2. Baxton Studio
  3. MG9002-Ash Walnut-2DW-NS

Baxton Studio MG9002-Ash Walnut-2DW-NS Assembly Instructions

  • Hello! I've reviewed the assembly instructions for the 9002 2-drawer nightstand. This document provides a complete parts list and a step-by-step guide on how to assemble your new nightstand. It emphasizes using two people during assembly and avoiding power tools. I'm ready to assist you with any questions you might have about the assembly process or the parts included.
  • How many people are needed for assembly?
    Is it okay to use power tools for the assembly?
    What does the 'Parts List' include?
9002 2 Drawer Nightstand
Assembly Instructions
Page 1 of 7
WI-1220
Parts List
1
F
Side Panel
(Left Hand) x 1
G
Side Panel
(Right Hand) x 1
E
Post x 4
ATo p Panel x 1
BBottom Panel x 1
CSupport Bar x 2
DBack Panel x 1
Note: Do not assemble
using power tools.
This can cause the bolts
to be overtightened
Use 2 People
HDrawer Face x 2 JDrawer Back x 2
KDrawer Side
(Left Hand) x 2
LDrawer Side
(Right Hand) x 2
MDrawer
Bottom x 2
9002 2 Drawer Nightstand
Assembly Instructions
Page 2 of 7
Hardware List
2
H
3
3
K
L
Important: Assemble
the Drawer Runner
facing Drawer Face.
Assemble the Drawer Sides (K & L)
to the Drawer Face (H).
3x 2
1M6 x 15mm
JCB x 16 2M6 x 60mm
JCB x 8
12 Allen Key
x 1
9'L' Bracket
(5005-3)
x 8
3M4 x 25mm
Wood
Screw x 16
K
M
L
H
3
3
K
J
L
Assemble the Drawer Back (J) to
the Drawer Sides (K & L).
5
Slide the Drawer Bottom (M) into the
groove on the Drawer Sides (K & L).
4
5M4 x 16mm
Wood
Screw x 6
7Spring
Washer
x 8
8Flat
Washer
x 8
WI-1220
CSK Cap
Wood Screw
(M6 x 50mm) x 4
10 M4 x 18mm
Wood Screw
x 2
11 Handle
(1005)
x 2
64 M4 x 20mm
Wood
Screw x 8
1
x 4
1
x 8
9
F
G
Bottom holes
to assemble
Bottom Panel
Bottom holes
to assemble
Bottom Panel
9002 2 Drawer Nightstand
Assembly Instructions
Page 3 of 7
Fit the 'L' Bracket
to the Side Panel (F & G).
6
A
Rail facing back
Groove
Groove
F
Hole to assemble
Bottom Panel
Hole to assemble
Bottom Panel
G
Back
Assembled the
Side Panel (F & G)
to the Top Panel (A).
7Important:
Drawer Runner
facing front.
WI-1220
A
F
G
C
C
9002 2 Drawer Nightstand
Assembly Instructions
Page 4 of 7
Fit the Support Bar (C) to the
Side Panel (F & G).
8
Slide the Back Panel (D) into the groove
on the back of the Side Panel (F & G).
9
1
x 4
D
F
G
Groove
Groove
Back
Back
WI-1220
9002 2 Drawer Nightstand
Assembly Instructions
Page 5 of 7
Fit the Bottom Panel (B) to the Bottom of the Side Panel (F & G).
10
6
B
F/G
Rail
facing
back
WI-1220
Use screws to tighten the
Back Panel (D) to the
back of the frame.
11
B
D
F
G
B
5
F
5
D
G
Back
Back
12
H
JCB
E
B
8
7
2
9002 2 Drawer Nightstand
Assembly Instructions
Page 6 of 7
WI-1220
B
E
A
E
D
E
Fit the Post (E) to the Bottom Panel (B).
12
Fit and adjust the Drawer Face (H).
13
NOTE: Before fitting the Wood Screws.
Lossen the JCBs on the Drawer Face if
the face needs alignment.
*
H
9002 2 Drawer Nightstand
Assembly Instructions
Page 7 of 7
Finally, fit the Handle to the Drawer Face (H).
15
H
WI-1220
After the Drawer Faces (H) are aligned,
secure with wood screws.
14
10 11
H
4
H
H
/