Troy-Bilt 31AH55Q5711 Fast Start Guide

Type
Fast Start Guide

Troy-Bilt 31AH55Q5711 is a snow thrower that can help you to clear snow from your driveway, sidewalk, or other areas around your home. It has a 24-inch clearing width and a 20-inch intake height, which makes it ideal for smaller to medium-sized areas. The snow thrower is powered by a 179cc engine and has a throw distance of up to 35 feet. It also features a chute control that allows you to change the direction of the snow discharge, and a skid shoe that helps to protect the unit from damage.

Troy-Bilt 31AH55Q5711 is a snow thrower that can help you to clear snow from your driveway, sidewalk, or other areas around your home. It has a 24-inch clearing width and a 20-inch intake height, which makes it ideal for smaller to medium-sized areas. The snow thrower is powered by a 179cc engine and has a throw distance of up to 35 feet. It also features a chute control that allows you to change the direction of the snow discharge, and a skid shoe that helps to protect the unit from damage.

Upper Handle
Shift Lever
Chute Control
Hex Rod
778 -11823C© 2010 31AH55Q5
Chute
Handle Knobs
Chute Base
Chute Support
Bracket
Chute Control
Head
Place shift lever into F6 A.
position.
Pivot upper handle B.
into operating
position
Tighten handle knobs.C.
A
B
C
A
B
Remove cotter pin, wing nut and hex A.
screw from chute control head.
Remove clevis pin B.
and bow-tie
pin from chute
support bracket.
Insert the round end of the hex rod
(hole pointing upward) as far as
possible into the chute control head.
Squeeze the trigger
on the joystick and rotate
the chute (by hand)
to face forward.
The holes in the rear
of the chute control head
will be facing up.
Rotate the chute
control to 1 oclock,
so the silver arrow
on the pinion gear faces
upward.
Secure the round end of the hex
rod to the chute control head with
the cotter pin removed in Step 2.
Secure the chute control head
to the support bracket with the
remaining hardware removed
in Step 2.
Insert the hex end of the rod
(hole pointing upward)
into the pinion gear.
Place chute onto chute
base with the hex rod
positioned beneath the
handle panel.
Reinstall the hex bolt
removed in Step 2 but
do not secure with wing
nut at this time.
1
4
2
5
3
6
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
Oil Fill /
Dipstick
Electric Starter
Button
Electric
Starter Outlet
Primer
Key
Throttle
Control
Choke
Control
Gas Fill
Move throttle control into
the Fast
position.
Move the choke control
into the Choke
position.
Connect power cord to A.
electric starter outlet.
Plug other end of power B.
cord into a three-prong
120-volt, grounded, AC
receptacle.
Push primer
three times.
Fill fuel tank with clean,
fresh gasoline. Do not fill
above the base of fuel
tank neck.
Check the oil level using
the dipstick. Add oil if
necessary. (Refer to the
Operator’s Manual)
Insert the key into
the key switch until
the key snaps into
place.
Do not turn the key!
To start engine, push A.
the starter button.
When engine starts, B.
slowly move choke
control into the Run
position.
Disconnect cord from C.
power receptacle
first and then from
snow thrower’s
outlet.
778 -11823C© 2010 31AH55Q5
7
10
8
11
9
12
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
  • Page 1 1
  • Page 2 2

Troy-Bilt 31AH55Q5711 Fast Start Guide

Type
Fast Start Guide

Troy-Bilt 31AH55Q5711 is a snow thrower that can help you to clear snow from your driveway, sidewalk, or other areas around your home. It has a 24-inch clearing width and a 20-inch intake height, which makes it ideal for smaller to medium-sized areas. The snow thrower is powered by a 179cc engine and has a throw distance of up to 35 feet. It also features a chute control that allows you to change the direction of the snow discharge, and a skid shoe that helps to protect the unit from damage.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI