Furuno GP-1850DF User manual

INSTALLATION MANUAL

COLOR DGPS/PLOTTER/SOUNDER

GP-1850DF

COLOR GPS/PLOTTER/SOUNDER

GP-1850F

Safety Instructions for the Installer .......................i

Equipment Lists .....................................................ii

System Configuration ...........................................iv

1. Installation of Standard Equipment ...............1-1

1.1 Installation of Display Unit ..............................................1-1

1.2 Installation of Antenna Unit .............................................1-3

1.3 Installation of Transducers ...............................................1-4

1.4 Installation of Sensors ....................................................1-14

2. Wiring ...............................................................2-1

3. Initial Settings..................................................3-1

3.1 NMEA Setting ..................................................................3-1

3.2 Output Data Sentences .....................................................3-3

3.3 Antenna Height.................................................................3-4

3.4 Baud Rate Setting (GP-1850DF only)..............................3-4

3.5 Beacon frequency Setting (GP-1850DF only) .................3-5

3.6 Depth Adjustment.............................................................3-6

3.7 External Equipment Setup (Option) .................................3-7

3.8 Selecting the Echo Sounder Output Power ....................3-10

4. Installation of DGPS Beacon Receiver

(for GP-1850F) .................................................4-1

APPENDIX TRIDUCER 525ST-PWC/PWD .......AP-1

PACKING LIST .................................................... A-1

OUTLINE DRAWINGS......................................... D-1

INTERCONNECTION DIAGRAM ........................ S-1

SCHEMATIC DIAGRAM ...................................... S-2

C

9-52, Ashihara-cho,

Nishinomiya, Japan

Telephone: 0798-65-2111

Telefax: 0798-65-4200

Your Local Agent/Dealer

All ri

g

hts reserved.

PUB. No. IME-43950-J

GP-1850F/1850DF

(

HIMA

)

FIRST EDITION : FEB. 1999

J : NOV. 01, 2001

Printed in Japan

iiiiiiiiiiiii

i

Ground the equipment to

prevent electrical shock

and mutual interference.

Confirm that the power supply voltage

is compatible with the voltage rating

of the equipment.

Connection to the wrong power supply

can cause fire or equipment damage. The

voltage rating appears on the label at the

rear of the display unit.

Use the correct fuse.

Use of a wrong fuse can cause fire or

equipment damage.

Keep the following compass safe

distance.

Standard Steering

Display Unit 0.98 m 0.74 m

CAUTION

When handling the transducer cable,

keep in mind the following points.

• Keep the cable away from oil and

fuel.

• Keep the cable away from the

place where it may be damaged

during the installation.

• Do not paint the cable.

The sheath of the transducer cable is

made of chlorophrene rubber (or vinyl

chloride). Therefore, do not paint the

sheath with organic liquid (such as

toluene) since it may harm the sheath.

WARNING

Do not work inside the

equipment unless totally

familiar with electrical

circuits.

Hazardous voltage which can

shock, burn or cause serious

injury exists inside the equip-

ment.

Turn off the power at the

mains switchboard before

beginning the installation.

Post a sign near the switch

to indicate it should not be

turned on while the equip-

ment is being installed.

Fire, electrical shock or

serious injury can result if the

power is left on or is applied

while the equipment is being

installed.

SAFETY INSTRUCTIONS

Safety Instructions for the Installer

ii

Equipment Lists

Standard supply

.oNemaNepyT.oNedoCytQskrameR

1tinuyalpsiD

E-F0581-PG-1F0581-PGrof

E-FD0581-PG- FD0581-PGrof

2tinuannetnA

710-APG-

1

F0581-PGrof

810-APG- FD0581-PGrof

910-APG- FD0581-PGrof

3recudsnarT

DSP5-025521-510-000

1.enotceles,tuptuoW006rofDWP5-025621-510-000

DSM5-025721-510-000

4straperapS10520-41PS062-573-4001esuF

5slairetamnoitallatsnI00250-41PC694-140-0001 .yssaelbaC,elbacrewoP

6seirosseccA

10420-41PF072-573-4001revocdraH

20420-41PF051-673-4001

,lebalkramtuptuo,swercS

noihsucrebbur

Optional equipment

.ONemaNepyT.oNedoCskrameR

1

reviecernocaeB

tik

810-A01-0581-208-RG894-140-000

pihw,A0007-RG,810-APG

annetna

810-N01-0581-208-RG405-140-000A0007-RG,810-APG

S810-A51-0581-209-RG994-140-000

pihw,A0007-RG,S810-APG

annetna

S810-N51-0581-208-RG505-140-000A0007-RG,810-APG

910-N01-0581-208-PG846-140-000A0007-RG,910-APG

S910-N51-0581-209-RG946-140-000A0007-RG,S910-APG

2

elbacannetnA

.yssa

51-D3-SP-CNT076-331-000

elbacannetnarof,m51

noisnetxe

3

elbacannetnA

tes

00710-02PC011-273-400

elbacannetnarof,m03

noisnetxe

01710-02PC021-273-400

elbacannetnarof,m05

noisnetxe

4.yssAelbaC050-3000FPS7A-JM10-037-631-000

5

tnuomtsaM

erutxif

1110-02PC087-563-400

6

elgna-thgiR

esabannetna

033AQ-31.oN932-308-000

tinuannetnagnitnuomrof7

annetnaelgna-L

esab

013AQ-31.oN042-308-000

8

esabannetnA

gnitnuomliarrof

0615CR-31.oN411-608-000

iii

Optional equipment (con't)

.oNemaNepyT.oNedoCskrameR

9tinuannetnA

S810-APG264-140-000FD0581-PGrof

610-APG635-140-000F0581-PGrof

S910-APG455-140-000FD0581-PGrof

01recudsnarT

DSP5-025521-510-000W006rof

DWP5-025621-510-000W006rof,tnuommosnartelbacm8/w

DSM5-025721-510-000

,rotcennocfoorpretawdnaelbacm8/w

W006rof

T1-002/05071-510-000Wk1rof

11yssaelbaC2904S20484-431-000noitcennocrecudsnartWk1rof

21xobgnihctaM0001-BM908-040-000noitcennocrecudsnartWk1rof

31rosnesTS

BSM20-TS689-731-000epytlluh-urhT

BSP20-TS789-731-000epytlluh-urht,elbacm8/w

41StiklluhrennI033AQ-31.oN042-308-000tinuannetnagnitnuomrof

51

erutarepmeT

rosnes

BTM20-T620-040-000

BSM20-T040-040-000

BSM30-T720-040-000

61recudirT

DSM-TS425422-510-000

W006rof

DSM-TS525362-510-000

DWP-TS025821-510-000

W006rof

DWP-TS525162-510-000

71

retrevnoC

noitcennoc

7414S20280-141-000

81reifitceR26-RP

484-310-000CAV001rof

584-310-000CAV011rof

684-310-000CAV022rof

784-310-000CAV032rof

91.yssaelbaC

050-1100FPS6A-JM442-231-000m5,P4-P6,radarnoitcennocrof

001-1100FPS6A-JM633-231-000m01,P4-P6,radarnoitcennocrof

050-2100FPS6A-JM424-431-000m5,P6-P6,S/Erodiavanrof

001-2100FPS6A-JM718-331-000m01,P6-P6,S/Erodiavanrof

02annetnapihW2.1-WAF640-631-000FD0581-PGrof

12

etomeR

rellortnoc

E-F581-CMR023-573-400yrettab,revoclyniv,rellortnoC

22draCMAR400-CM20MAR00097-173-400BM2

32

nocaeBSPGD

revieceR

08-RG-F0581-PGrof

iv

System Configuration

The GP-1850F/1850DF mainly consists of a display unit, a GPS antenna and a

dual frequency transducer. A DGPS beacon receiver is provided inside the display

unit for GP-1850DF type. The mini chart card drive in the display unit loads elec-

tronic charts. External equipment which can be connected include water tempera-

ture and speed sensors, autopilot, and DGPS beacon receiver (GP-1850F).

Ship’s mains

10.8—31.2 VDC

External equipment

(Autopilot, etc.)

DGPS beacon receiver

GP-1850F only

Transducer

Temp. sensor

(option)

ANTENNA UNIT

Receives signal from

GPS satellite and beacon

reference station

(GP-1850DF only).

DISPLAY UNIT

Ship’s position is

calculated in longitude

and latitude from signal

received from the an-

tenna unit and displayed

on the screen.

GPA-017

(for GP-1850F)

GPA-018

(for GP-1850DF)

1.2 m Whip antenna

(Option)

*Matching

Box

MB-1000

*Required for 1 kW transducer only

GPA-019

(for GP-1850DF)

1-1

1. Installation of Standard Equipment

1.1 Installation of Display Unit

Mounting considerations

The display unit can be installed on a tabletop, on the overhead or flush mounted

in a console or panel.

OverheadTabletopHard Cover

Figure 1-1 Tabletop, overhead mounting methods

When selecting a mounting location for the display unit keep the following in mind:

• Keep the display unit out of direct sunlight.

• The temperature and humidity should be moderate and stable.

• Locate the unit away from exhaust pipes and vents.

• The mounting location should be well ventilated.

• Mount the unit where shock and vibration are minimal.

• Keep the unit away electromagnetic field generating equipment such as motor,

generator.

• For maintenance and checking purposes, leave sufficient space at the sides

and rear of the unit and leave slack in cables.

• A magnetic compass will be affected if placed too close to the display unit.

Observe the following compass safe distances to prevent disturbance to the

magnetic compass:

Standard compass: 0.98 meters

Steering compass: 0.74 meters

• Rubber cushions which absorb vibration (supplied) may be attached as below

if vibration is a problem.

45±5mm

Aline with edge

of hanger.

Rubber cushion

TM-166 No.18 black

1-2

Mounting procedure

Follow the procedure below to mount the display unit on a tabletop or the over-

head.

Tabletop, overhead mounting

1. Fix the hanger by four tapping screws M5 X 16.

2. Screw knob bolts in display unit, set it to hanger, and tighten knob bolts.

3. Attach hard cover to protect LCD.

WARNING

Figure 1-2 Tabletop, overhead mounting of display unit

Flush mounting

Note:

Use supplied pan head screws when the thickness of the bulkhead is from

11 to 14 mm. For bulkhead which exceeds 14 mm in thickness the length of the

pan head screws should be bulkhead thickness plus 7.3±1.5 mm. Also the length

of B below should max. 7 mm.

B

A

1. Prepare a cutout in the mounting location whose dimensions are as shown in

Figure 1-3.

2. Fix the display unit by six pan head screws. Refer to the outline drawing on

page D-2.

1-3

Flush mount

Pan head screws

Cutout for flush mount

242 0.5

50

89 0.5

147 0.5

6-R2.25

244 1

143 1

15 0.5

238 1

Figure 1-3 Flush mounting of display unit

1.2 Installation of Antenna Unit

Mounting considerations

Install the antenna unit referring to the installation diagram on page D-3 or D-4.

When selecting a mounting location for the antenna unit, keep in mind the follow-

ing points:

• Select a location out of the radar beam. The radar beam will obstruct or prevent

reception of the GPS satellite signal.

• The location should be well away from a VHF antenna. A GPS receiver is inter-

fered by a harmonic wave of a VHF antenna.

• There should be no interfering object within the line-of-sight to the satellites.

Objects within line-of-sight to a satellite, for example, a mast, may block recep-

tion or prolong acquisition time.

• Mount the antenna unit as high as possible. Mounting the antenna unit as high

as possible keeps it free of interfering objects and water spray, which can inter-

rupt reception of GPS satellite signal if the water freezes.

• The length of the whip antenna for the GP-1850DF should be no longer than

1.2 meter to prevent antenna damage. Do not use a 2.5 meter whip antenna.

• If the antenna cable is to be passed through a hole which is not large enough to

pass the connector, you may unfasten the connector with a needle nose pliers

and 3/8-inch open-end wrench. Refasten it as shown in Figure 1-4 after run-

ning the cable through the hole.

Center pin (soldered)

Clamp nut

Connector shell

Gasket (reddish brown)

Washer

Shield

Figure 1-4 How to assemble the connector

1-4

1.3 Installation of Transducers

Installing the inside-hull mount transducer

Necessary tools

You will need the following tools:

• Sandpaper (#100)

• Silicone sealant

Remarks on installation

• Do the installation with the boat hauled out of the water.

• Turn off the engine while installing the equipment.

• Install the transducer in the engine room.

Selecting the mounting location

Keep the following points in mind when selecting a mounting location:

• The mounting location should be where the hull is of single-hull thickness and

is void of air or flotation materials other than solid fiberglass between the trans-

ducer face and the water.

• Do not place the transducer over hull struts or ribes which run under the hull.

• Avoid a location where the rising angle of the hull exceeds 15°, to minimize the

effect of the boat’s rolling.

• You will finalize the mounting location through some trial and error. The proce-

dure for this is shown later.

50cm

15cm

1/3

1/2

Mounting location

for transducer

Center line

Figure 1-5 Inside-hull transducer mounting location

1-5

Attaching the transducer

1. Clean the transducer face to remove any foreign material. Lightly roughen the

transducer face with #100 sandpaper. Also, roughen the inside of the hull where

the transducer is to be mounted.

2. Warm the silicone sealant to 40°C before usage to soften it. Coat the trans-

ducer face and mounting location with silicone sealant.

Transducer face

Silicone sealant

Figure 1-6 Coating the transducer face with silicone sealant

3. Press the transducer firmly down on the hull and gently twist it back and forth to

remove any air which may be trapped in the silicone sealant.

Hull

Silicone

sealant

Squeeze out

air bubbles.

Figure 1-7 Attaching transducer to hull with silicone sealant

1-6

Observing the picture

1. Press the [POWER] key to turn on the display unit.

2. Press the [SNDR] key to select the sounder display.

3. Press the soft key labeled "MODE/FREQ" to display the following message.

MODE/FREQ

▲

AUTO CRUISING

AUTO FISHING

MANUAL

▼

Figure 1-8 MODE FREQ selection screen

4. Select "MANUAL" by the arrow key.

5. Press the soft key labeled "RETURN".

6. Press the soft key labeled "GAIN" to display the following message.

GAIN

▲

HIGH

LOW

▼

50

Figure 1-9 GAIN adjustment screen

7. Confirm that Gain is set at 50 (midpoint).

8. Press the soft key labeled "RETURN".

9. Press the soft key labeled "RANGE".

10.Select "15ft" by the [▲] key.

11.Note the depth to the seabed.

1-7

30

°C

20

10

15

0

10

5

0.0

SNDR

FUNC

MODE/

FREQ

SHIFT

GAIN

RANGE

DGPS 3D 50kHz

32.8

SOUNDER

Figure 1-10 Video sounder picture

If the bottom is displayed in red and the light-blue color appears the mounting

location is suitable. You can leave the transducer in position.

If the bottom is not displayed in reddish brown, the mounting location is unsuit-

able. Relocate the transducer and do the following.

1. Press the [POWER] key to turn off the power.

2. Gently dismount the transducer with piece of wood.

3. Do steps 1 through 5 in the previous procedure. Repeat

until a suitable location is found.

Final preparation

Support the transducer with a piece of wood to keep it in place wile it is drying. Let

the transducer dry 24–72 hours.

1-8

Installing the thru-hull mount transducer

Transducer mounting location

This type of mounting provides the best performance of all, since the transducer

protrudes from the hull and the effect of air bubbles and turbulence neat the hull

skin is reduced. When the boat has a keel, the transducer should be at least 30 cm

away from it. Typical through hull mountings are shown in the figure on the next

page.

The performance of the video sounder is directly related to the mounting location

of the transducer, especially for high-speed cruising. The installation should be

planned in advance, keeping the standard cable length (8 m) and the following

factors in mind:

• Air bubbles and turbulence caused by movement of the boat seriously degrade

the sounding capability of the transducer. The transducer should, therefore, be

located in a position where water flow is the smoothest. Noise from the propel-

lers also adversely affects performance and the transducer should not be

mounted nearby. The lifting strakes are notorious for creating acoustic noise,

and these must be avoided by keeping the transducer inboard of them.

• The transducer must always remain submerged, even when the boat is rolling,

pitching or up on a plane at high speed.

• A practical choice would be somewhere between 1/3 and 1/2 of the boat's length

from the stern. For planing hulls, a practical location is generally rather far astern,

so that the transducer is always in water regardless of the planing attitude.

Transducer outline drawings

22

120

30

68 87

68

120

28

24

520-5PSD (option) 520-5MSD (option)

Ship's

bow

All dimensions

in millimeters

Figure 1-11 Transducer outline drawings

1-9

Acceptable transducer mounting locations

Deep-V hull

• Position 1/2 to 1/3 length of the hull from stern

• 15 to 30 cm off center line (inside first lifting strakes).

Figure 1-12 Transducer mounting location on deep-V hull

High speed V-planing hull

• Within the wetted bottom area

• Deadrise angle within 15°

Figure 1-13 Transducer mounting location on high speed

V-planing hull

Typical through-hull mount transducer installations

Flat washer

Rubber washer

Fairing block

Hull

bottom

Hull

bottom

Deep-V Hull Flat Hull

Figure 1-14 Typical through-hull mount transducer installations

1-10

Procedure for installing the thru-hull mount transducer

1. With the boat hauled out of the water, mark the location selected for mounting

the transducer on the bottom of the hull.

2. If the hull is not level within 15° in any direction, fairing blocks made out of teak

should be used between the transducer and hull, both inside and outside, to

keep the transducer face parallel with the water line. Fabricate the fairing block

as shown below and make the entire surface as smooth as possible to provide

an undisturbed flow of water around the transducer. The fairing block should be

smaller than the transducer itself to provide a channel to divert turbulent water

around the sides of the transducer rather than over its face.

