Legrand LCAP32M Installation guide

Brand: Legrand

Model: LCAP32M

Type: Installation guide

Wattstopper

Commercial Power Enclosure Solutions and Main Lug Options

French Description

Spanish Description

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: IS-00706 – rev. 7

LCAP32M/S and LCAP 44M/S • Les Numéros de Catalogue • Los Números de Catálogo:

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

SOLUTION 1 - PARENT-LEVEL ENCLOSURE MODELS

OVERVIEW

The Wattstopper LCAP Series Commercial Enclosures ship with pre-congured modular solutions.

Load dimming and switching use Vantage™ controllers and switching products. The pre-congured

designs save time in Vantage’s Design Center™ software and during the installation process.

The LCAP32/44M/S series offers one of the highest amperage dimming and switching options in

the LCAP enclosure line. Vantage’s own forward and reverse phase dimming, use, patent pending,

individual load linearization curve settings. Each dimmed load’s starting/stopping points can also be

set. This technology is exclusive with Vantage and allows for smooth dimming and consistent lighting

using mixed lighting types and brands. The LCAP32/44M/S enclosures may be connected to other

LCAP enclosures and Vantage enclosures; scalable to virtually any size system. IMPORTANT: See

page 7 for optional Main Lug / circuit breaker models.

Enclosure Bus

Termination

OFFON

Enclosure

Select

Secondary Enclosure

Terminal Board

T/R+

T/R B

GND

Override

T/R+

T/R B

GND

Override

Main Enclosure Description

LCAP44 44” Architectural Enclosure

LCAP32 32” Architectural Enclosure

LCAP32/44M/S Panel Congurations

• LCAP32/44M (contains controller)

• LCAP32/44S (contains Secondary Terminal Board)

• KIT part numbers / Ordering Key, page 5

Panel Load Section:

• LCAP44M/S, up to 4 Modules

• LCAP32M/S, up to 2 Modules

Panel Controller Section:

• (1) IC-36-II Controller

-OR-

• (1) Secondary Terminal Board

Optional Parts Description

COM-HV-BARRIER Low-voltage Barrier

VA-RRU-1-120V Emergency Shunt Relay - 120V

VA-RRU-1-277V Emergency Shunt Relay - 277V

Additional Parts Order Separately Description

VA-EPC-DFS-120V Emergency Lighting Surface Mount Switch 120V

VA-EPC-DFS-277V Emergency Lighting Surface Mount Switch 277V

Part Number

Breakdown

Enclosure and Lid

ONLY

Panel

Type

LCAP32/44/M/S Optional Modules

LCAP32/44M/S With Module Options Module Type Location 1-4

Actual PN

Important See Ordering Key and Kit Part Numbers (pg. 5)

IS-00706 – Rev. 7

*InFusion controllers have a micro-SD ash card port for backup. Please see InFusion Controller Instruction Sheet for more details.

For module and emergency switch install sheet information, visit the Vantage Dealer Site.

LCAP M/S SERIES SPECIFICATIONS

LCAP ENCLOSURE DESIGNS

Specications LCAP32M / LCAP32S LCAP44M / LCAP44S

Cabinet Dimensions, HWD 32” x 24” x 4.575”

81cm x 61cm x 11.6cm

44.5” x 24” x 4.575”

113cm x 61cm x 11.6cm

Door Dimensions, HWD 32” x 24” x 0.75”

81cm x 61cm x 2cm

44.5” x 24” x 0.75”

113cm x 61cm x 2cm

Panel Insert, HWD 29.5” x 21” x 4.175”

75cm x 53.3cm x 10.6cm

42” x 21” x 4.175”

106.7cm x 53.3cm x 10.6cm

Weight - Enclosure 30 lbs / 13.61 kg 41 lbs / 18.6 kg

Weight - Door 15.5 lbs / 7.03 kg 20.7 lbs / 9.39 kg

Weight - Panel Insert 18.7 lbs / 8.48 kg 23 lbs / 10.43 kg

Number of Modules Up to 2 Up to 4

Load Capacity Up to 24 Up to 48

Line Feeds (Breakers) Up to 17 Up to 33

*Flash Memory (via controller)

Enclosure Finish Galvanized steel

Door Finish Black - Powder coated

Cover Vented, hinged

Wire Copper wire, MIN. of 176° F/ 80° C insulation

Ventilation Maintain 36” front clearance

Ambient Operating Temperature 32 - 104° F / 0 - 40° C

Ambient Operating Humidity 5 - 95% non-condensing

UL, CUL, and CE Listed Yes

LCAP SERIES ENCLOSURE FACTS

• Enclosures must be populated from left to right and top down

- Blank module positions cannot be left between lighting modules in Design Center setup

• Enclosures are pre-congured and wired (to the extent possible) using specic combinations of the following

componentsInstalled switching components are dependent on the enclosure design

- Components using high-voltage wiring

• Mixed high voltage wiring

- Components using low voltage control signal wiring

- Components using low voltage communication wiring

- Components using high voltage and low voltage connections made inside the enclosure

• The enclosure uses built-in barriers to separate high and low voltage wiring

• Some designs include the barrier while other designs require the barrier be added by the designer

- High voltage barriers may be installed between 120V/240V/277V load modules

• Enclosures may be setup as follows

- Main Enclosures Containing: One Main Enclosure Terminal Board (36V) and one IC-36-II InFusion Controller - OR -

- Secondary Enclosures Containing: One Secondary Enclosure Terminal Board

EULA

In order to enhance the security of our products, Legrand ships its products with all insecure ports closed and insecure protocols

disabled. You are free to congure your device as needed, but in doing so note that you may be decreasing the security of your

device and any information contained in the device. As you modify the device’s default settings, keep in mind how this may impact

the security of the device and your network. In addition, you should use caution in connecting your device to the Internet, especially

if you have altered the default security settings. If you have any questions or concerns about how your modications of the device

may affect its security, please contact the Legrand customer service team at 1-800-879-8585 / https://www.legrand.us/support/

Wattstopper.aspx

IS-00706 – Rev. 7

ENCLOSURE FEATURES / PARTS

1. Enclosure can (includes door), order LCAP32/44 for can only, (44” shown)

2. Panel Insert (See Panel Load Section)

a. Ground terminals (terminals for upper and lower sections)

b. Module Panel Boards – 103160-1. Up to 4 modules for 44” and up to 2 Modules for 32”

c. Metal isolation barrier between varying voltages. Should be added in Design Center’s project design as part of enclosure

setup, giving it the correct part number via the position (optional)

d. AC Terminal boards installed for module type ordered

e. Terminal board jumpers are installed for lighting control via breakers during construction

NOTE: MDR8CW301 commercial modules do not support either type of terminal jumper boards

3. Panel Insert (controller section)

a. Barrier for IC-36-II controller or secondary terminal board.

b. IC-36-II board or secondary terminal board inside barrier.

c. IC-36-II controller for M models or Secondary Terminal Board for S models.

4. Enclosure cover, with hinged/vented door allowing easy access when servicing and proper ventilation for convection cooling

process

LCAP32/44M/S PANEL BASIC CONSTRUCTION PARTS

IS-00706 – Rev. 7

TERMINAL JUMPER BOARDS

MODULE TERMINAL BOARDS

LCAP32/44M PANEL OPTIONAL CONSTRUCTION PARTS

INSTALLATION / ENCLOSURE MOUNTING INSTRUCTIONS

Terminal jumper boards are installed for use

during construction to supply power to loads.

Modules can then be installed when construction

is nished.

NOTE: 8 line feed relay modules do not have a

jumper board option

JUMPER BOARDS: MJTB or QJUMPER

VOLTAGE BARRIER

When adjacent modules use different line voltage

feeds (e.g., 120V and 277V) install a voltage

barrier between the modules

Installation of LCAP products should be performed or supervised by a Wattstopper/Vantage factory representative and a Certied

Wattstopper/Vantage Installer. Installation and maintenance of high-voltage devices should only be performed by qualied and

licensed personnel having appropriate training and experience.

• The AD-RRU-X-UNV Switch comes pre-installed in the kit

• The AD-EPC-D-F-ATS Switch is installed on site

NOTE: Please see install sheets for emergency switch applications

12 LOAD

TSDM-KIT

8 LOAD

TLM-KIT

8 LOAD

TUDM-KIT

8 LINE FEED

T8LRM-KIT

EMR SWITCH

AD-RRU-X-UNV

EMR SWITCH

AD-EPC-D-F-ATS

Order Separate

EMERGENCY

POWER

UTILITY

POWER

TEST

IS-00706 – Rev. 7

• Do not use outdoors

• Do not mount near gas or electric heaters

• Do not mount enclosures in attics, garages, or crawlspaces, unless room is properly conditioned to conform to ambient room

temperature and humidity requirements

• Mount enclosure a minimum of 18” from ceiling or oor

• National Electrical Code requires a minimum frontal clearance of 36” for the enclosure

• Use screws provided for mounting

• If any emergency circuits are fed or controlled from this panel, it must be located electrically where fed from a UPS, generator, or

other guaranteed source of power during emergency and power outage situations

• LISTED AS EMERGENCY LIGHTING EQUIPMENT – using an appropriate label

• CAUTION: To avoid electrical overload, total external connected load should not exceed output rating

• SAVE THESE INSTRUCTIONS

IMPORTANT SAFEGUARDS

CAUTION: TURN BREAKERS OFF AND CHECK THAT NO POWER IS ON AT THE AC TERMINAL

BOARDS WHEN WORKING IN THE ENCLOSURE OR WORKING ON LIGHTING FIXTURES

CONNECTED TO THE MODULE’S LOADS, ETC. DO NOT ALLOW TRIMMED WIRE CUTTINGS

TO FALL INTO ENCLOSURE COMPONENTS AS THEY MAY CAUSE DAMAGE WHEN

POWER IS RESTORED. DAMAGE FROM THIS TYPE OF SHORT WILL VOID THE WARRANTY.

EMERGENCY CIRCUITS

Drill proper size holes in can for running wires in and out of the enclosure. Separate high and low-voltage wire run

channels. All wire runs in and out of the enclosure should be secured using 2-screw connectors or equivalent as shown

at the right. Proper conduit or equivalent wire channels should be used according to local codes and regulations.

BREAKER FEEDS TO CONTROLLERS

The Controller’s power supply should be wired to a dedicated circuit breaker. When multiple enclosures containing controllers are in

close proximity to one another, it is recommended to share the same breaker to all Main Controllers; no more than nine controllers

may be connected to a 20amp breaker – allow up to 200W@120VAC per InFusion Controller. Do not share the same breaker with

controllers and modules. Please see Main Lug / Circuit Breaker options on page 7.

MAIN CONTROLLER TO MAIN CONTROLLER WIRING

NOTE: the use of Ethernet connections for Controller to Controller communication is recommended. Please see the InFusion

Controller instruction sheet for additional information.

When connecting multiple Main enclosures via the Main Enclosure Terminal Board’s Controller Bus screw terminals, it is

recommended to use station bus wire mentioned below or an equivalent between enclosures. This is a polarized connection with two

“+” and two “–” screw terminals for in and out wire runs. The maximum wire length for all controllers connected together on one bus

should not exceed 2,000ft. using the Station Bus wire specication.

STATION BUS WIRE SPECIFICATION

Vantage wire, part #VDA-0143-BOX or VPLENUM-CABLE – 2C, 16AWG / 1.31mm2, twisted, non-shielded, <30pF per foot. Separate

a minimum of 12” / 30.5cm from other parallel communication and/or high-voltage runs.

STATION BUS WIRING

WireLink stations connect to the Station Bus screw terminals on the Main Enclosure Terminal Board. Use station bus wire, (above).

Maximum total station bus wire for each run = 2,000 feet with no station more than 1,000 feet from enclosure (typically the second

half of the station bus loops back to enclosure with only one end connected). Station Bus should be separated a minimum of 12” from

other parallel communication and/or high-voltage runs.

Connector Torque Wire Range

Module Terminal 20 Inch Pounds 14-10 AWG*

Controller Power 20 Inch Pounds 14-10 AWG*

PROPER HIGH-VOLTAGE TERMINATIONS / PROPER TORQUE

GENERAL WIRING

WIRING

IS-00706 – Rev. 7

MAIN & SECONDARY ENCLOSURE TO SECONDARY ENCLOSURE WIRING

Connecting a Main enclosure to a Secondary enclosure or Secondary enclosure A to Secondary enclosure B, requires 16/18-gauge

4-conductor twisted, non-shielded wire. Three of the wires are always used to connect a Main enclosure to a Secondary enclosure

and chained secondary enclosures. This is a polarized connection with “+”, “–” and “Gnd” screw terminals for communication. The 4th

wire is for Manual Override and is optional. Each Secondary enclosure bus can support two Secondary enclosures for a maximum

of six Secondary enclosures per Main enclosure (see InFusion wiring below). Maximum wiring distance from Main enclosure to

Secondary enclosure is 200ft including an A/B Secondary system (e.g., 100ft from Main enclosure to Secondary enclosure A and an

additional 100ft from Secondary enclosure A to Secondary enclosure B).

MAIN TERMINAL BOARD TERMINATOR

If only one or two Main enclosures are used, the Controller Bus Termination switch must be ON. This switch is located on the

Enclosure Terminal Board. If more than two Main enclosures are used ONLY the rst and last Enclosure Terminal Boards on each

controller bus should have the Network Termination switch set to ON.

RS-232 (PORTS 1-5) FOR MAIN ENCLOSURES

The Main Enclosure Terminal Board has ve RS-232 ports. Use these ports to connect any device that uses RS-232 communication.

Only connect one RS-232 device at a time to an RS-232 port. If additional RS-232 ports are needed, Vantage also manufactures an

RS-232 Station or, some products like the IRX II, have built-in RS-232 ports.

Controller’s serial communication typically use RX, TX and GND for communication but also supports RTS and CTS for some

applications on RS-232 Ports 1 and 2. RS-232 Ports 3-5 only have TX, RX and GND., however, all ve ports can use software ow

control. The default communication protocol may be changed through Design Center software.

Communication protocol parameter settings:

• Standard baud rates 1200 – 115.2K

• 7-8 Data Bits

• Even, Odd, Forced or No Parity

• 200ft. maximum wiring distance

Default protocol for RS-232 communication is:

• Baud: 19200

• Parity: None

• Total bits: 8

• Stop bits: 1

RS-485 CONNECTIONS

The Main Enclosure Terminal Board has two RS-485 ports. These ports are connected to the same screw terminals used for

Secondary enclosure ports 3 and 4. The ports may not be used for Secondary enclosure support and RS-485 support simultaneously.

However, if Secondary enclosure bus ports 3 and/or 4 are free they may be used as RS-485 communication ports. The RS-485 ports

are half-duplex, meaning that each port can transmit and receive but not at the same time. Maximum wiring distance for RS-485 ports

is 200ft.

POSSIBLE GROUND LOOP ISSUES

All RS-232/RS-485 connections between third party equipment and RS-232/RS-485 connections on the Main Enclosure Terminal

Board may produce a ground loop. Most often, the connected RS-232/RS-485 device is not using the same power source or is far

away from the enclosure resulting in a possible ground loop that may produce a data noise condition. If this condition is suspected,

Recommended: A third party RS-232/RS-485 Opto (optical) Isolation Module. Opto Isolation provides a communications link and is

an important consideration if a system uses different power sources, has noisy signals or must operate at different ground potentials.

AUXILIARY POWER

The enclosure, Main Enclosure Terminal Board has a 12VDC auxiliary power connection. The 12VDC connection is typically used for

one RFE1000 RadioLink Enabler or one RFLC-V232 Enabler. Total power is limited to 250ma. NOTE: Do not connect more than one

auxiliary device at a time to this power source. If additional powered devices are needed they must be separately powered with an

external, isolated type (usually no ground prong), power transformer.

WIRING (continued)

IS-00706 – Rev. 7

MANUAL OVERRIDE

In the unlikely event of a Main Controller failure, the Manual Override can be used to turn selected loads ON. If the system is in

override, individual loads can be controlled by dip-switches located on each module in the enclosure. Manual Override control can be

extended to other enclosures. It is common to extend Manual Override between a Main enclosure and its Secondary enclosures. It is

not recommended to extend Manual Override between Main enclosures.

WIRING AC TERMINALS

Keep breaker and load wire runs organized and managed as illustrated.

WIRING (continued)

LCAP32/44M/S SUPPORTED MODULE TYPES

NEUTRALS

Run a separate NEUTRAL for each load connected to dimming

devices. Failure to do this may cause loads, sharing the same

neutral, to icker slightly while ramping or dimming a load. The

potential for ickering occurs with all dimming systems due to the

changing load level coupling to the xed load through the neutral.

MUST MATCH BREAKER WIRE GAUGE

TORQUE: 20 inch pounds

PROPER: Insulation not

cut back too far

PROPER: Wire not forced

in screw terminal too far

SDM12-EM

4 LINE FEED 12 LOAD

STANDARD DIMMER

FANMOD

CEILING FAN MODULE

120V

MDR8CW301

8 LINE FEED 8 LOAD

RELAYS

UDM08-EM

4 LINE FEED 8 LOAD

UNIVERSAL DIMMER

INSTALL INSTRUCTIONS

Click on module names for install instructions.

IS-00706 – Rev. 7

manual

override

NOTE: The InFusion Controller plugs

into the Main Enclosure Terminal Board

after all connections have been made

WIRE TYPES WIRING KEY

6C 18-24AWG

2C 18-16AWG

4C 18AWG

RS232 Ports, Flow Control

RS232 Ports, Flow Control Via Software

Previous Controller Bus

Next Controller Bus

Station Bus Run-1

Station Bus Run-2

To Secondary Enclosure Board (S) Switch

RS485 Ports (If not used for Secondary Bus)

• See maximum wire lengths above •

TORQUE: 20 Inch Pounds

WIRE RANGE: 14-10 AWG*

* Must match breaker wire gauge

LCAPM ENCLOSURE TERMINATIONS

InFusion Main Controller Enclosure Terminations

CAUTION: FOR RETROFIT JOBS, THIS BOARD IS ALSO AVAILABLE IN A 24V VERSION

FOR THE IC-24-II CONTROLLER. NEVER CONNECT STATIONS THAT DO NOT DISPLAY

A CIRCLE SYMBOL ON THE SERIAL NUMBER STICKER TO AN IC-36-II SYSTEM.

IS-00706 – Rev. 7

LCAPS ENCLOSURE TERMINATIONS

INFUSION OVERRIDE WIRING EXAMPLES

InFusion Secondary Enclosure Terminations

InFusion Looped Enclosure Manual Override

Secondary Enclosure

Terminal Board

Enclosure

Select

Enclosure

Bus

Termination

OVERRIDE

SWITCH

IS-00706 – Rev. 7

INFUSION OVERRIDE WIRING EXAMPLES

InFusion Individual Enclosure Manual Override

Secondary Enclosure

Terminal Board

Enclosure

Select

Enclosure

Bus

Termination

OVERRIDE

SWITCH

OVERRIDE

SWITCH

NO CONNECT

to Secondary Enclosure

Terminal Board

IS-00706 – Rev. 7

Secondary Enclosure

Terminal Board

Enclosure

Select

Enclosure

Bus

Termination

Secondary Enclosure

Terminal Board

Enclosure

Select

Enclosure

Bus

Termination

Secondary Enclosure

Terminal Board

Enclosure

Select

Enclosure

Bus

Termination

Secondary Enclosure

Terminal Board

Enclosure

Select

Enclosure

Bus

Termination

Secondary Enclosure

Terminal Board

Enclosure

Select

Enclosure

Bus

Termination

Secondary Enclosure

Terminal Board

Enclosure

Select

Enclosure

Bus

Termination

INFUSION MAIN ENCLOSURE TO SECONDARY ENCLOSURES WIRING OVERVIEW

Note the position of the enclosure selecet switch and the Enclosure Bus Termination switch on each Secondary Enclosure Terminal

Board. All “A” boards are homerun to the Controller board and all “B” boards are homerun to its parent, “A” board. The termination

switch is OFF for all “A” boards only if they have a “B” board connected. The termination switch is ON for all “B” boards.

JUNCTION FOR ALL OVERRIDES

It is also possible to extend

Override from one Secondary

Enclosure to the next Secondary

Enclosure, as long as it daisy

chains back to the Main Enclosure

IS-00706 – Rev. 7

MULTI-VIEW LINE DRAWINGS

44.5” / 113cm

24” / 61cm

4.575”

11.6cm

LCAP44M/S

SIDE PANEL FRONT BACK

32” / 81cm

24” / 61cm

4.575”

11.6cm

ENCLOSURE MULTI-VIEW

LCAP32M/S

ENCLOSURE MULTI-VIEW

SIDE PANEL FRONT BACK

IS-00706 – Rev. 7

ORDERING KEY FOR LCAP32/44M/S

LCAP32/44M/S/LO/CB PANELS WITH MAIN LUG PANEL OPTION

PART #S FOR MODULES / MODULE PLACEMENT

KIT PART

NUMBER

CONTENTS

LCAP32M-KIT

Included (1) LCAP32M Panel with (2) 103160-1 Module boards,

(1) IC-36-II Controller

Optional (1) Module model in locations 1 and 2,

(1) COM-HV-BARRIER Voltage barrier, and

(1) VA-RRU-1-120V or VA-RRU-1-277V

LCAP32S-KIT

Included (1) LCAP32S Panel with (2) 103160-1 Module boards,

(1) Secondary enclosure terminal board

Optional (1) Module model in locations 1 and 2,

(1) COM-HV-BARRIER voltage barrier, and

(1) VA-RRU-1-120V or VA-RRU-1-277V

LCAP44M-KIT

Included (1) LCAP44M Panel with (4) 103160-1 Module boards,

(1) IC-36-II Controller

Optional (1) Module model in locations 1, 2, 3, and 4,

(1) COM-HV-BARRIER Voltage barrier, and

(1) VA-RRU-120V or VA-RRU-1-277V

LCAP44S-KIT

Included (1) LCAP44S Panel with (4) 103160-1 Module boards,

(1) Secondary Enclosure Terminal Board

Optional (1) odule model in locations 1, 2, 3, and 4,

(1) COM-HV-BARRIER Voltage barrier, and

(1) VA-RRU-1-120V or VA-RRU-1-277V

Module Model: Select one module for each location

Replace the asterisk with one of the following:

C - For MDR8CW301, Relay Module, 8-Line Feed 120V-277V

FA - For FANMOD Ceiling Fan Module - 120V

F - For SDM12-EM, Standard Dimming Module - 120V-277V

forward phase)

U - For UDM08-EM Universal Dimming Module - 120V-277Vx

(forward or reverse phase)

X - Blank module position

(Allowed only after populated module positions)

LCAP32M or S - Support for up to 2 modules

LCAP44M or S - Support for up to 4 modules

MAIN LUG CIRCUIT BREAKER OPTION

The LCAPM and LCAPA series enclosures can be congured as a load feed through panels (LCAP PANEL only) or as main lug

panels with the addition of load circuit breakers below the load control feed through compartment. Main lug options can also contain

a main breaker. The Main Lug option is available for the LCAP-M/S and LCAP-A series panels – click to see the LCAP44A/S/LO/

CB install sheet. The circuit breaker options are based on the panel size, number and type of loads, and circuit breaker rating

requirements. Once the main lug panel and circuit breaker options are selected the panel is built and prewired* in the factory and

delivered to the project ready to be installed.

NOTE: Panels With GFI Breakers: GFI breakers are not installed or pre-wired and are shipped separately.

IS-00706 – Rev. 7

LCAP32/44M/S/LO/CB PANELS WITH MAIN LUG PANEL OPTION (continued)

SETUP IN DESIGN CENTER

APPLICATIONS

The LCAP32M/S and 44M/S are designed for medium to large spaces requiring control of up to 48 separate line voltage lighting

circuits. The built-in integration and networking capabilities of the LCAP32M and LCAP44M easily meet requirements in spaces

with shades, comfort control needs, lighting, and other automation integration systems using this panel. Adding an Equinox 41 or

73 touchscreen to the project allows the facility manager or end user to create, change, and manage scenes, schedules, and user

proles.

FEATURES

• Modular LCAP load section; pre-congured solution from the factory. Just connect line voltage and load wires

• Pre-congured Main Lug Panel solution options

• System is expandable using other LCAP series primary or secondary panels and LCAP Main Lug / Circuit Breaker options

• Can be congured with additional emergency rated relays for emergency lighting

• When connected to the local LAN the panel can be remotely programmed

• Low-voltage 2 wire station bus for connecting keypads can extend up to 4,000 ft.*

• Connects to DLM systems for a whole building control solution

• Ability to integrate plug load

• DMX-DALI supported with additional hardware (see DMXDALI-GW)

• Daylight and occupancy sensors are connected to keypads or contact input stations. No power packs needed

• Dimmers have programmable start/stop and dimming curve adjustment features to customize dimming linearity

• Forward phase and reverse phase dimmers are available; SDM12/forward phase and UDM08/forward and reverse phase, each

have 65kA ratings

• Simple programming from a single software solution - Design Center

• LCAP32M and LCAP44M include controller, add up to six LCAP32S or LCAP44S panels for expansion of dimming and load

control capabilities; network additional controllers for further scalability

• One LCAP32/44M series enclosure supports up to six additional LCAP32S and LCAP44S panels for expansion of dimming and

load control capabilities. LCAP32M and LCAP44M series support up to 30 additional M-series enclosures with controllers for

almost unlimited scalability

• Adding one BACnet enabled controller to a system allows the entire system to be controlled through BACnet

• Main Lug Panel options range from 18 to 36 circuits, 208-480V, and 10kAIC to 65kAIC and may be congured with a main

breaker option

UNDERSTANDING LCAP AND MAIN LUG PANELS

• LCAP panels with the Main Lug option is a larger enclosure that holds the traditional

LCAP components in the upper section of the enclosure and includes a breaker

section in the lower section of the enclosure.

• LCAP panels with the Main Lug option are built in Design Center the same way as

standard LCAP panels. The only difference is the Main Lug option has been selected.

Follow the steps below to create an LCAP panel with the Main Lug option selected.

1. In Design Center | Object Explorer select:

• Vantage Objects,

• Enclosures, Commercial,

• LCAP model:

• LCAP32-44M/S-KIT (Main Lug)

Set module count to two (2) for LCAP32/M

- or -

Set module count to four (4) for LCAP44/M

• Select model LCAP 44A-KIT (Main Lug) - see LCAP44A install

2. Right click in the enclosure and select Populate to automatically add modules in the

enclosure or select modules and drag into the enclosure as wanted. (It is not possible

to drag a module below a blank module location in an LCAP enclosure – ll enclosure

from top to bottom).

IS-00706 – Rev. 7

SETUP IN DESIGN CENTER (continued)

LCAP32/44M/S/LO/CB SERIES SPECIFICATIONS

3. Notice that breakers are automatically added to the Main Lug section of the enclosure as modules are added.

4. It is possible to add additional breakers in the Main Lug section by right clicking below existing breakers and selecting Add

Breaker until the maximum number of breakers allowed is reached.

5. Select the Main Lug section of the enclosure and change the type to MCB to add a Main Breaker option or leave as MLO for

standard load breakers only.

Specications LCAP32/M/S/LO LCAP32/M/S/CB LCAP44/M/S/LO LCAP44/M/S/CB

Cabinet / Panel Cover

Dimensions - HWD

55.5” x 24” x 4.75”

140.97cm x 60.96cm x

12.06cm

64.5” x 24.0” x 4.75”

163.83cm x 60.96cm x

12.06cm

68.0” x 24.0” x 4.75”

172.72cm x 60.96cm x

12.06cm

77.0” x 24.0” x 4.75”

195.58cm x 60.96cm x

12.06cm

LCAP Panel Door

Dimensions - HWD

28” x 16” x 0.75”

71.12cm x 40.64cm x 1.9cm

40.5” x 16.0” x 0.75”

102.87cm x 40.64cm x 1.9cm

Panel Insert - HWD 29.5” x 21” x 4.175”

75cm x 53.3cm x 10.6cm

42” x 21” x 4.175”

106.7cm x 53.3cm x 10.6cm

Weight - Panel Insert M-18.7 lbs. 8.48 kg

S-15.4 lbs. 6.99 kg

M-23 lbs. 10.43 kg

S-20 lbs. 9.07 kg

Number of Modules Up to 2 Up to 4

Load Capacity Up to 24 Up to 48

Line Feeds Up to 17 Up to 33

Breakers Up to 18 Up to 36

Main Lug Panel Door

Dimensions - HWD

16” x 12.5” x 0.75”

40.64cm x 31.75cm x

1.9cm

23” x 12.5” x 0.75”

58.42cm x 31.75cm x

1.9cm

16” x 12.5” x 0.75”

40.64cm x 31.75cm x

1.9cm

23” x 19” x 0.75”

58.42cm x 48.26cm x

1.9cm

Weight - Enclosure

with Cover

110 - 130 lbs / 49.9 -

58.97 kg

115 - 135 lbs / 52.16 -

61.23 kg

165 - 175 lbs / 74.84 –

79.38 kg

170 - 180 lbs / 77.11 –

81.65 kg

*Flash Memory (via controller)

Enclosure Finish Galvanized Steel

Door Finish Black - Poweder Coated

Cover Vented, hinged

Wire Copper wire, MIN. of 80°C / 176°F insulation

Ventilation Maintained 36” front clearance

Ambient Operating

Temperature

0-40°C / 32-104°F

Ambient Operating

Humidity

5-95% non-condensing

UL, CUL, and CE

Listed

Yes

IS-00706 – Rev. 7

STANDARD LCAPM SERIES AND LCAPA SERIES ENCLOSURES WITH MAIN LUG ENCLOSURES

LCAP32M/S CONFIGURED WITH LCAP32/M/LO/CB EXAMPLE:

LCAP44M/S CONFIGURED WITH LCAP44/M/LO/CB EXAMPLE:

LCAP32M/S

• Main Lug options LO or CB come

with (up to) 18, 20A breakers

• Finished LCAP32/LO enclosure:

55.5” high

• Finished LCAP32/CB enclosure:

64.5” high

• See additional specications on pg

15 and drawings on pg 17

LCAP32M/S

• Main Lug options LO or CB come

with (up to) 18, 20A breakers

• Finished LCAP44/LO enclosure:

68” high

• Finished LCAP44/CB enclosure:

77” high

• See additional specications on pg

15 and drawings on pg 17

IS-00706 – Rev. 7

COMMUNICATION CONDUIT

GROUND BAR

NEUTRAL

BAR

CIRCUIT

BREAKERS

DIMMER

SECTION

BARRIER

COMMUNICATION

CONDUIT

GROUND BAR

CIRCUIT

BREAKERS

NEUTRAL

BAR

BARRIER

DIMMER

SECTION

208Y/120V 30 4W

(10KAIC-22KAIC-65KAIC)

LCAP32 PANEL SURFACE TRIM

BOX 4 1/2” DEEP

WITH DOORS INSTALLED

LCAP32 PANEL

MAIN LUGS WITH DOORS

& DEADFRONT REMOVED

LCAP32 PANEL SURFACE MOUNT

BOX 4 1/2” DEEP

WITH DOORS INSTALLED

LCAP32 PANEL

MAIN BREAKER WITH DOORS

& DEADFRONT REMOVED

480Y/277V 30 4W

(14KAIC)

120V/240V 10 3W

(10KAIC-22KAIC-65KAIC)

BUS DIAGRAMS

100A MAIN LUGS

100A

MAIN

BKR.

208Y/120V 30 4W

(10KAIC-22KAIC-65KAIC)

480Y/277V 30 4W

(14KAIC-*35KAIC-*65KAIC)

*SERIES RATED

120V/240V 10 3W

(10KAIC-22KAIC-65KAIC)

BUS DIAGRAMS

100A MAIN BREAKER

24.0” (60.96cm)

32.25” (81.915cm) 23.25” (59.055cm)

4.5” (11.43cm)

32.25” (81.915cm) 32.25” (81.915cm)

55.5” (140.97cm)

64.5” (163.83cm)

100A

MAIN

BKR.

LCAP32M/S/LO

1. Enclosure upper section for

LCAP32M/S Panel

2. Enclosure lower section for

up to 18 breakers. Select the

Main Lug option MLO option

for (up to) 18, 20A breakers

3. Breaker section may be

congured for 4-wire or

3-wire power congurations

4. See last page for breaker/

order options

LCAP32M/S/CB

1. Enclosure upper section for

LCAP32M/S Panel

2. Enclosure lower section for

up to 18 breakers. Select

the Main Lug type and

change to MCB to add a

Main Breaker option

3. Breaker section may be

congured for 4-wire or

3-wire power congurations

4. See last page for breaker/

order options

LCAP32M/S/LO WITH MAIN LUG ENCLOSURE MULTI-VIEW

LCAP32M/S/CB WITH MAIN LUG/ MAIN BREAKER ENCLOSURE MULTI-VIEW

LCAP44M/S/LO WITH MAIN LUG ENCLOSURE MULTI-VIEW

DIMMER

SECTION

DIMMER

SECTION

LCAP44 PANEL SURFACE TRIM

BOX 4 1/2” DEEP

WITH DOORS INSTALLED

LCAP44 PANEL

MAIN LUGS WITH DOORS

& DEADFRONT REMOVED

208Y/120V 30 4W

(10KAIC-22KAIC-65KAIC)

480Y/277V 30 4W

(14KAIC)

120V/240V 10 3W

(10KAIC-22KAIC-65KAIC)

BUS DIAGRAMS

100A MAIN LUGS

100A

MAIN

BKR.

208Y/120V 30 4W

(10KAIC-22KAIC-65KAIC)

480Y/277V 30 4W

(14KAIC-*35KAIC-*65KAIC)

*SERIES RATED

120V/240V 10 3W

(10KAIC-22KAIC-65KAIC)

BUS DIAGRAMS

100A MAIN BREAKER

4.5” (11.43cm)

23.25” (59.055cm)

CIRCUIT

BREAKERS

BARRIER

100A

COMMUNICATION CONDUIT

GROUND BAR

NEUTRAL

BAR

44.75” (113.665cm)

68” (172.72cm)

24.0” (60.96cm)

LCAP44-18 PANEL SURFACE

MOUNT BOX 4 1/2” DEEP

WITH DOORS INSTALLED

LCAP44-18 PANEL

MAIN BREAKER WITH DOORS

& DEADFRONT REMOVED

4.5” (11.43cm)

CIRCUIT

BREAKERS

BARRIER

COMMUNICATION CONDUIT

GROUND BAR

NEUTRAL

BAR

77” (195.58cm)

24.0” (60.96cm)

32.25” (81.915cm)44.75” (113.665cm)

MAIN

BKR.

LCAP44M/S/LO

1. Enclosure upper section for

LCAP44M/S Panel

2. Enclosure lower section for

up to 18 breakers. Select the

Main Lug option MLO option

for (up to) 18, 20A breakers

3. Breaker section may be

congured for 4-wire or

3-wire power congurations

4. See last page for breaker/

order options

LCAP44M/S/CB

1. Enclosure upper section for

LCAP44M/S Panel

2. Enclosure lower section for

up to 18 breakers. Select

the Main Lug type and

change to MCB to add a

Main Breaker option

3. Breaker section may be

congured for 4-wire or

3-wire power congurations

4. See last page for breaker/

order options

LCAP44M/S/CB WITH MAIN LUG/MAIN BREAKER ENCLOSURE MULTI-VIEW

IS-00706 – Rev. 7

LCAP44M/S/CB

1. Enclosure upper section for LCAP44M/S Panel

2. Enclosure lower section for up to 36 breakers. Select the Main

Lug type and change to MCB to add a Main Breaker option

3. Breaker section may be congured for 4-wire or 3-wire power

congurations

LCAP44M/S/LO/36 BREAKERS WITH MAIN LUG ENCLOSURE MULTI-VIEW

LCAP44M/S/CB/36 BREAKERS WITH MAIN LUG/MAIN BREAKER ENCLOSURE MULTI-VIEW

LCAP44M/S/LO

1. Enclosure upper section for LCAP44M/S Panel

2. Enclosure lower section for up to 36 breakers.

Select the Main Lug option MLO option for (up to)

18, 20A breakers

3. Breaker section may be congured for 4-wire or

3-wire power congurations

4. See last page for breaker/order options

DIMMER

SECTION

BREAKER

SECTION

DIMMER

SECTION

BREAKER

SECTION

208Y/120V 30 4W

(10KAIC-22KAIC-65KAIC)

480Y/277V/30 4W

(14KAIC)

120V/240V 10 3W

(10KAIC-22KAIC-65KAIC)

BUS DIAGRAMS

100A MAIN LUGS

LCAP44-36 PANEL SURFACE

MOUNT BOX 4 1/2” DEEP

WITH DOORS INSTALLED

LCAP44-36 PANEL

MAIN BREAKER WITH DOORS

& DEADFRONT REMOVED

4.5” (11.43cm)

CIRCUIT

BREAKERS

BARRIER

COMMUNICATION

CONDUIT

NEUTRAL BAR

GROUND

BAR

77” (195.58cm)

24.0” (60.96cm)

32.25” (81.915cm)44.75” (113.665cm)

LCAP44-18 PANEL SURFACE

MOUNT BOX 4 1/2” DEEP

WITH DOORS INSTALLED

LCAP44-18 PANEL

MAIN BREAKER WITH DOORS

& DEADFRONT REMOVED

4.5” (11.43cm)

CIRCUIT

BREAKERS

BARRIER

COMMUNICATION CONDUIT

GROUND BAR

NEUTRAL

BAR

77” (195.58cm)

24.0” (60.96cm)

32.25” (81.915cm)44.75” (113.665cm)

225A

100A

MAIN

BKR.

208Y/120V 30 4W

(10KAIC-22KAIC-65KAIC)

BUS DIAGRAMS

100A - 225A

MAIN BREAKER

480Y/277V 30 4W

(14KAIC-*35KAIC-*65KAIC)

*SERIES RATED

NEUTRAL

225A

100A

MAIN

BKR.

120V/240V 10 3W

(10KAIC-22KAIC-65KAIC)

NEUTRAL

IS-00706 – Rev. 7

CONFIGURATION FOR LCAP32 ADDER - Branch Breakers Each, 1-Pole, 20A

SIZE HEIGHT BASE PANEL CONFIGURATION 10kAIC 14kAIC

11kAIC 35kAIC 65kAIC

18 Circuits

100A

Bussing

56”

240V - MLO (Single Phase) BAB

QHB GHB

208V - MLO BAB

QHB GHB

480V - MLO GHB

65”

240V - MCB (Single Phase) (Up to 100A, 65kAIC)

BAB*

208V - MCB (up to 100A, 65kAIC)

BAB*

480V - MCB (up to 100A, 35kAIC)

GHB*

480V - MCB (up to 100A, 65kAIC)

GHB*

CONFIGURATION FOR LCAP44 ADDER - Branch Breakers Each, 1-Pole, 20A

SIZE HEIGHT BASE PANEL CONFIGURATION 10kAIC 14kAIC

11kAIC 35kAIC 65kAIC

18 Circuits

100A

Bussing

68”

240V - MLO (Single Phase) BAB

QHB GHB

208V - MLO BAB

QHB GHB

480V - MLO GHB

77”

240V - MCB (Single Phase) (Up to 100A, 65kAIC)

BAB*

208V - MCB (up to 100A, 65kAIC)

BAB*

480V - MCB (up to 100A, 35kAIC)

GHB*

480V - MCB (up to 100A, 65kAIC)

GHB*

CONFIGURATION FOR LCAP44 - 36 BREAKER ADDER - Branch Breakers Each, 1-Pole, 20A

SIZE HEIGHT SIZE 10kAIC 14kAIC

11kAIC 35kAIC 65kAIC

18 Circuits

100A

Bussing

77”

240V - MLO (Single Phase) BAB

QHB GHB

208V - MLO BAB

QHB GHB

480V - MLO GHB

240V - MCB (Single Phase) (Up to 225A, 65kAIC)

BAB*

208V - MCB (up to 225A, 65kAIC)

BAB*

480V - MCB (up to 100A, 35kAIC)

GHB*

480V - MCB (110A - 225A, 35kAIC)

GHB*

480V - MCB (up to 100A, 65kAIC)

GHB*

480V - MCB (100A - 225A, 65kAIC)

GHB*

BREAKER RATING LEGEND (Single Phase)

MLO = Main Lug Option Type BAB 10kAIC

MCB = Main Lug with Main Circuit Breaker Type QBH 22kAIC

208V - MLO BAB

LCAP WITH OPTIONAL MAIN LUG PART NUMBER ORDERING KEY

Design Center will generate LCAP32/34/M/S/LO/CB part numbers automatically as the enclosures are built. This key is for help in

understanding and creating orders in the LCAP Quote Tool online ordering tool.

BREAKER TYPES FOR LCAPM/S/LO/CB ENCLOSURE CONFIGURATIONS

Page is loading ...

Legrand LCAP32M Installation guide

Legrand LCAP32M Installation guide

Legrand LCAP32M Installation guide

Related papers

Other documents