Mountain Buggy urban / terrain car seat clip Operating instructions

Brand: Mountain Buggy

Model: urban / terrain car seat clip

Category: Strollers

Type: Operating instructions

Mountain Buggy urban / terrain car seat clip is a device designed to attach a car seat to a stroller frame, allowing you to transport your baby safely and conveniently. It is compatible with the Peg Perego Primo Viaggio car seat and the Peg Perego Terrain and Urban strollers.

The car seat clip is easy to install and remove, making it a convenient option for parents who need to switch between using their car seat and stroller. It features snap locks that securely attach it to the stroller frame, ensuring that your baby is safe and secure while riding.

To install the car seat clip, you will need to temporarily remove the sunhood from the stroller and unfasten the two middle fasteners on both sides of the stroller. Once the car seat clip is in place, you can reattach the sunhood and fasteners.

IMPORTANT - KEEP FOR FUTURE REFERENCE

SCCPis21/4/08gen

WARNING

• CheckyouhavethePegPéregomodel:

primoviaggioCarSeatforthisCarseat

Clip.

• Donotusethisaccessoryonanyother

strollerasitmaybeunsafe.

• DonotusethisCarseatClipuntilyouhave

readandunderstoodtheinstructions!

• Incorrectusecanmeanseriousinjuryor

deathtoaninfant!

• Neverleaveyourchildunattended.

• CheckthatcarseatandCarseatClipare

secureandcannotmoveforward,back,

sidewaysorupwards.

• Makesureinfantisharnessedintothecar

seatusingthecarseatmanufacturer’s

instructions.

• Donotleavebabyincarseat(onoroff

stroller)forlongperiodsoftime.

Pull support wire out of

sunhood joint A. This

operation is child proof

and therefore requires a

degree of force. To assist

in pulling support wire out,

push against stroller frame

with other hand B.

1.TemporarilyRemoveSunhood

Repeat step (1) on other

side.

Unfasten two middle

fasteners on both sides

of stroller (at B & C) and

peel fabric back, exposing

frame.

2.PartialSeatUnfastening

Single - T1204

Single - U1204

ThisCarseatCliponlytsthePegPéregomodel:

primoviaggio.

These instructions are for the Peg Pérego Carseat Clip

which t the following model strollers only:

SINGLE CarSEat CLIp INStruCtIoNS

Sunhood Joint

URBAN

TERRAIN

STAGEONE

ALL MODELS

Loosen the strap beneath

seat at point A.

URBAN

Recline seat slightly.

Sunhood

Joint

The stroller seat does not need to be removed to t Carseat Clip.

The sunhood wires need to be removed from sunhood joints to allow

Carseat Clip to be tted. These wires are re-attached to stroller once

Carseat Clip has been tted.

pEG pÉrEGo

model:primoviaggio

FittingCarseatCliptoFrame

STAGETWO

FittingCarSeatontoCarseatClip

STAGETHREE

OPENPOSITION CLOSEDPOSITION

WARNING

• Makesureinfantisharnessedintothecarseatusing

thecarseatmanufacturer’sinstructions.

• WhenttingcarseatontoCarseatClip,ALWAYS

KEEPASTEADYINGHANDONCARSEATAND

INFANT.

• CheckCarseatClipislocatedcorrectlyontostroller

frame.Referbacktodiagramstoensurepositioning

ofsnaplocksarecorrect.

• CheckcarseatandCarseatCliparesecureand

cannotmoveforward,back,sidewaysorupwards.

• DonotuseCarseatClipifyouareunabletosecure

carseatorCarseatClip.Inthiscasecontactstore

wherestrollerwaspurchasedordistributorforyour

country,formorehelp.

• IT IS RECOMMENDED THAT YOU PRACTISE

THEFOLLOWINGINSTRUCTIONSWITHOUT

INFANTINCARSEAT.

Place car seat in CarseatClip so that

infant is facing the stroller handle bar.

STAGEFOUR

RemovingCarseatClipfromStroller

STAGEFIVE

Close all Snap Locks down at, making sure you hear the lock “click”-

indicating they are fully locked.

PicturedonUrban

Snap Locks

TheCarseatClipcomesassembledforUrbanmodel.

Open all four Snap Locks by lifting up levers.

Press CarseatClipon to frame so that TOPSnap Locks are directly

above sunhood joints (on both sides).

(i) Using Allen Key supplied, remove Snap Locks at points B (both sides

by rotating screw in an anti-clockwise direction.

(ii) Using Allen Key supplied, fasten removed Snap Locks at points C

(both sides) by rotating screw in a clockwise direction until screw is

tight and Snap Locks are secure.

Before placing Carseat Clip

on stroller frame, the Snap

Locks at points B need to

be removed and placed at

points C (on both sides).

“CLICK”

TERRAIN & URBAN

TERRAIN ONLY

Sunhood

Joint

Sunhood

Joint

URBAN TERRAIN

Re-AttachingSunhoodWires

Push sunhood wires back into sunhood joints (refer Stage One)

Remove sunhood wires (refer Stage One).

Open all four Snap Locks by lifting up levers.

Lift Carseat Clip off stroller frame.

Re-attach sunhood wires (refer Stage Three).

Re-attach two middle fasteners on both sides of stroller.

Tighten strap beneath seat (refer Stage One).

URBAN

Ensure the car seat latches have clicked

on to the CarseatClip bars A&B.

Bar C ts into car seat slot.

RemovingCarSeatfromCarseatClip

Carseat Clip Bars

Unlock the car seat from the Carseat Clip by pulling the latch handle

and ling car seat upwards.

Latch Handle

Slot

Latches

Allen Key

Snap Locks

Mountain Buggy urban / terrain car seat clip Operating instructions

Brand: Mountain Buggy

Model: urban / terrain car seat clip

Category: Strollers

Type: Operating instructions

Download PDF

report

Mountain Buggy urban / terrain car seat clip Operating instructions

Mountain Buggy urban / terrain car seat clip Operating instructions

Related papers

Other documents