Upper

half

Lower

half

Hole for

stuffing tube

BO

W

Saw along slope of hull.

Figure 1-15 Construction of fairing block

3. Drill a hole just large enough to pass the threaded stuffing tube of the trans-

ducer through the hull, making sure it is drilled vertically.

4. Apply a sufficient amount of high quality caulking compound to the top surface

of the transducer, around the threads of the stuffing tube and inside the mount-

ing hole (and fairing blocks if used) to ensure watertight mounting.

5. Mount the transducer and fairing blocks and tighten the locking nuts. Be sure

that the transducer is properly oriented and its working face is parallel to the

waterline.

Note:

Do not over-stress the stuffing tube and locking nuts through excessive tight-

ening, since the wood block will swell when the boat is placed in the water. It is

suggested that the nut be tightened lightly at installation and retightened several

days after the boat has been launched.

1-11

Installing the transom mount transducer

This type of mounting is very commonly employed, usually on relatively small I/O

or outboard boats. Do not use this method on an inboard motor boat because

turbulence is created by the propeller ahead of the transducer.

There are two methods of installation: flush with hull (for flat hulls) and projecting

from hull (for deep V-hulls).

Flat Hull Deep V-hull

D

D>

50 cm

Figure 1-16 Transom mount transducer mounting locations

Installing the transom mount transducer flush with hull

(for flat hulls)

A suitable mounting location is at least 50 cm away from the engine and where the

water flow is smooth.

1. Drill four pilot holes in the mounting location.

2. Attach the transducer to the bracket with tapping screws (supplied).

3. Adjust the transducer position so the transducer faces right to the seabed.

Note:

If necessary, to improve water flow and minimize air

bubbles staying on the transducer face, incline the trans-

ducer about 5° at the rear. This may require a certain amount

of experimentation for fine tuning at high cruising speeds.

4. Fill the gap between the wedge front of the transducer and transom with epoxy

material to eliminate any air spaces.

1-12

M5 x 20

No. 1

M5 x 14

5°

Tape

M5 x 20

Figure 1-17 Transom mount transducer, mounting flush with hull

Installing the transom mount transducer projecting from hull

(for deep-V hulls)

This method is employed on deep-V hulls and provides good performance be-

cause the effects of air bubbles are minimal. Install the transducer parallel with

water surface; not flush with hull. If the boat is placed on a trailer care must be

taken not to damage the transducer when the boat is hauled out of the water and

put on the trailer.

M5 x 20

M5 x 14

No. 2

Figure 1-18 Transom mount transducer, projecting from hull

Transducer preparation

Before putting the boat in water, wipe the face of the transducer thoroughly with a

detergent liquid soap. This will lessen the time necessary for the transducer to

have good contact with the water. Otherwise the time required for complete "satu-

ration" will be lengthened and performance will be reduced.

Do not paint the transducer. Performance will be affected.

1-13

Triducer 524ST-MSD, 525ST-MSD

The triducer is designed for thru-hull mounting.

Mounting considerations

When selecting a mounting location keep the following points in mind:

• Air bubbles and turbulence caused by movement of the boat seriously degrade

the sounding capability of the transducer. The transducer should, therefore, be

located in a position where water flow is the smoothest. Noise from the propel-

lers also adversely affects performance and the transducer should not be

mounted nearby. The lifting strakes are notorious for creating acoustic noise,

and these must be avoided by keeping the transducer inboard of them.

• The transducer must always remain submerged, even when the boat is rolling,

pitching or up on a plane at high speed.

• A practical choice would be somewhere between 1/3 and 1/2 of the boat’s length

from the stern. For planing hulls, a practical location is generally rather far astern,

so that the transducer is always in water regardless of the planing attitude.

∅79 mm

133 mm

2.00"-12 UN

threads

∅51 mm

140 mm

27 mm

7 mm

Figure 1-19 Dimensions of triducer 524ST-MSD/525ST-MSD

1-14

1.4 Installation of Sensors

Transom mount water temperature sensor

T-02MTB

• Fix the cable at a convenient location with cable clamp.

• When the cable is led in through the transom board, make a hole of approx. 17

mm diameter to pass the connector. After passing the cable, fill the hole with a

sealing compound.

D>50 cm

D

M5 x 20

Mount sensor

flush with hull bottom.

Figure 1-20 How to install transom mount water temperature sensor T-02MTB

Page is loading ...

Furuno GP-1850DF User manual

This manual is also suitable for

Furuno GP-1850DF User manual

Related papers

Other documents