Onset CX405 User manual

Brand: Onset

Model: CX405

Type: User manual

Onset CX405 is a Bluetooth-enabled data logger designed for accurate temperature monitoring in extreme cold conditions. With a built-in external probe, it measures temperatures as low as -95°C (-139°F) and provides reliable data for cold chain monitoring. The device's wireless communication allows for easy configuration and data download using the InTemp app or InTempConnect software, enabling efficient data management and analysis.

InTemp® CX405 RTD Dry Ice Logger Manual

25469-H

The InTemp CX405 RTD dry ice logger is designed for Cold Chain monitoring and has a built-in

external probe that measures temperatures as low as -95°C (-139°F). This Bluetooth® Low Energy-

enabled logger is designed for wireless communication with a mobile device. Using the InTemp app,

you can configure the logger, perform daily logger checks, download reports, and monitor tripped

alarms. Or you can use InTempConnect® to configure and download CX series loggers via the CX

Gateway. The InTempVerify™ app is also available to download loggers and automatically upload

reports to InTempConnect. (Note: InTempVerify is for downloading and continuing loggers only. It

cannot configure, start, or restart the loggers.) Use the LCD screen on the logger to check the current

temperature, logging status, battery usage, and more. Once data is uploaded to InTempConnect, you

can track logger configurations and automatically upload logger data to build custom reports.

Specifications

External Temperature Probe

Range -95° to 50°C (-139° to 122°F)

Accuracy ±1.5°C from -95° to -40°C (±2.7°F from -139° to -40°F)

±1.0°C from -40° to -10°C (±1.8°F from -40° to 14°F)

±0.5°C from -10° to 50°C (±0.9°F from -14° to 122°F)

Resolution 0.05°C at 25°C (0.09°F at 77°F)

Drift <0.1°C (0.18°F) per year

NIST Calibration Two-point NIST calibration, probe only

Cable Length 1.5 m (4.92 ft)

Probe Dimensions Food-grade stainless steel probe with blunt tip, 31.75 mm (1.25 inches)

long, 4.78 mm (0.188 inches) diameter

Ambient Temperature Sensor

Range -30° to 70°C (-22° to 158°F)

Accuracy ±0.5°C from -15° to 70°C (±0.9°F from 5° to 158°F)

±1.0°C from -30° to -15°C (±1.8°F from -22° to 5°F)

Resolution 0.024°C at 25°C (0.04°F at 77°F)

Drift <0.1°C (0.18°F) per year

Logger

Radio Power 1 mW (0 dBm)

Transmission Range Approximately 30.5 m (100 ft) line-of-sight

Wireless Data Standard Bluetooth Low Energy (Bluetooth Smart)

Logger Operating Range -30° to 70°C (-22° to 158°F), 0 to 95% RH (non-condensing)

Logging Rate 1 second to 18 hours

Time Accuracy ±1 minute per month at 25°C (77°F)

Battery Type Two AAA 1.5 V alkaline or lithium batteries, user replaceable

Battery Life 1 year, typical with logging interval of 1 minute. Faster logging intervals,

remaining connected with the app, excessive report generation,

numerous audible alarms, and paging all impact battery life.

Memory 128 KB (75,245 total measurements or 37,622 probe & internal paired

measurements)

Full Memory Download

Time

Approximately 60 seconds; may take longer the farther the device is

from the logger

LCD LCD is visible from 0° to 50°C (32° to 122°F); the LCD may react slowly or

go blank in temperatures outside this range

Dimensions 9.4 x 4.5 x 2.59 cm (3.7 x 1.77 x 1.02 inches)

Weight 90.2 g (3.18 oz)

Environmental Rating IP54

The CE Marking identifies this product as complying with all relevant

directives in the European Union (EU).

Refer to the last page.

Passed RTCA DO160G, part 21H

InTemp CX405 RTD Dry Ice

Logger

Included Items:

• Two AAA 1.5 V alkaline

batteries

• Battery door and screw

• NIST Certificate of Calibration

Required Items:

• InTemp app

• Device with iOS or Android™

and Bluetooth

InTemp CX405 RTD Dry Ice Logger Manual

1-508-743-3309 (U.S. and International) 2 www.onsetcomp.com

Logger Components and Operation

Start Button: Press this button for 1 second to start the logger

when it is configured to start “on button push.”

Mute or Next Button: Press this button for 1 second to mute a

beeping alarm (see Logger Alarms) or to switch between the

external probe and ambient internal sensor temperature

readings. Press and hold this button for 3 seconds to clear the

minimum and maximum values (see Minimum and Maximum

Values). Press and hold this button and the Start button for 5

seconds to reset a passkey (InTemp app users only; see Passkey

Protections).

Magnets: There are four magnets on the back of the logger (not

shown in diagram) for mounting.

Temperature Sensor: This internal sensor measures ambient

temperature.

Temperature Probe: This is the built-in external probe for

measuring temperature.

Audible Alarm Speaker: This is the speaker for the audible

alarm that beeps when an alarm is tripped.

Alarm LED: This LED blinks every 5 seconds when an alarm is

tripped (see Logger Alarms).

LCD: This screen shows the latest temperature reading and

other status information. The LCD screen refreshes at the same

rate as the logging interval. The example shows all symbols

illuminated on the LCD screen followed by a table with

descriptions of each symbol.

LCD Symbol Description

An alarm has tripped because the temperature

reading is outside the specified range. See Logger

Alarms.

LCD Symbol Description

The logger has been configured to perform daily or

twice daily checks (twice daily is shown in this

example), but no checks have been performed yet.

The once daily or twice daily logger check (twice in

this example) has been performed.

This indicates how much memory has been used

for the current configuration. In this example,

approximately 40 percent of the memory has been

used.

This shows the approximate battery power

remaining.

The logger is currently logging.

The logger is currently connected to a phone or

tablet via Bluetooth. The more bars there are, the

stronger the signal.

The logger is waiting to be started. Press and hold

the Start button for 3 seconds to start the logger.

This is an example of a temperature reading from

the external probe.

This is an example of a temperature reading from

the internal sensor.

This is an example of a minimum temperature,

which is the lowest probe temperature reading

from the day within the current 24-hour period

(midnight from one day to midnight the next day)

if the logger was set to record logger checks (see

Performing Logger Checks). To clear this value,

press the Mute/Next button for 3 seconds. If the

logger check setting is not enabled, the minimum

reading represents the entire logging period and

only resets when the logger is downloaded and

restarted or stopped and reconfigured, or if you

press the Mute/Next button for 3 seconds (see

Minimum and Maximum Values).

This is an example of a maximum temperature,

which is the highest probe temperature reading

from the day within the current 24-hour period

(midnight from one day to midnight the next day)

if the logger was set to record logger checks (see

Performing Logger Checks). To clear this value,

press the Mute/Next button for 3 seconds. If the

logger check setting is not enabled, the maximum

reading represents the entire logging period and

only resets when the logger is downloaded and

restarted or stopped and reconfigured, or if you

press the Mute/Next button for 3 seconds (see

Minimum and Maximum Values).

MUTE indicates an alarm is beeping. Turn off the

beeping alarm by pressing the Mute button. The

LCD then changes to MUTED.

The audible alarm has been muted.

The logger has been configured to start logging on

a delay. The display will count down in days,

hours, minutes, and seconds until logging begins.

In this example, 5 minutes and 38 seconds remain

until logging will begin.

The profile settings are being loaded onto the

logger.

An error occurred while loading the profile

settings onto the logger. Try reconfiguring the

logger.

Temperature probe

LCD

Alarm LED

Start button

Audible alarm

speaker

One of four

magnets (on

back of logger)

Temperature

sensor (behind

rectangular

plug)

Mute or Next

button

InTemp CX405 RTD Dry Ice Logger Manual

1-508-743-3309 (U.S. and International) 3 www.onsetcomp.com

LCD Symbol Description

The logger was paged from the InTemp app.

The logger has been downloaded and stopped

with the InTemp app or because the memory is

full.

The logger is being updated with new firmware.

Note: If the logger has stopped logging because the memory is

full, the LCD screen remains on and displays STOP until you

have downloaded data from the logger to your mobile device.

Once the logger has been downloaded, the LCD turns off

automatically after 2 hours. The LCD turns back on the next

time the logger connects with your device.

Getting Started

InTempConnect is web-based software that allows you to

monitor logger configurations and view downloaded data

online. Using the InTemp app, you can configure the logger

with your phone or tablet and then download reports, which

are saved in the app and automatically uploaded to

InTempConnect. The CX Gateway is also available to

automatically configure and download loggers and upload data

to InTempConnect. Or anyone can download a logger using the

InTempVerify app if the loggers are enabled to be used with

InTempVerify. See www.intempconnect.com/help for details on

both the gateway and InTempVerify. If you do not need to

access logged data via the cloud based InTempConnect

software, then you also have the option to use the logger with

the InTemp app only.

Follow these steps to begin using the loggers with

InTempConnect and the InTemp app.

1. Administrators: Set up an InTempConnect account. Follow

all steps if you are a new administrator. If you already have

an account and roles assigned, follow steps c and d.

If you are using the logger with the InTemp app only, skip

to step 2.

a. Go to www.intempconnect.com and follow the prompts

to set up an administrator account. You will receive an

email to activate the account.

b. Log into www.intempconnect.com and add roles for the

users you will be adding to the account. Select System

Setup and then Roles. Click Add Role, enter a description,

select the privileges for the role and click Save.

c. Select System Setup and then Users to add users to your

account. Click Add User and enter the email address and

first and last name of the user. Select the roles for the

user and click Save.

d. New users will receive an email to activate their user

accounts.

2. Set up the logger. Insert two AAA batteries in the logger,

observing polarity. Insert the battery door in the back of the

logger making sure it is flush with the rest of the logger

case. Use the included screw and a Phillips-head

screwdriver to screw the battery door into place.

3. Download the InTemp app and log in.

a. Download InTemp to a phone or tablet from the App

Store® or Google Play™.

b. Open the app and enable Bluetooth in the device settings

if prompted.

c. InTempConnect users: Log in with your InTempConnect

account email and password from the InTempConnect

User screen.

InTemp app only users: Swipe left to the Standalone User

screen and tap Create Account. Fill in the fields to create

an account and then log in from the Standalone User

screen.

4. Configure the logger.

InTempConnect users: Configuring the logger requires

sufficient privileges. The logger includes preset profiles.

Administrators or those with the required privileges can

also set up custom profiles (including setting up daily logger

checks) and trip information fields. Do this before

configuring the logger. If you plan to use the logger with the

InTempVerify app, then you must create a logger profile

with InTempVerify enabled. See

www.intempconnect.com/help for details.

Note: You can create, edit, and delete logger profiles in the

In Temp app. All changes you make in the app are reflected

in your InTempConnect account.

InTemp app only users: The logger includes preset profiles.

To set up a custom profile, tap the Settings icon and tap

CX400 Logger. Also, if you need to perform daily logger

checks, tap Record CX400 Logger Checks under Settings and

select Once Daily or Twice Daily. Do this before configuring

the logger.

See www.intempconnect.com/help for details on setting up

custom profiles in both the app and InTempConnect and on

setting up trip information.

a. Tap the Devices icon in the app. Find the logger in the list

and tap it to connect to it.

If you are having trouble connecting:

• Make sure the logger is within range of your mobile

device. The range for successful wireless

communication is approximately 30.5 m (100 ft) with

full line-of-sight.

• If your device can connect to the logger intermittently

or loses its connection, move closer to the logger,

within sight if possible.

• Change the orientation of your phone or tablet to

ensure the antenna in your device is pointed toward

the logger. Obstacles between the antenna in the

device and the logger may result in intermittent

connections.

• If the logger appears in the list, but you cannot connect

to it, close the app, power down the mobile device,

and then turn it back on. This forces the previous

Bluetooth connection to close.

b. Once connected, tap Configure. Swipe left and right to

select a logger profile. Type a name or label for the

logger. Tap Start to load the selected profile to the

logger. InTempConnect users: If trip information fields

were set up, you will be prompted to enter additional

information. Tap Start in the upper right corner when

done.

5. Deploy and start the logger. Deploy the logger to the

location where you will be monitoring the temperature.

Logging will begin based on the settings in the profile

selected. If the logger was configured to perform daily

InTemp CX405 RTD Dry Ice Logger Manual

1-508-743-3309 (U.S. and International) 4 www.onsetcomp.com

checks, connect to the logger and tap Perform (Morning,

Afternoon, or Daily) Check every day.

Once logging begins, the logger will display the current

temperature reading and the minimum and maximum readings

within the current 24-hour period (midnight from one day to

midnight the next day) if the logger was set to record logger

checks (see Performing Logger Checks). Otherwise, the

minimum and maximum readings represent the entire logging

period and only reset when the logger is downloaded and

restarted or stopped and reconfigured (they will not reset if you

download the logger and continue logging). These minimum

and maximum values are also available in the logger reports

(see Downloading the Loggers). Click Next to switch between

external probe and ambient temperature readings. Minimum

and maximum readings are only available for the external

probe.

Logger Alarms

You can set up an alarm to trip on the logger when the

temperature reading falls above or below a specified value or

when the logger battery is low. Specific alarm settings are set in

the logger profile that you create in either InTempConnect or in

the app.

When a temperature alarm trips:

• The logger LED blinks every 5 seconds.

• The alarm icon appears on the LCD and in the app.

• The logger beeps once every 15 seconds (unless audible

alarms are disabled in the logger profile).

• An Alarm Tripped event is logged.

When a low battery alarm trips:

• The battery icon on the LCD flashes.

• The logger quickly beeps three times every 15 seconds.

• A Low Battery event is logged.

To mute a beeping alarm, press the Mute button on the logger.

Once muted, you cannot turn the beeping back on. Note that if

a temperature alarm is occurring at the same time as a low

battery alarm, pressing the mute button silences both alarms.

Download data from the logger to view details about a tripped

alarm and to clear temperature alarm indicators in the app and

on the LCD. Replace the batteries in the logger to clear a

battery alarm. Note: Download the logger before replacing the

batteries to ensure no data is lost.

Passkey Protection

The logger is protected by an encrypted passkey automatically

generated by the InTemp app for InTempConnect users and

optionally available if you are using the InTemp app only. The

passkey uses a proprietary encryption algorithm that changes

with every connection.

InTempConnect Users

Only InTempConnect users belonging to the same

InTempConnect account can connect to a logger once it is

configured. When an InTempConnect user first configures a

logger, it is locked with an encrypted passkey that is

automatically generated by the InTemp app. After the logger is

configured, only active users associated with that account are

able to connect to it. If a user belongs to a different account,

that user is not able to connect to the logger with the InTemp

app, which displays an invalid passkey message. Administrators

or users with the required privileges can also view the passkey

from the device configuration page in InTempConnect and

share them if needed. See www.intempconnect.com/help for

more details. Note: This does not apply to InTempVerify. If the

logger was configured with a logger profile in which

InTempVerify was enabled, then anyone can download the

logger with the InTempVerify app.

InTemp App Only Users

If you are using the InTemp app only (not logging in as an

InTempConnect user), you can create an encrypted passkey for

the logger that is required if another phone or tablet attempts

to connect to it. This is recommended to ensure that a

deployed logger is not mistakenly stopped or purposely altered

by others.

To set a passkey:

1. Tap the Devices icon and connect to the logger.

2. Tap Set Logger Passkey.

3. Type a passkey up to 10 characters.

4. Tap Save.

5. Tap Disconnect.

Only the phone or tablet used to set the passkey can then

connect to the logger without entering a passkey; all other

mobile devices are required to enter the passkey. For example,

if you set the passkey for the logger with your tablet and then

try to connect to the device later with your phone, you will be

required to enter the passkey on the phone but not with your

tablet. Similarly, if others attempt to connect to the logger with

different devices, then they would also be required to enter the

passkey. To reset a passkey, simultaneously press both the top

and bottom button on the logger for 5 seconds, or connect to

the logger, tap Set Logger Passkey, and select Reset Passkey to

Factory Default.

Downloading Data from the Logger

You can download data from the logger to a phone or tablet

and generate reports that include logged probe and ambient

readings, events, user activity, alarm information, and more.

Reports can be shared immediately upon download or accessed

later in the InTemp app.

InTempConnect users: Privileges are required to download,

preview, and share reports in the InTemp app. Report data is

automatically uploaded to InTempConnect when you download

the logger. Log into InTempConnect to build custom reports

(requires privileges). In addition, InTempConnect users can also

download CX loggers automatically on a regular basis using the

CX Gateway. Or, if the logger was configured with a logger

profile in which InTempVerify was enabled, then anyone can

download the logger with the InTempVerify app. For details on

the gateway and InTempVerify, see www.intempconnect/help.

