H3C WX5004 Installation guide

H3C WX5004 Access Controller

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6PW101-20130128

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

3

Care,

, IRF, NetPilot, Netflow,

SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of

Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage,

use, and disposal of this product must meet the applicable national laws and regulations.

About This Manual

Organization

The H3C WX5004 documentation set includes:

Category Documents Purposes

Marketing brochures Describe product specifications and benefits.

Product description and

specifications

Technology white

papers

Provide an in-depth description of software

features and technologies.

Compliance and safety

manual

Provides regulatory information and the safety

instructions that must be followed during

installation.

Hardware

specifications and

installation

Installation guide

Provides a complete guide to hardware

installation and hardware specifications.

Configuration guides

Describe software features and configuration

procedures.

Command references

Provide a quick reference to all available

commands.

Software configuration

Configuration

examples

Describe typical network scenarios and provide

configuration examples and instructions.

Operations and

maintenance

Release notes

Provide information about the product release,

including the version history, hardware and

software compatibility matrix, version upgrade

information, technical support information, and

software upgrading.

Conventions

The manual uses the following conventions:

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in

Boldface. For example, the New User window appears; click OK.

>

Multi-level menus are separated by angle brackets. For example, File >

Create > Folder.

Convention Description

< > Button names are inside angle brackets. For example, click <OK>.

[ ]

Window names, menu items, data table and field names are inside

square brackets. For example, pop up the [New User] window.

/

Multi-level menus are separated by forward slashes. For example,

[File/Create/Folder].

Symbols

Convention Description

Means reader be extremely careful. Improper operation may cause

bodily injury.

Means reader be careful. Improper operation may cause data loss or

damage to equipment.

Means an action or information that needs special attention to ensure

successful configuration or good performance.

Means a complementary description.

Obtaining Documentation and Technical Support

You can access the most up-to-date H3C product documentation on the World Wide Web at

http://www.h3c.com

.

Click the links on the top navigation bar to obtain different categories of product documentation:

[Technical Support & Documents > Technical Documents]

– Provides hardware installation, software

upgrading, and software feature configuration and maintenance documentation.

[Products & Solutions]

– Provides information about products and technologies, as well as solutions.

[Technical Support & Documents > Software Download]

– Provides the documentation released with

the software version.

Technical Support

service@h3c.com

http://www.h3c.com

Documentation Feedback

You can e-mail your comments about product documentation to [email protected]m.

We appreciate your comments.

i

Table of Contents

1 Access Controller Overview·····················································································································1-1

Introduction ·············································································································································1-1

Appearance·············································································································································1-1

Front Panel ······································································································································1-1

Rear Panel·······································································································································1-2

Specifications ··········································································································································1-3

Processor and Storages··················································································································1-3

Dimensions and Weight···················································································································1-3

Fixed Interfaces and Slots···············································································································1-3

Power Input ·····································································································································1-3

Components············································································································································1-4

LEDs················································································································································1-4

Fixed Interfaces ·······························································································································1-5

Fans·················································································································································1-9

Interface Numbering································································································································1-9

2 Installation Preparation·····························································································································2-1

Safety Precautions ··································································································································2-1

Installation Site Checking························································································································2-2

Requirements on Temperature and Humidity ·················································································2-2

Requirements on Cleanness ···········································································································2-2

Anti-Static Requirements·················································································································2-3

Electromagnetic Environment Requirements ··················································································2-4

Laser Safety ····································································································································2-4

Installation Tools ·····································································································································2-5

3 Installation··················································································································································3-1

Installation Procedure ·····························································································································3-1

Installing the Access Controller onto a 19-Inch Rack ·············································································3-2

Installing the Access Controller with Front and Rear Mounting Brackets ·······································3-2

Installing the Access Controller with Front Mounting Brackets and a Tray·····································3-6

Installing the Access Controller with Mounting Brackets and Slide Rails ·······································3-7

Installing the Access Controller on a Workbench ···················································································3-9

Connecting the Ground Wire ··················································································································3-9

Connecting the Power Cord··················································································································3-11

Connecting the AC Power Cord ····································································································3-11

Connecting the DC Power Cord ····································································································3-12

Connecting Interface Cables·················································································································3-13

Connecting the Console Cable······································································································3-13

Connecting the Ethernet Cable ·····································································································3-14

Checking the Installation·······················································································································3-15

4 Initial Startup··············································································································································4-1

Setting up the Configuration Environment ······························································································4-1

Connecting a Configuration Terminal to the Access Controller ······················································4-1

ii

Setting Terminal Parameters···········································································································4-1

Powering On the Access Controller ········································································································4-3

Checking Before Power-On·············································································································4-3

Powering on the Access Controller ·································································································4-4

5 Software Maintenance·······························································································································5-1

Overview ·················································································································································5-1

Files Managed by the Access Controller·························································································5-1

BootWare Program File···················································································································5-1

Application Files ······························································································································5-1

Configuration Files···························································································································5-2

Approaches for Software Maintenance ···························································································5-3

BootWare and Application File Upgrade Flow ················································································5-4

BootWare Menus ····································································································································5-4

BootWare Main Menu······················································································································5-4

BootWare Submenus ······················································································································5-6

Upgrading the BootWare Through a Ethernet/Serial Interface·······························································5-7

Modifying Serial Interface Parameters ····························································································5-8

Upgrading the BootWare Through an Ethernet Interface······························································5-10

Upgrading the BootWare Through a Serial Interface ····································································5-12

Upgrading Applications Through a Serial Interface on the BootWare Menu········································5-14

Upgrading Applications Through an Ethernet Interface on the BootWare Menu··································5-15

Configuring Ethernet Interface Parameters···················································································5-15

Upgrading Applications Through an Ethernet Interface ································································5-16

Maintaining the Application and Configuration Files Through the CLI··················································5-17

Maintaining the Access Controller Through TFTP ········································································5-17

Maintaining the Access Controller Through FTP ··········································································5-19

Maintaining Application and Configuration Files···················································································5-22

Displaying All Files ························································································································5-22

Setting an Application File Type····································································································5-22

Specifying a Startup Configuration File·························································································5-23

Delete a File ··································································································································5-24

Dealing With Password Loss ················································································································5-24

User Password Loss······················································································································5-25

BootWare Password Loss ·············································································································5-25

Super Password Loss····················································································································5-26

Backing Up and Restoring the BootWare ·····························································································5-26

Using the BootWare Menu ············································································································5-26

Using the CLI·································································································································5-26

6 Troubleshooting ········································································································································6-1

Software Loading Failure ························································································································6-1

Power Supply Failure······························································································································6-1

Configuration System Failure··················································································································6-2

No Display on the Terminal ·············································································································6-2

Illegible Characters on the Terminal································································································6-2

1-1

1 Access Controller Overview

Introduction

The H3C WX5004 Access Controller is a new-generation wireless access controller product developed

by Hangzhou H3C Technologies Co., Ltd. (referred to as H3C hereinafter) based on the updated

multi-core CPU platform. Compared with the WX5002, the previous-generation access controllers, the

WX5004 has two more groups of Combo ports, allowing for more flexible user configurations. Besides,

the WX5004 also provides an expansion slot, where you can insert a card of a different type as needed

in the future. This provides not only strong processing capability but also flexible system configuration

schemes. In terms of reliability, the WX5004 uses pluggable power supply units (PSU). Thus, you can

choose to use double PSUs for high reliability or use a single PSU for economical sake.

Appearance

Figure 1-1 shows the appearance of the WX5004.

Figure 1-1 Appearance of the WX5004

Front Panel

The WX5004 provides four 10/100/1000 Base-T Ethernet electrical interfaces, four 1000 Base-X

Ethernet optical interfaces (Combo ports) and one console port on its front panel, as shown in Figure

1-2.

1-2

Figure 1-2 Front panel of the WX5004

(1) Gigabit Ethernet interface 4—SFP optical interface

(2) 1000 Mbps LED of gigabit Ethernet interface 4

(3) 10/100 Mbps LED of gigabit Ethernet interface 4

(4) 10/100/1000 Base-T auto-sensing Ethernet electrical interface 4

(5) Gigabit Ethernet interface 3—SFP optical interface

(6) 1000 Mbps LED of gigabit Ethernet interface 3

(7) 10/100 Mbps LED of gigabit Ethernet interface 3

(8) 10/100/1000 Base-T auto-sensing Ethernet electrical interface 3

(9) Gigabit Ethernet interface 2—SFP optical interface

(10) 1000 Mbps LED of gigabit Ethernet interface 2

(11) 10/100 Mbps LED of gigabit Ethernet interface 2

(12) 10/100/1000 Base-T auto-sensing Ethernet electrical interface 2

(13) Gigabit Ethernet interface 1—SFP optical interface

(14) 1000 Mbps LED of gigabit Ethernet interface 1

(15) 10/100 Mbps LED of gigabit Ethernet interface 1

(16) 10/100/1000 Base-T auto-sensing Ethernet electrical interface 1

(17) Console port (18) System LED

(19) LED of the expansion card (20) LED of power supply 1

(21) LED of power supply 2

Rear Panel

The WX5004 provides two power supply module slots and one expansion card slot, as shown in Figure

1-3.

Figure 1-3 Rear panel of the WX5004

(1) PSU 1 (AC/DC) (2) Handle of PSU 1

(3) OPEN BOOK sign (4) Power cord retainer for PSU 1

(5) AC power socket of PSU 1 (6) PSU 2 (AC/DC)

(7) Handle of PSU 2 (8) OPEN BOOK sign

(9) Power cord retainer for PSU 2 (10) AC power socket of PSU 2

(11) Expansion card slot (12) OPEN BOOK sign

(13) Grounding screw

OPEN BOOK and CAUTION signs: Refer to related sections when performing the following operations:

1-3

Table 1-1 OPEN BOOK sign description

Operation Related section

Connect the power cord Connecting the AC Power Cord

Ground the device Connecting the Ground Wire

Specifications

Processor and Storages

Table 1-2 Processor and storages of the WX5004

Item Description

Processor XLR716 (800 MHz)

CF card Built in, 256 MB

Memory type and capacity

Memory: DDR2 SDRAM

Capacity: 2048 MB

Dimensions and Weight

Table 1-3 Dimensions and weight

Item Description

Dimensions (H × W × D) 43.6 × 440 × 430 mm (1.72 × 17.32 × 16.93 in.)

Weight 7.4 kg (16.31 lb.) (with two PSUs installed)

Fixed Interfaces and Slots

Table 1-4 Fixed interfaces and slots

Item Description

Console port 1 console port, 9600 bps (the default) to 115200 bps.

Ethernet interfaces

4 × 10/100/1000 Base-T autosensing Layer 2 Ethernet interfaces; support

MDI/MDIX

SFP interfaces

4 × 1000 Base-X SFP optical interfaces, forming Combo ports together with

the corresponding Ethernet electrical interfaces

Slots

z 1 expansion card slot

z 2 PSU slots

Power Input

The WX5004 uses two AC/DC PSUs, which provide 1+1 redundancy backup for the WX5004 to

enhance the system reliability.

1-4

Table 1-5 AC/DC power input

Item Description

Rated voltage range

For AC power input: 100 VAC to 240 VAC, 50 Hz or 60 Hz

For DC power input: –48 VDC to –60 VDC

Max input voltage range

For AC power input: 90 VAC to 264 VAC, 47 Hz to 63 Hz

For DC power input: –36 VDC to –72 VDC

Power consumption 53.4 W to 67.7 W

z You are not recommended to use an AC power module with a DC power module on the device.

z No AC or DC power module is provided with the access controller. You need to prepare them

yourself.

Components

LEDs

The WX5004 provides LEDs on the front panel, as shown in Figure 1-4.

Figure 1-4 LEDs of the WX5004

(4)

(1)

(2)

(5)

(3)

(6)

(1) 1000 Mbps LED of gigabit Ethernet interface (1000M)

(2) System status LED (SYS) (3) Status LED of PSU 1 (PWR1)

(4) 10/100 Mbps LED of gigabit Ethernet interface (10/100M)

(5) LED of the expansion card (MOD) (6) Status LED of PSU 2 (PWR2)

Table 1-6 Description of LEDs

LEDs Silkscreen Status Description

Solid green

PSU 1 supplies power to the system

normally.

Solid yellow PSU 1 is faulty.

LED of PSU 1

(green/yellow)

PWR1

Off No PSU is installed in the slot.

1-5

LEDs Silkscreen Status Description

Solid green

PSU 2 supplies power to the system

normally.

Solid yellow PSU 2 is faulty.

LED of PSU 2

(green/yellow)

PWR2

Off No PSU is installed in the slot.

Solid green

The system is performing POST or

downloading software.

Green, slow

blinking (1 Hz)

The system works normally.

Solid yellow

The POST has failed or another fatal error

has been detected in the system.

System LED

(green/yellow)

SYS

Off No power input

Solid green The expansion card is present in the slot.

LED of the

expansion card

(green)

MOD

Off The expansion card is not present in the slot

Solid green The interface is connected at 1000 Mbps.

Blinking green (6

Hz)

The port is receiving or sending data at 1000

Mbps

1000M

Off

The interface is not connected at 1000

Mbps.

Solid yellow The interface is connected at 10/100 Mbps.

Blinking yellow (6

Hz)

The interface is receiving or sending data at

10/100 Mbps.

Gigabit Combo

port LED

10/100M

Off

The interface is not connected at 10/100

Mbps.

Fixed Interfaces

Console port

The WX5004 provides an RS232 asynchronous serial port (console port) that can be connected to a

computer for system debugging, configuration, maintenance, management, and host software loading.

The console cable is an 8-core cable. One end of the cable is a crimped RJ-45 connector and is

connected to the console port of the WX5004. The other end is a DB-9 female connector and is

connected to the 9-pin serial port on the configuration terminal. Figure 1-5

illustrates a console cable:

Figure 1-5 Console cable

1-6

Table 1-7 Console cable pinouts

RJ-45 Signal Direction DB-9

1 RTS ← 7

2 DTR ← 4

3 TXD ← 3

4 CD → 1

5 GND — 5

6 RXD → 2

7 DSR → 6

8 CTS → 8

Ethernet interfaces

1) Introduction

The WX5004 provides four 10/100/1000 Base-T autosensing Ethernet electrical interfaces and four

1000 Base-X SFP optical interfaces. One electrical interface and one optical interface form a Combo

port, which is marked in a white box on the front panel. Only one interface (either electrical or optical) of

a Combo port can be used at a time.

z Ethernet electrical interfaces support 10/100/1000 Mbps autosensing. Table 1-8 describes the

working mode of the interfaces in each speed.

Table 1-8 Speed and working mode of an electrical Ethernet interface

Speed Working mode

10 Mbps (autosensing) Half/full duplex, auto-negotiation

100 Mbps (autosensing) Half/full duplex, auto-negotiation

1000 Mbps (autosensing) Full duplex, auto-negotiation

z Ethernet optical interfaces support 1000 Mbps full duplex. The optical interface and the electrical

interface of a Combo port share the same LED.

z A Combo port can work in either the electrical interface mode or the optical interface mode, that is,

either the electrical interface or the optical interface of a Combo port can be used at a time.

z A Combo port supports optical-electrical automatic switching, however, when both the optical and

electrical interfaces are connected, the electrical interface will be used in precedence.

2) SFP interface modules

The WX5004 provides four SFP GE optical interfaces. The following SFP modules are available:

z 1000 Base-SX SFP module

1-7

z 1000 Base-LX SFP module

Table 1-9 Technical specifications for the GE optical interface modules

Description

Item

Short-haul

multimode

(850 nm)

SFP module

Medium-haul

single-mode

(1310 nm)

SFP module

Long-haul

single-mode

(1310 nm)

SFP module

Long-haul

single-mode

(1550 nm)

SFP module

Ultra-long-haul

single-mode

(1550 nm)

SFP module

Connector SFP/LC

Optical fiber

62.5 μm/125

μm

multimode

9 μm /125 μm

single-mode

9 μm /125 μm

single-mode

9 μm /125

μm

single-mode

9 μm /125 μm

single-mode

Max.

transmission

distance

0.55 km

(0.34 mi)

10 km (6.21

mi)

40 km (24.86

mi)

40 km (24.86

mi)

70 km (43.50 mi)

Central

wavelength

850 nm 1310 nm 1310 nm 1550 nm 1550 nm

Min. -9.5 dBm -9 dBm -2 dBm -4 dBm -4 dBm Optical

transmit

power

Max. 0 dBm -3 dBm 5 dBm 1 dBm 2 dBm

Receive

sensitivity

-17 dBm -20 dBm -23 dBm -21 dBm -22 dBm

Working mode

1000 Mbps

Full duplex

No SFP module is shipped with the WX5004. You need to purchase SFP modules as needed and are

recommended to use H3C SFP modules.

3) RJ-45 connector

The 10/100/1000 Mbps electrical Ethernet interfaces of the WX5004 use RJ-45 connectors to connect

with the category 5 twisted pair cables. Figure 1-6

shows the appearance of an RJ-45 connector.

Figure 1-6 RJ-45 connector

4) LC connector

Optical fiber connectors are indispensable passive components in optical fiber communication systems.

Their application enables the removable connection between optical channels, which makes the optical

1-8

system debugging and maintenance more convenient and the transit dispatching of the system more

flexible.

The Ethernet optical interfaces of the WX5004 support LC connectors only.

Figure 1-7 LC connector

z Before using an optical fiber to connect a network device, make sure that the optical fiber connector

matches the optical module.

z Before connecting the fiber, make sure that the receiving-end optical power does not exceed the

upper threshold of the receiving optical power. Excessive receiving optical power is very likely to

burn the optical module. For optical power values of the optical modules, refer to Table 1-9

.

5) Ethernet electrical interface cables

Usually, you can use a category-5 twisted pair cable to connect an electrical interface to an Ethernet.

Figure 1-8

shows an Ethernet cable.

Figure 1-8 Ethernet cable

Ethernet cables fall into the following two categories:

z Standard cable: Also called straight-through cable. At both ends of a standard cable, wires are

crimped in the RJ-45 connectors in the same sequence. A straight-through cable is used to

connect a terminal (for example, PC or router) to a Hub or LAN Switch.

z Crossover cable: At both ends of a crossover cable, wires are crimped in the RJ-45 connectors in

different sequences. A crossover cable is used to connect a terminal (for example, a PC or router)

to another terminal. You can make crossover cables by yourself as needed.

Table 1-10 Straight-through cable pinouts

RJ-45 Signal

Category-5

twisted pair

Signal direction RJ-45

1 TX+ White (Orange)

Æ

1

2 TX- Orange

Æ

2

3 RX+ White (Green)

Å

3

4 — Blue — 4

5 — White (Blue) — 5

1-9

RJ-45 Signal

Category-5

twisted pair

Signal direction RJ-45

6 RX- Green

Å

6

7 — White (Brown) — 7

8 — Brown — 8

Table 1-11 Crossover cable pinouts

RJ-45 Signal

Category-5

twisted pair

Signal direction RJ-45

1 TX+ White (Orange)

Æ

3

2 TX- Orange

Æ

6

3 RX+ White (Green)

Å

1

4 — Blue — 4

5 — White (Blue) — 5

6 RX- Green

Å

2

7 — White (Brown) — 7

8 — Brown — 8

z You can refer to the table above when distinguishing between or preparing these two types of

Ethernet cables.

z When preparing Ethernet cables, please follow the chromatogram given in the table to arrange the

wires. Otherwise communication quality will be affected even if the devices at both ends are

connected.

Fans

The WX5004 is equipped with five fans: three fans for heat dissipation of the main board and two fans

for heat dissipation of the expansion card. If no expansion card is installed, these two fans do not work.

Interface Numbering

The WX5004 provides four fixed GE interfaces numbered GigabitEthernet 1/0/1 through

GigabitEthernet 1/0/4, with the last part of the port numbers indicated on the front panel

2-1

2 Installation Preparation

Safety Precautions

Installation and removal of the unit and its accessories must be carried out by qualified personnel. You

must read all of the Safety Instructions supplied with your device before installation and operation.

Installation und Ausbau der Anlage und ihrer Zubehörteile müssen von qualifiziertem Personal realisiert

werden. Sie müssen vor der Installation oder Bedienung allen beiliegenden Sicherheitshinweise lesen.

负责安装和日常维护本设备的人员必须具备安全操作基本技能。在操作本设备前，请务必认真阅读和执

行产品手册规定的安全规范。

To avoid any device impairment and bodily injury caused by improper use, observe these rules:

z Pull the power plug(s) out of the access controller before cleaning it. Do not clean the access

controller using wet cloth or liquid.

z Keep the access controller away from water or dampness. Prevent water or moisture from entering

the chassis of the access controller.

z Do not place the access controller on an unstable case or desk. The access controller might be

damaged severely in case of a fall.

z Ensure proper ventilation of the equipment room and keep the ventilation vents of the access

controller free of obstruction.

z Make sure that the operating voltage is the same one labeled on the access controller.

z Do not open the chassis when the access controller is operating or when electrical hazards are

present to avoid electrical shocks.

z When replacing interface modules, wear the ESD-preventive wrist strap to avoid damaging the

interface modules.

2-2

Installation Site Checking

The WX5004 must be used indoors. You can mount the WX5004 in a cabinet or on a workbench, but

make sure that:

z Adequate clearance is reserved at the air inlet/exhaust vents for heat dissipation.

z The cabinet or workbench is in the environment that has a good ventilation system.

z The cabinet is sturdy enough to support the access controller and its accessories.

z The cabinet or workbench is well earthed.

To ensure normal operation and long service life of your access controller, install it in an environment

that meets the requirements described in the following subsections.

Requirements on Temperature and Humidity

To ensure the normal operation and service lifetime of the access controller, proper temperature and

humidity should be maintained in the equipment room.

z A long term of high humidity may lead to bad insulation, electricity leakage, mechanical property

changes, and metal components corrosion.

z If the relative humidity is too low, captive screws may become loose as a result of contraction of

insulation washers and static electricity may be produced in a dry environment to endanger the

circuits on the access controller.

z A high temperature is the most undesirable condition, because it accelerates the aging of insulation

materials and thus significantly lowers the reliability and service life of the access controller.

The following table lists temperature and humidity requirements for the WX5004.

Table 2-1 Operating environment

Item Description

Operating temperature 0°C to 45°C (32°F to 113°F)

Relative humidity (noncondensing) 5% to 95%

Requirements on Cleanness

Dust is a hazard to the operating safety of the access controller. The dust accumulated on the chassis

can be adsorbed by static electricity and result in poor contact of metal connectors or metal contact

points. Especially, when the relative indoor humidity is low, electrostatic adsorption is more likely to

happen. This can not only shorten the service life of the access controller but also cause

communications failures. The following table lists the dust concentration limit.

