2. Crosley
  3. CO7221-WB
CO7221-WB

Crosley CO7221-WB, KO70045WB-NV, KO70045WB-SA, KO70045WB-SG Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Crosley CO7221-WB Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Bradenton Outdoor Wicker Bar
CO7221
PART LIST
A
B
C
HARDWARE LIST
EXTRA HARDWARE LIST
D E
F
# 1
# 2 # 3
Short Bolt
12 PCS
M6*40mm
Long
6 PCS
Bolt
M6*65mm
# 4
Nut
6 PCS
Washer
24 PCS
M6mmM6mm
Wicker Top
1 PC
Center Panel
1 PC
Left Side Panel
1 PC
R
1 PC
ight Side Panel
# 5
# 6
# 7
Allen Key
1 PC
Adjustable Leveler
4 PCS
M6mm
Wrench
1 PC
M6mm M6mm
# 1
# 2 # 3
Short Bolt
3 PCS
M6*40mm
Long
1 PC
Bolt
M6*65mm
# 4
Nut
2 PCS
Washer
3 PCS
M6mmM6mm
# 7
Adjustable Leveler
1 PC
M6mm
Wicker Shelf
2 PCS
Glass Top
1 PC
2
#1
x2
#3
x2
#5
x1
#1
#3
#5
Step 2.Attach left side panel (part #C) and right side panel (part #D) to assembled parts
(part #A&B) using short bolts (part #1),long boltsl (part #2), washers (part #3),nut
(part #4) and allen key (part #5).
NOTE:Please do not fully tighten bolts until unit is fully assembled.
Step 1.Lay wicker top (part #A) on a flat surface with underside facing up.Attach center panel
(part #B) to wicker top (part #A) using short bolts (part #1), washers (part #3) and allen
key (part #5).
NOTE:Please do not fully tighten bolts until unit is fully assembled.
#1
#3
#5
#2
#5
#3
#3
#4
#6
A
B
A
B
C
D
#1
x2
#3
x14
#4
x6
#2
x6
#5
x1
#6
x1
3
#1
x4
#3
x4
#5
x1
Step 4.Attach another shelf (part #E) to assembled parts (part #B,C&D) using short bolts
(part #1), washers (part #3) and allen key (part #5).
NOTE: Please fully tighten all bolts at this time.
Step 3.Attach one shelf (part #E) to assembled parts (part #B,C&D) using short bolts
(part #1), washers (part #3) and allen key (part #5).
NOTE:Please do not fully tighten bolts until unit is fully assembled.
#1
#3
#5
#1
#3
#5
#1
x4
#3
x4
#5
x1
E
B
C
D
B
E
C
D
4
Step 5.
position on the bottom of the bar.
Screw the adjustable levelers (part #7) into the pre-drilled holes to the desired
Step 6.Carefully turn the bar upright and place the glass (part #F) on the bar top.
#7
x4
#7
F
5
/