Speakman S-3661-CA-E Installation guide

Brand: Speakman

Model: S-3661-CA-E

Category: Sanitary ware

Type: Installation guide

Speakman S-3661-CA-E is a single lever deck mounted sink fitting with a polished chrome plated finish. It has a long-life ceramic cartridge, adjustable temperature limit and flow control, and vandal-resistant construction. The 8-inch spread brass gooseneck is swiveling, and the water conserving vandal-resistant flow control reduces flow to 1.5 GPM/5.7 LPM maximum to meet existing ANSI A112.18.1 Standard. The 3/8 compression threaded inlets are for standard hose connections. The Speakman S-3661-CA-E is a great choice for a variety of commercial and residential applications.

SPEAKMAN

400 Anchor Mill Rd. New Castle, DE 19720 Phone: 800-537-2107 Fax: 800-977-2747

7/27/15 Visit us on the web at www.speakman.com 92-S-3661-R6

SPEAKMAN

S-3661, S-3661-CA, S-3661-CA-E Installation, Maintenance &

Operation Instructions

Single Lever Deck Mounted Sink Fitting

DESCRIPTION

Speakman polished chrome plated, NSF compliant, vandal resistant, single lever faucet. Long-life ceramic

cartridge. Adjustable temperature limit and flow control. Brass body constructions, metal handle with color-coded

index. 8” spread brass gooseneck, swivel or rigid. Water conserving vandal-resistant flow control reduces flow to

1.5 GPM/5.7 LPM maximum to meet existing ANSI A112.18.1 Standard. 3/8 compression threaded inlets for

standard hose connections.

SPECIFICATIONS

SUPPLY: 3/8 COMPRESSION (9/16-24 THREAD)

FLOW RATE: 1.5 GPM / 5.7LPM MAX

SHIPPING WEIGHT: 4.6 lbs.

STATIC PRESSURE: 20-80 PSI

INSTALLATION

1) Shut off hot and cold water supplies. Remove old fixture to be replaced and clean mounting surface.

2) Place the rubber o-ring mounting seal on the bottom groove of the valve body. Slip the valve body through

the counter.

3) From underneath the counter, slip the cup washer onto mounting rod and secure with the mounting nut.

Use the spacer for thin sink applications.

Note: The outlet/supply tubes can be bent slightly to allow access to tighten the mounting nut.

Warning: Do not kink the tubes. Kinked tubes will void warranty.

4) Set spout base on the counter and position. From underneath the counter, slip the cup washer onto the

spout base inlet and secure with the mounting nut.

5) Connect water supply lines to inlets of the valve body. Also connect the valve body outlet to the inlet of the

gooseneck with the hose provided. Use 2 wrenches when tightening all body connections.

Warning: When tightening the connections hold the valve body connection while turning the swivel

hose/riser connections.

6) From above sink, install the spout. For All Swiveling Spout: Install spout assembly into the body outlet and

wrench tighten spout collar nut. Do not use the spout locking washer. For Rigid Spout: Place the spout

locking washer into the body outlet, install the spout assembly, position, and wrench tighten the spout

collar nut. For Rigid Vacuum Breaker Spout- VB6/8 (Less “SW” option): Do not use the spout locking

washer. IMPORTANT- First install rigid adapter in body and wrench tighten (See Rough-In on back side of

sheet). Apply thread locker/sealant to the spout tapered pipe threads. Screw the spout into the adapter

until the threads start to get snug. Note- When positioning the spout, hold adapter hex with a wrench, so

body does not move. Holding the hex of the adapter with a wrench, tighten the spout at least 1/3 turn to

the proper position (Do not over tighten spout). Remember that the thread locker/sealant will lock and seal

the spout assembly in place.

7) If applicable, install hose and spray holder to sink/countertop. From above sink, insert inlet end of hose

through holder. Working from under the sink, connect hose inlet to hose and spray outlet of deck body.

Wrench tighten.

8) Turn water supplies on and flush out the fitting. Install outlet device (If applicable) and check all

connections for leaks.

OPERATION

Simply lift the handle up. Rotating the handle will change water temperature.

SPEAKMAN

400 Anchor Mill Rd. New Castle, DE 19720 Phone: 800-537-2107 Fax: 800-977-2747

7/27/15 Visit us on the web at www.speakman.com 92-S-3661-R6

FLOW AND TEMPERATURE ADJUSTMENT INSTRUCTIONS

Adjusting Temperature Limit:

1) Remove handle by removing red/blue button and set screw using an Allen key and remove collar by hand

counter-clockwise.

2) With cartridge control shaft in the center and off position, carefully lift and rotate the temperature limit

stop ring to the desired setting using needle nose pliers or by hand. Clockwise rotation of the ring

increases temperature and counterclockwise rotation of the ring lowers temperature (see table and

schematic for details). Re-install handle and test for desired temperature.

Adjusting Flow Limit control:

1) Using a thin flat screwdriver, carefully remove flow limit stop by prying it away from the cartridge

control shaft.

2) Reset flow limit stop higher on the shaft to increase flow or lower to decrease flow.

3) Re-install handle and check for desired flow.

NOTE: The flow limit adjustment is effective when a higher than 1.5 GPM flow outlet is installed in the faucet or

the flow outlet has been removed.

POSITION

@ 45 PSI.

FLOW

LIMIT

TEMP.

LIMIT

0 0% 0%

1 5% 0%

2 12% 3%

3 25% 10%

4 20%

5 30%

6 40%

SPEAKMAN

400 Anchor Mill Rd. New Castle, DE 19720 Phone: 800-537-2107 Fax: 800-977-2747

7/27/15 Visit us on the web at www.speakman.com 92-S-3661-R6

MAINTENANCE (CARE and CLEANING)

Valves are washerless and require no routine maintenance. The gleaming finish of your SPEAKMAN single lever

faucet can be cleaned by using mild soap and warm water. Dry immediately with a soft, clean cloth for best

results.

ROUGH-IN

REPAIR/REPLACEMENT PARTS

ITEM NUMBER PART NUMBER DESCRIPTION

G18-0217-PC

8" SPREAD GOOSENECK ASSEMBLY

2 RPG05-0837-PC 1.5 GPM AERATOR ASSEMBLY

3 RPG05-0851-PC 1.5GPM LAMINAR FLOW OUTLET ASSEMBLY

4 G20-1979-PC SINGLE LEVER FAUCET

63-0042 HOSE CONNECTION

RPG05-40005 1.2GPM AERATOR ASSEMBLY

RPG05-40015 1.2GPM LAMINAR FLOW OUTLET ASSEMLBY

Speakman S-3661-CA-E Installation guide

Brand: Speakman

Model: S-3661-CA-E

Category: Sanitary ware

Type: Installation guide

Download PDF

report

Speakman S-3661-CA-E Installation guide

Speakman S-3661-CA-E Installation guide

Related papers

Other documents