To download the logger with the InTemp app:

1. Tap the Devices icon and connect to the logger.

2. Tap Download.

3. Choose a download option:

• Download & Continue. The logger continues logging once

the download is complete.

• Download & Restart. The logger starts a new data set

using the same profile once the download is complete.

InTemp CX405 RTD Dry Ice Logger Manual

1-508-743-3309 (U.S. and International) 5 www.onsetcomp.com

• Download & Stop. The logger stops logging once the

download is complete.

To download data from multiple loggers with the InTemp app:

1. Tap Devices, then Bulk Download.

2. The screen changes to Bulk Download mode. This changes

the way the screen behaves when you tap on a logger tile.

Tap on a tile to select it for bulk download. You can select

up to 20 loggers. Text at the bottom of the page updates to

indicate how many loggers are selected.

3. Tap Download X Loggers to begin the download.

• Download & Continue. The loggers continue logging

once the download is complete.

• Download & Restart (CX400, CX450, CX503, CX603, and

CX703 models only). The logger starts a new

configuration using the same profile once the download

is complete. You will be prompted to enter trip

information again (if applicable). Note that if the logger

profile is set up to start with a button push, you must

push the button on the logger for logging to restart.

• Download & Stop. The logger stops logging once the

download is complete. The downloads begin and run

one after another. The screen displays the download

queue.

4. Click Cancel to cancel the downloads and return to the

Devices screen, not in Bulk Download mode.

5. The screen displays Done when all the loggers are

downloaded.

A report of the download is generated and is also uploaded to

InTempConnect if you are logged into the InTemp app with

your InTempConnect user credentials. If you are using the bulk

download feature, one report per logger is generated.

In the app, tap Settings to change the default report type and

report sharing options. The report is also available in Secure

PDF, XLSX, and VFC CSV (if enabled) formats for sharing later.

Tap the Reports icon to access previously downloaded reports.

See www.intempconnect.com/help for details on working with

reports in both the InTemp app and InTempConnect.

Performing Logger Checks

If your monitoring application requires that you perform daily

or twice daily checks of the logger, you can use the InTemp app

to connect to the logger and perform a check.

To enable the perform check feature in the InTemp app (if you

are not using InTempConnect):

1. Tap the Settings icon.

2. Under Record CX400 Logger Checks, select either Once

Daily or Twice Daily. If you choose Twice Daily, a Perform

Morning Check action will be listed in the Connected screen

from 12:01 AM until 12:00 PM and then a Perform

Afternoon Check action will be listed from 12:01 PM to

12:00 AM. If you choose Once Daily, an action will be listed

in the Connected screen to Perform Daily Check.

To enable the perform check feature if you are using

InTempConnect, an administrator or user with the required

privileges must create a new profile for a CX400 logger and set

the Daily Checks to Once Daily or Twice Daily. For details on

managing profiles, see www.intempconnect.com/help.

Note: Changes to the Record CX400 Logger Checks setting will

take effect the next time the logger is configured. Also, when

this setting is enabled, the minimum and maximum values

displayed on the logger LCD represent the minimum and

maximum readings within the current 24-hour periods and will

reset every 24 hours. Otherwise, if this setting is not enabled,

the minimum and maximum values represent the entire logging

period and only reset when the logger is downloaded and

restarted or stopped and reconfigured (they will not reset if you

download the logger and continue logging).

To perform a check:

1. Tap the Devices icon and connect to the logger.

2. Tap Perform (Morning, Afternoon, or Daily) Check.

Once a check is completed, it is recorded as a logged user

action along with the user email and the location and is

available for view in reports. The action is also listed as

performed in the Connected screen and a checkmark will

illuminate on the logger LCD.

You can also set up a notification to display on your phone or

tablet to remind you to perform a check. Use the Reminders

option under Settings in the InTemp app.

Minimum and Maximum Values

The logger LCD displays the minimum and maximum

temperature readings. If the setting to perform logger checks is

enabled (see Performing Logger Checks), then these values

represent the minimum and maximum readings within the

current 24-hour period and will reset every 24 hours for the

entire logging period. If the logger check setting has not been

enabled, then these values represent the entire logging period

and will automatically reset when the logger is downloaded and

restarted or stopped and reconfigured.