Table 2-2 Dust concentration limit in the equipment room

Physical active substance Concentration limit (particles/m

3

)

Dust

≤ 3 × 10

4

(No visible dust on the tabletop over

three days)

Note: The dust particle diameter is ≥ 5 μm

Besides the dust specifications, the equipment room of the access controller also needs to strictly meet

the requirements on the concentration of salt, acid and sulfide. These harmful gases can accelerate the

2-3

metallic corrosion and the aging process of some parts. The specific limits of the harmful gases such as

are given in the following table.

Table 2-3 Limit on harmful gases in the equipment room

Gas Maximum concentration (mg/m

3

)

SO

2

0.2

H

2

S 0.006

NH

3

0.05

Cl

2

0.01

Anti-Static Requirements

Generation and damage of static electricity

In the communication network to which the WX5004 is connected, static induction of the access

controller mainly comes from the following sources:

z External electric fields, such as outdoor high-voltage transmission lines or thunderbolts.

z Internal environment like flooring materials or the structure of the overall system.

Although the WX5004 is designed to be Electrostatic Discharge (ESD) preventive, excessive static

electricity may enormously damage the card circuits or even the whole device.

Protection measures

To prevent electrostatic damage, observe the following:

z Ensure that the access controller and the floor is well grounded.

z Keep the equipment room clean.

z Maintain suitable temperature and humidity;

z Wear ESD-preventive gloves or an ESD-preventive wrist strap and uniform when handling the

circuit board.

z Hold the interface module only by its edge when installing, observing or removing it. Do not touch

the components on it.

z Place the removed interface module on an ESD-preventive workbench with the component-side

facing upward or place it in an antistatic bag.

Wearing ESD-Preventive Wrist Strap

No ESD-preventive wrist strap is shipped with the access controller. You need to purchase one if

needed.

Follow these steps to use an ESD-preventive wrist strap:

1) Put on the ESD-preventive wrist strap.

2) Fasten the ESD-preventive wrist strap and verify that it makes good skin contact.

2-4

3) Lock the terminal of the alligator clip to the ESD-preventive wrist strap.

4) Attach the alligator clip to the rack where the access controller is installed.

5) Make sure that the rack has been well-grounded.

Figure 2-1 Use ESD-preventive wrist strap

（1）

（2）

（3）

(1) ESD-preventive wrist strap (2) Locker (3) Alligator clip

Electromagnetic Environment Requirements

The operation of your access controller may be affected by external interferences, such as capacitance

coupling, inductance coupling, electromagnetic wave radiation, common impedance (including the

grounding system) coupling, and the conducted interference of leads (power cords, signaling cables

and output wires). To eliminate the interferences,

z Use the TN power system as the AC power supply system. A TN power system is called zero

connection protection system. It is a power distribution system with one point connected directly to

earth (ground). The exposed conductive parts and the neutral metal parts of the installation are

connected to that point by protective earth conductors. Use a single-phase three-wire power socket

with a protection earth (PE) to effectively filter interference from the power grid.

z Keep the access controller far from high-power radio transmitters, radars, and high-frequency

heavy-current devices.

z Use electromagnetic shielding measures when necessary. For example, use shielded interface

cables.

z Route interface cables only indoors to prevent signal ports from getting damaged by over-voltage

or over-current caused by lightning strikes.

Laser Safety

The WX5004 is a Class 1 laser device.

2-5

When the optional optical ports on the WX5004 are operating, avoid staring into the optical interfaces

because the high-energy laser beam emitted from the optical fiber may hurt your retina.

Do not stare the laser beam of an optical fiber. Otherwise, your eyes may be hurt.

Installation Tools

z Flat-blade screwdriver

z Phillips screwdriver: P2-150mm

z ESD-preventive wrist strap

No installation tool or ESD-preventive wrist strap is provided with the access controller. You need to

prepare them yourself.

Page is loading ...

H3C WX5004 Installation guide

H3C WX5004 Installation guide

Related papers

Other documents