2. Baby & children
  3. Baby travel
  4. Strollers
  5. Mountain Buggy
  6. urban / terrain car seat clip

Mountain Buggy urban / terrain car seat clip Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Mountain Buggy urban / terrain car seat clip Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
IMPORTANT - KEEP FOR FUTURE REFERENCE
SCCGis21/2/08gen
WARNING
• DonotusethisCarseatClipuntilyouhave
readandunderstoodtheinstructions!
• Incorrectusecanmeanseriousinjuryor
deathtoaninfant!
• Donotuseaccessoriesnotdesignedfor
yourstrollerastheymaybeunsafe.
• Neverleaveyourchildunattended.
• CheckyouhavethecorrectCarseatClip
foryourcarseat.
• CheckthatcarseatandCarseatClipare
secureandcannotmoveforward,back,
sidewaysorupwards.
• Makesureinfantisharnessedintothecar
seatusingthecarseatmanufacturer’s
instructions.
• Donotleavebabyincarseat(onoroff
stroller)forlongperiodsoftime.
Pull support wire out of
sunhood joint A. This
operation is child proof
and therefore requires a
degree of force. To assist
in pulling support wire out,
push against stroller frame
with other hand B.
1
1.TemporarilyRemoveSunhood
Repeat step (1) on other
side.
2
Unfasten two middle
fasteners on both sides
of stroller (at B & C) and
peel fabric back, exposing
frame.
1
2
3
2.PartialSeatUnfastening
Single - T1204
Single - U1204
These instructions are for the Carseat Clip which t the
following model strollers:
Graco
®
model:SnugRide
®
SINGLE carSEat cLIp INStructIoNS -
A
B
Sunhood Joint
URBAN
TERRAIN
STAGEONE
ALL MODELS
A
ALL MODELS
Loosen the strap beneath
seat at point A.
URBAN
Recline seat slightly.
B
C
Sunhood
Joint
The stroller seat does not need to be removed to t Carseat Clip.
The sunhood wires need to be removed from sunhood joints to allow
Carseat Clip to be tted. These wires are re-attached to stroller once
Carseat Clip has been tted.
FittingCarseatCliptoFrame
STAGETWO
FittingCarSeatontoCarseatClip
STAGETHREE
OPENPOSITION CLOSEDPOSITION
WARNING
• Makesureinfantisharnessedintothecarseatusing
thecarseatmanufacturer’sinstructions.
• WhenttingcarseatontoCarseatClip,ALWAYS
KEEP A STEADYING HAND ON CAR SEAT
ANDINFANT,untilCarseatClipstrapissecurely
fastened.
• CheckcarseattsintoCarseatClipandbuckleis
rmlyfastened.
• CheckCarseatClipislocatedcorrectlyontostroller
frame.Referbacktodiagramstoensurepositioning
ofsnaplocksarecorrect.
• CheckcarseatandCarseatCliparesecureand
cannotmoveforward,back,sidewaysorupwards.
• DonotuseCarseatClipifyouareunabletosecure
carseatorCarseatClip.Inthiscasecontactstore
wherestrollerwaspurchasedordistributorforyour
country,formorehelp.
• ITISRECOMMENDEDTHAT YOUPRACTICE
THEFOLLOWINGINSTRUCTIONSWITHOUT
INFANTINCARSEAT.
Place car seat in CarseatClip so that
infant is facing the stroller handle bar.
1
Ensure the car seat latch has clicked on
to the CarseatClip bar.
2
Pass wide straps on each side of
Carseat Clip upward and through
slots provided on each side of car seat.
(The slots are the same openings as
used for car seat belt.)
3
Buckle the wide strap across top of car
seat and tighten rmly by pulling on free
end of strap.
4
RemovingCarSeatfromCarseatClip
STAGEFOUR
Carseat Clip Bar
UnbuckleCarseatClip buckle.
1
Remove straps from slots on car seat.
2
Pull up car seat latch handle to release
car seat from Carseat Clip bar.
3
RemovingCarseatClipfromStroller
STAGEFIVE
1
2
Close all Snap Locks down at, making sure you hear the lock “click”-
indicating they are fully locked.
3
PicturedonUrban
Snap Locks
Snap Locks
TheCarseatClipcomesassembledforUrbanmodel.
Open all four Snap Locks by lifting up levers.
Press CarseatClipon to frame so that TOPSnap Locks are directly
above sunhood joints (on both sides).
Allen Key
A
A
B
B
C
C
(i) Using Allen Key supplied, remove Snap Locks at points B (both sides
by rotating screw in an anti-clockwise direction.
(ii) Using Allen Key supplied, place removed Snap Locks at points C (both
sides) by rotating screw in a clockwise direction until screw is tight and
Snap Locks are secure.
Car Seat Latch
Lift car seat off Carseat Clip.
4
Car Seat
Latch
Handle
Before placing Carseat Clip
on stroller frame, the Snap
Locks at points B need to
be removed and placed at
points C (on both sides).
Snap Locks
“CLICK”
TERRAIN & URBAN
TERRAIN ONLY
Sunhood Joint
Sunhood Joint
URBAN TERRAIN
Re-AttachingSunhoodWires
Push sunhood wires back into sunhood joints (refer Stage One)
1
Remove sunhood wires (refer Stage One).
Open all four Snap Locks by lifting up levers.
Lift Carseat Clip off stroller frame.
Re-attach sunhood wires (refer Stage Three).
Re-attach two middle fasteners on both sides of stroller.
Tighten strap beneath seat (refer Stage One).
1
2
3
4
5
URBAN
6
/