You can also clear these values as needed while the logger is

logging by pressing the Mute/Next button for 3 seconds until

HOLD disappears on the LCD. Dashes (--) will then appear on the

LCD for the minimum and maximum values until the next logging

interval. The values will then continue to be updated for the

remaining logging period or until they are cleared again. Note:

This clears the data on the screen only. Actual logger and

reporting data will not be cleared with this reset.

Logger Events

The logger records the following events to track logger

operation and status. These events are listed in reports

downloaded from the logger.

Event Name Definition

Started The logger started logging.

Stopped The logger stopped logging.

Downloaded The logger was downloaded.

Probe Alarm

Tripped/Cleared

A probe temperature alarm has tripped or

cleared because the reading was outside the

alarm limits or back within range.

Performed/Missed

Check

The user performed or missed the daily,

morning, or afternoon logger check.

Safe Shutdown The battery level dropped below 1.85 V; the

logger performs a safe shutdown.

InTemp CX405 RTD Dry Ice Logger Manual

1-508-743-3309 (U.S. and International) 6 www.onsetcomp.com

Deploying the Logger

Use the four magnets on the back of the logger case to mount it

to a magnetic surface.

The external probe cable has a protective sheath. Move the

sheath as needed to position it where the cable will be

protected during shipments from inadvertent cuts.

Protecting the Logger

The logger is designed for indoor use and can be permanently

damaged by corrosion if it gets wet. Protect it from

condensation. If the logger gets wet, remove the battery

immediately and dry the circuit board.

Note: Static electricity may cause the logger to stop logging.

The logger has been tested to 8 KV but avoid electrostatic

discharge by grounding yourself to protect the logger. For more

information, search for “static discharge” on onsetcomp.com.

InTemp CX405 RTD Dry Ice Logger Manual

1-508-743-3309 (U.S. and International)

www.onsetcomp.com/intemp/contact/support

InTempVerify are trademarks or registered trademarks of Onset Computer Corporation. App Store is a service

mark of Apple Inc. Google Play is a trademark of Google Inc. Bluetooth is a registered trademark of Bluetooth

SIG, Inc. Bluetooth and Bluetooth Smart are registered trademarks of Bluetooth SIG, Inc. All other trademarks

are the property of their respective companies.

Patent #: 8,860,569 25469-H

Battery Information

The logger requires two user-replaceable AAA 1.5 V alkaline or

optional lithium batteries for operation at the extreme ends of

the logger operating range. Expected battery life varies based

on the ambient temperature where the logger is deployed, the

frequency of connecting to the phone or tablet and

downloading reports, the duration of audible alarms, and

battery performance. New batteries typically last 1 year with

logging intervals greater than 1 minute. Deployments in

extremely cold or hot temperatures or a logging interval faster

than 1 minute can impact battery life. Estimates are not

guaranteed due to uncertainties in initial battery conditions and

operating environment.

Note: Make sure the batteries installed have flat negative

terminals. There should be no indent in the bottom of the

batteries. Batteries with indents in the negative terminals may

become loose and prevent proper operation.

To install or replace the batteries:

1. Download the logger before replacing the batteries to

ensure no data is lost.

2. If the battery door is already installed on the back of the

logger, use a Phillips-head screwdriver to remove it.

3. Remove any old batteries.

4. Insert two new batteries observing polarity.

5. Screw the battery door into place.

WARNING: Do not cut open, incinerate, heat above 85°C

(185°F), or recharge lithium batteries. The batteries may

explode if the logger is exposed to extreme heat or conditions

that could damage or destroy the battery case. Do not dispose

of the logger or batteries in fire. Do not expose the contents of

the batteries to water. Dispose of the batteries according to

local regulations for lithium batteries.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Industry Canada Statements

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

Avis de conformité pour l’Industrie Canada

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)

l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.

To comply with FCC and Industry Canada RF radiation exposure limits for general population, the logger must be installed to provide a separation distance of at least 20cm from

all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Pour se conformer aux limites d'exposition aux rayonnements RF de la FCC et d'Industrie Canada pour la population générale, l'enregistreur doit être installé de manière à

fournir une distance de séparation d'au moins 20 cm de toutes les personnes et ne doit pas tree colocalisé ou fonctionner avec une autre antenne ou un autre émetteur.

Only use batteries

with flat negative

terminals

Do not use batteries with an

indent in the negative terminal

Onset CX405 User manual

Onset CX405 User manual

Related papers

Other documents