the bottom of the touchpanel
(
5
). Fasten the touchpanel to the mounting plate by
tightening the lock screw (
6
).
5. Place the touchpanel against the RWM 1. Strong
magnets on the RWM 1 hold the touchpanel in
place.
NOTE: The cables have to come through the RWM 1 opening before
inserting the RWM 1 onto the wall and tightening the locking
arms.
RWM 1
TLP Pr
o 525M
Wall
Wall
Side View
Mounted Touchpanel Side View
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2018 Extron Electronics. All rights reserved. www.extron.com
/
