Classic Exhibits VK-1960 Setup Instructions

Type
Setup Instructions
© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
10’
VK-1960 Inline Lightbox
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
REV 05/2023
© 2023
Order #XXXXX Grid View
Locked layer contains
placeholder marks.
= 1 sq foot
© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2023
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation
© 2023
Order #XXXXX
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI110 Frame Assembly
© 2023
Case 1 of 1
Order #XXXXX Case Packing
Top View of Each Level
Level 1 Level 2 Level 3 Level 4 Level 5
4A4
2
6 6A
7,7A
Shelf
Wings
Base
Plates
35 5A
2A 3A
Shelf
Shelf
Setup Hardware
Monitor Mount
© 2023
Step 1 of 2
Order #XXXXX Backwall Assembly
1
4
Transformer
6
6A
2
3
5
5A
4A
2A
3A
7A
7
1
Item
1
2,2A
3,3A
4,4A
5,5A
6,6A
7,7A
Qty.
2
1,1
1,1
1,1
1,1
1,1
1,1
Description
Base Plate
45”w CEI110 Horizontal Extrusion
45”h CEI110 Horizontal Extrusion
42”h CEI110 Vertical Extrusion
42”h CEI110 Vertical Extrusion
42”h S91 Vertical Extrusion
40.187”h Z33 Vertical Extrusion
Steps:
1) Attach base plates [1] to horizontals [2] & [3] using bolts, washers, and wing nuts.
2) Assemble horizontals [2 to 3] [2A to 3A] and verticals [4 to 5] [4A to 5A] together.
See CEI-110 Frame Assembly sheet for instruction.
3) Attach verticals [7-7A] between horizontal assemblies.
4) Connect verticals [6] & [6A] together.
5) Attach vertical assembly [6/6A] to assembly [4A/5A], using bolts.
See S91 to CEI110 Attachment detail.
6) Connect lighting cords and attach transformers. See
Light to Light Connections & Light to Transformer details.
7) Install SEG graphic to front of assembled frame and blocker fabric to back.
See SEG Graphic Installation sheet for details.
*
*
*
Power
Break
Power
Break
Transformer
Connector
S91
CEI110
S91 to CEI110 Attachment
*
Bolt
Slide connector into groove of S91
extrusion. Tighten set screws to secure
connector. Attach CEI110 extrusion
to S91, using bolt.
Lighting Installation Warning
Bolt Nylon
Washer
If utilizing your own hardware,
purchase nylon washers to prevent
metal screw heads from damaging
the circuit board.
Attach no more than seven lights
per chain.
Diamond
Washer
++
--
Lights Male
Light to Light Attachment
Maximum of 7 lights per chain,
12 lights per Transformer
Light to Transformer Attachment
+
-
Power
Female
Transformer
144W / 6 Amp / 24V
© 2023
Step 2 of 2
Order #XXXXX Backwall Attachments
6A
6
Completed Assembly
Monitor
Mount
Shelf
Shelf
Shelf
Steps:
1) Lock shelves to vertical [6]. See Shelf Attachment detail.
2) Attach monitor mount to vertical [6A]. See Monitor Mount Attachment detail.
3) Attach wings to top and sides, using A10 clamps. See A10 Clamp detail.
*
*
*
*
Shelf Attachment
Insert Lock into groove of vertical
extrusion and tighten Set Screw.
Lock
Set Screw
Shelf
*
Knob
Set Screw
Connector
1) Slide connector of clamp
into extrusion groove.
2) Tighten set screw when
A10 is in desired location.
3) Insert wing into clamp.
4) Tighten knob on clamp
to secure wing in place.
A10 Clamp
A10 Clamp
Monitor Mount Attachment
Connectors
V4
Connectors
*
Slide V4 Connectors into groove
of Extrusion. Tighten Set Screws
to secure connectors in place.
Attach Monitor Mount back
piece to Extrusion, using bolts.
Then slide monitor mount into
back piece.
Monitor
Mount
Back
Piece
Bolts
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Classic Exhibits VK-1960 Setup Instructions

Type
Setup Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI