Mountain Buggy double & triple urban / terrain car seat clip Operating instructions

Brand
Mountain Buggy
Model
double & triple urban / terrain car seat clip
Type
Operating instructions
These instructions are for the Carseat Clip that ts the primo viaggio
infant car seat made by Peg Pérego only. This Carseat Clip ts the
following model strollers:
IMPORTANT, KEEP FOR FUTURE REFERENCE
DTCCPis9/05/08gen
- DOUBLE/TRIPLE CARSEAT CLIP INSTRUCTIONS
WARNING
• CheckyouhavethePegPérego:modelprimo
viaggiocarseatforthisCarseatClip.
• DonotusethisCarseatClipuntilyouhaveread
andunderstoodtheinstructions!
• Incorrectusecanmeanseriousinjuryordeathto
aninfant!
• Donotusethisaccessoryonanystrollerother
thanthoselisted,asitmaybeunsafe.
• Neverleaveyourchildunattended.
• CheckthatcarseatandCarseatCliparesecure
andcannotmoveforward,back,sidewaysor
upwards.
• Makesureinfantisharnessedintothecarseat
usingthecarseatmanufacturer’sinstructions.
• Donotleavebabyincarseat(onoroffstroller)
forlongperiodsoftime.
STAGE 1
PEG PÉREGO
Model: primo viaggio
DOUBLE U2204
URBAN
TRIPLE U3204
URBAN
DOUBLE T2204
TERRAIN
TRIPLE T3204
TERRAIN
Unfasten fasteners (x) either
side of right-hand seat and peel
fabric back, exposing right-hand
side tube and centre bar.
1
Recline right-hand seat slightly.
2
ALL MODELS
Loosen the strap beneath
seat at point A.
URBAN
1.TemporarilyRemoveSunhood
The sunhood wires need to be removed from sunhood joints to allow
Carseat Clip to be tted. These wires are re-attached to stroller once
Carseat Clip has been tted.
STAGE 2
ALL MODELS
1.PartialSeatUnfastening
Note: The Carseat Clip ts to right hand seat only. Left and right are
determined from pusher position.
Pull support wire out of
sunhood joint A while
pushing against stroller frame
with other hand B.NB: This
operation is child proof and
therefore requires a degree
of force.
Repeat step (1) on other
side.
Fold sunhood back to rest on
handlebar.
3
2
A
B
Sunhood Joint
1
X
A
centre
bar
3
The stroller seat does not need to be removed to t Carseat Clip.
WARNING
• CheckCarseatClipislocatedcorrectlyontostroller
frame.Referbacktodiagramstoensurepositioning
ofSnapLocksarecorrect.
• CheckcarseatandCarseatCliparesecureand
cannotmoveforward,back,sidewaysorupwards.
• DonotuseCarseatClipifyouareunabletosecure
carseatorCarseatClip.Inthiscasecontactstore
wherestrollerwaspurchasedordistributorforyour
country,formorehelp.
RemovingCarSeatfrom
Carseat Clip
Pull up car seat latch handle
to release car seat from Carseat
Clip bars.
Lift car seat off Carseat Clip.
Remove sunhood wires (refer Stage 1).
Open both Snap Locks by lifting up levers.
Lift Carseat Clip off stroller frame
Re-attach sunhood wires (refer Stage 3).
Re-attach two middle fasteners on both sides of seat.
Tighten strap beneath seat (refer Stage 1).
FittingCarseatCliptoFrame
STAGE 2
STAGE 3
WARNING
• Makesureinfantisharnessedintothecarseatusing
thecarseatmanufacturer’sinstructions.
• WhenttingcarseatontoCarseatClip,ALWAYS
KEEPASTEADYINGHANDONCARSEATAND
INFANT.
• IT IS RECOMMENDED THAT YOUPRACTISE
THEFOLLOWINGINSTRUCTIONSWITHOUT
INFANTINCARSEAT.
NB:TheCarseatClipcomesassembledfortheUrbanmodel.
Assembled for Urban
Assembled for Terrain
2
1
RemovingCarseatClipfromStroller
Sunhood Joint
Snap Locks
TerrainModelOnly
Before placing Carseat Clip on stroller frame, the Snap Lock at point
B needs to be removed and placed at point C.
(i) Using Allen Key supplied, remove Snap Lock at point B by rotating
screw in an anti-clockwise direction.
(ii) Using Allen Key supplied, place removed Snap Lock at point C by
rotating screw in a clockwise direction until screw is tight and Snap
Lock is secure.
Snap Locks
TERRAINANDURBANMODELS
Open both Snap Locks by lifting up levers.
1
Side
tube
Sunhood
joint
Press Carseat Clip on to right-
hand side tube of frame so that
the top Snap Lock is directly
above Sunhood Joint.
3
Close both Snap Locks down
at, making sure you hear the
lock “click” indicating they are
fully locked.
4
Pictured on Urban
STAGE 4
STAGE 5
Car seat latch
handle
1
2
1
2
Sliding
Plate
X Groove
Sliding
Plate
Allen Key
A
B
B A
C
Allen Key
Snap Locks
Centre bar
2
Ensure the car seat latches
have clicked on to the
Carseat Clip bars A &
B. Bar C ts into car seat
slot.
Car seat
slot
Car seat
latches
C
B
A
X Groove
Locate centre bar lug on
stroller and slide the Carseat
Clip Sliding Plate down the
centre bar of frame until
Groove (X) in Sliding Plate
locks onto centre bar lug.
Place car seat in Carseat
Clip so that infant is facing
away from stroller handle
bar.
URBAN
TERRAIN
Snap
Lock Lever
OPEN POSITION
URBAN
TERRAIN
Sunhood Joint
Snap Locks
CLOSEDPOSITION
“CLICK”
Fitting Car Seat onto Carseat Clip
3
4
5
URBAN
6
centre
bar
lug
RettingSunhood
Place sunhood in position and push
one side of wire into plastic joint.
Repeat on other side by pulling wire
away from frame at the top. Fasten
sunhood fabric to stroller frame and
seat, near handle bar.
  • Page 1 1
  • Page 2 2

Mountain Buggy double & triple urban / terrain car seat clip Operating instructions

Brand
Mountain Buggy
Model
double & triple urban / terrain car seat clip
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents