DKS 1601-195, 1601-197, 1601-198 Heater / Fan Kits User manual
- Category
- Gate Opener
- Type
- User manual
9200 HEATER AND FAN ASSEMBLY KITS
These kits are designed for the 9200 model gate operators. For cold weather climates where temperatures routinely drop below 40°F
(4°C). A built-in thermostat will automatically control the temperature inside operator housing.
DoorKing Part Numbers
1 HP9210 115 VAC
65 105 180 275
16.3
208 VAC
230 VAC
208 VAC
230 VAC
1 HP
1 HP
2 HP
2 HP
9210
9210
9220
9220
8.4
8.3
14.9
15.1
208 VAC
230 VAC
460 VAC
208 VAC
230 VAC
460 VAC
208 VAC
230 VAC
208 VAC
230 VAC
1 HP
1 HP
1 HP
2 HP
2 HP
2 HP
3 HP
3 HP
3 HP
3 HP
9210
9210
9210
9220
9220
9220
9230/9240
9230/9240
9235
9235
6.7
6.8
5
10.0
9.6
6.6
13.2
13.0
16.2
16.0
DO NOT use the “high voltage wire size and distance limitations” table in the Installation/Owner’s manuals to determine the high
voltage AC input power wire size and distance limitations for the gate operator because of a much greater current draw when using
the heater. Use the tables below to determine the wire size and distances for your chosen gate operator when a heater is installed.
EACH operator should have a “Dedicated” circuit breaker at the power source.
If the high voltage AC input power wiring is greater than the maximum distance shown, it is recommended that a service feeder be
installed. When large gauge wire is used, a separate junction box must be installed for the operator connection. Wire run distances
are based on NEC guidelines for copper wire allowing a maximum 3% voltage drop on the line. The calculated distance was then
further reduced by 10% to allow for other loses in the system. Never run low voltage rated wire insulation in the same conduit as
high voltage rated wire insulation. Keep them in separate conduits.
High Voltage AC Input Power for the 9200 Gate Operator with a Heater
High voltage AC input wire size and distance limitations for a 9210 - 115 VAC with a heater.
High voltage AC input wire size and distance limitations for a 9200 - 208/230/460 VAC with a heater.
1
ø
Wire Size / Max Distance in Feet
Operator
and
Heater
Amps
ModelPhase (Ø) Horsepower Volts
240
270
135
145
300
325
420
200
230
340
150
170
125
140
12 AWG
385
430
215
235
480
525
670
320
370
545
245
275
195
220
10 AWG
640
715
360
395
805
875
1100
540
620
905
405
455
330
370
8 AWG
965
1080
540
590
1210
1315
1500
810
930
1360
610
690
500
560
6 AWG
1601-197
1601-197
1601-197
1601-197
1601-197
1601-197
1601-198
1601-197
1601-197
1601-198
1601-197
1601-197
1601-197
1601-197
Heater Kit P/N
Wire Size / Max Distance in Feet
Operator
and
Heater
Amps
ModelPhase (Ø) Horsepower Volts 12 AWG 10 AWG 8 AWG 6 AWG
1601-195
Heater Kit P/N
In bi-parting (dual) gate applications, high voltage AC input power
is required for EACH 9200 operator with heater.
1
ø
3
ø
Note: EACH operator should have a “Dedicated 20 Amp” minimum circuit breaker at the power source.
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
115 VAC Model
6.6 Amp
1601-195 Kit
208/230 VAC Models
3.3 Amp
1601-197 Kit
460 VAC Models
3.3 Amp
1601-198 Kit
Power
Wires
ON
OF
F
Electronic Box
ON
OF
F
DANGER
HOT!
WARNING
M
OVING
GATE CAN CAUS
E
Op
era
te
g
a
te
o
n
ly
w
h
en g
a
te
a
re
a
i
s
i
n
s
ig
ht
and
fr
e
e of
p
eo
p
l
e
an
d
o
b
st
r
u
c
ti
o
n
s.
Do
n
ot al
low
chi
ld
re
n
to
p
l
a
y
i
n ga
te ar
e
a
o
r
o
p
e
ra
te
g
a
te
.
Do
n
ot st
a
nd
in
g
a
te
p
ath
or
w
a
lk th
rou
gh
p
a
th whil
e gate is
m
ov
i
ng
.
Rea
d
o
w
n
er’
s
m
an
u
al an
d
s
afety
in
struc
tion
s.
S
ERIOUS
INJUR
Y OR DEAT
H
CL
AS
S
CE
RT
I
F
I
E
D
T
O
CAN
/
CSA
C2
2
.2
NO.
2
4
7
CO
N
F
ORMS
T
O
ANSI
/UL-
3
2
5
VEHICU
LA
R
G
A
TE
O
PE
R
A
TO
R
HP
53
3
82
MO
DEL
SE
R
I
A
L
VO
L
T
S
PHAS
E
AMPS
6
0
Hz
MAX
GAT
E
L
OAD
Door
Ki
ng
, I
nc
.
,
I
ng
l
ewood, CA
Mounting Plate
1
2
3
Heater
1601-167-E-5-14
Copyright 2014 DoorKing, Inc. All rights reserved.
Installation of Heater
Each Kit Includes: Heater with 2 securing bolts / mounting plate with 2 bolts and nuts.
Shut off the AC input power to the operator from
the circuit breaker.
Remove clear plastic electronic box cover. Remove the 3 locknuts
inside the electronic box to swing box open.
Bolt mounting plate to heater with 2 supplied bolts and nuts.
Slide heater into the gear reducer bracket as shown below and
bolt heater to the bracket with 2 supplied securing bolts.
Run the 2 power wires as shown below.
Keep wires away from the heater vents and make sure
wires do not get pinched in the electronic box’s folding hinge.
ON - Normal setting.
Automatically turns the
heater and fan ON when
the temperature drops
below 40°F (4°C) inside
the operator, and turns
the heater and fan OFF
when the temperature
rises above 55°F (13°C)
inside the operator.
Heater Switch
ON
OFF
OFF - Turns
the heater/fan
off.
Hot
L1 L2 L3 L4 L5
Neu
115 VAC
208/230/460 VAC
1-Phase and 3-Phase
Hot Hot Hot
DANGER
HIGH VOLTAGE!
DANGER
HIGH VOLTAGE!
DANGER
HOT!
Connect the 2 heater power wires
according to operator AC power type.
Note: The gear reducer bracket may need to
be spread apart a little to get the heater to
slide in.
Older 9200s must have 2 holes drilled in the
gear reducer bracket for the securing bolts.
Power Connection
1601-197 Kit (208/230 VAC)
1601-198 Kit (460 VAC)
1601-195 Kit
G
ear
R
educer
Bracket
Lo
cknu
t
Lo
cknut
Lo
cknut
Power Wires
Clear Plastic Electronic Box Cover
Access Door
Securing
Bolts
L1 L2 L3 L4 L5
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
DoorKing Part Numbers
115 VAC Model
6.6 Amp
1601-195 Kit
208/230 VAC Models
3.3 Amp
1601-197 Kit
460 VAC Models
3.3 Amp
1601-198 Kit
-
1
-
2
DKS 1601-195, 1601-197, 1601-198 Heater / Fan Kits User manual
- Category
- Gate Opener
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
DKS 1601-154 Heater / Fan Kit User manual
-
-
-
-
-
-
-
-
-