2. Baxton Studio
  3. MG9002-Ash Walnut-4DW-Chest

Baxton Studio MG9002-Ash Walnut-4DW-Chest Assembly Instructions

  • Hello! I have reviewed the assembly instructions for the 9002 Drawer Chest. This document provides a detailed guide for assembling the four-drawer chest, including parts lists, hardware information, and step-by-step procedures for each stage of the assembly process. I'm ready to assist you with any questions you may have about the assembly process or features of the dresser.
  • How many people are required to assemble?
    Can I use power tools for assembly?
    What should I do if the drawer face needs alignment?
9002 4 Drawer Chest
Assembly Instructions
Page 1 of 7
WI-1220
Parts List
1
Parts in Box A:
Note: Do not assemble
using power tools.
This can cause the bolts
to be overtightened
Use 2 People
D
Post x 4
ATo p Panel x 1
BBottom Panel x 1
CBack Panel x 2
HDrawer Bottom x 4
Support Bar x 2
E
Side Panel
(Left Hand) x 1
F G
Side Panel
(Right Hand) x 1
M6 x 25mm
Wood Dowel
x 16
9002 4 Drawer Chest
Assembly Instructions
Page 2 of 7
Parts List
1
J
4
4
6M
L6
N
Important: Assemble the
Drawer Runner facing
Drawer Face.
Hardware List
2
1M6 x
15mm JCB
x 16
8'L' Bracket
(5005-3) x 8
Parts in Box B:
13 Allen Key
x 1
6
Assemble the Drawer Sides (M & N) & Drawer Rail (L)
to the Drawer Face (J).
3x 4
MDrawer Side
(Left Hand) x 4 NDrawer Side
(Right Hand) x 4
4M4 x 25mm
Wood Screw
x 40
2M6 x
60mm JCB
x 8
7CSK Cap Wood Screw
(M6 x 50mm) x 4
WI-1220
JDrawer Face x 4 KDrawer Back x 4 LDrawer Rail x 4
10 Flat Washer
x 8 11 M4 x 18mm
Wood Screw x 8 12 Handle
(1005) x 8
3M4 x 20mm
Wood Screw
x 24
9Spring
Washer x 8
5M4 x 32mm
Wood Screw
x 12
9002 4 Drawer Chest
Assembly Instructions
Page 3 of 7
Slide the Drawer Bottom (H) into the
groove on the Drawer Sides (M & N).
4
M
H
NJ
4
4M
K
N
Assemble the Drawer Back (K) to
the Drawer Sides (M & N).
5
Turn the Drawer over to fit angled 25mm Wood
screws (4) to the Drawer Rail (L).
6
K
4
L
J
x 4
WI-1220
1
x 8
8
1
x 4
F
G
Bottom holes
to assemble
Bottom Panel
Bottom holes
to assemble
Bottom Panel
9002 4 Drawer Chest
Assembly Instructions
Page 4 of 7
Fit the 'L' Bracket
to the Side Panel (F & G).
7
Assembled the Top Panel (A) &
Bottom Panel (B) to the
Side Panel (F & G).
8
7
B
F
G
7Hole to assemble
Bottom Panel
A
Back
Rail facing back
Rail facing back
Important:
Drawer Runner
facing front.
WI-1220
E
E
A
B
G
F
9002 4 Drawer Chest
Assembly Instructions
Page 5 of 7
Fit the Support Bar (E) to the
Side Panel (F & G) as shown.
9
B
C
C
F
A
Attached the Back Panel (C)
to the back of the frame.
10
1
x 4
5
x 12
Back
Back
WI-1220
10
2
D
B
9
9002 4 Drawer Chest
Assembly Instructions
Page 6 of 7
Turn the chest over to fit the Post (D)
to the Bottom Panel (B).
11
B
D
D
A
J
Fit and adjust the Drawer Face (J).
12
WI-1220
13
J
JCB
NOTE: Before fitting the Wood Screws.
Lossen the JCBs on the Drawer Face if
the face needs alignment.
*
9002 4 Drawer Chest
Assembly Instructions
Page 7 of 7
After the Drawer Faces (J) are aligned,
secure with wood screws.
13
J
Finaly, fit the Handle to the Drawer Face (J).
14
WI-1220
11
12 J
3
J
J
/