Ø1"(25)
4"
(100mm)
Pre drilled hole size :
1.26" to 1.5"(32mm to 38mm)
Hole Size
Unsuitable sink size：
1"(25mm)
Hole Size
1.26" to 1.5"
(32mm to 38mm)
Hole Size
4"-16"
(100-400mm)
OPERATION
• Double levers style handles
• Maximum handle(s) rotation angle is 90˚ to full on
• Rotate hot side counter clockwise to open (clockwise to close)
• Rotate cold side clockwise to open (counter clockwise to close)
TWO HANDLE LAVATORY
CENTERSET FAUCETS
You may need
With 1.2 gpm are compliant with
California water effi ciency regulations,
Complies with California Proposition
65 and with the Federal Safe Drinking Water Act.
In areas with extremely low water pressure causing
the basin faucet water flow to be unsatisfactory ,
replace the 2.2 gpm aerator to improve the water flow in the basin faucet.
Cleaning and Care
Care should be given to the cleaning of this product. Although its finish is
extremely durable,
It can be damaged by harsh abrasives or polish. To clean, simply wipe gently
with a damp cloth and blot dry with a soft towel.
To READ ALL the instructions completely before beginning.
For easy installation of your faucet you will need:
To READ ALL warnings, care, and maintenance information.
Cold
Hot
Close
Open
Close
Open
washer
1.2gpm aeratot
aeratot house
1.2GPM 4.5L/min
3x1.1" to 1.5"
(28mm to 38mm)
Hole Size
1.2"(30mm)
Max. deck
Thickness
3x 1.8"
(45 mm)
2.5"
(63mm)
Hot Cold
4" to 16"
(100mm to 406mm)
9.5" to 21.5"
(240mm to 546mm)
Hot
24"(600mm)
M10x1mm
(120mm)
4.7"
(186mm)
7.3"
(105mm)
4.1"
9/16“ :"(\"
M14mm
Ø26mm Ø26mm
1 1/4''
(Ø32mm)
9.5"(240mm)
8.7"(220mm)
Ø2.2"
(56mm)
Min. 1.6"
(Ø41mm)
Hole Dia
1.1" to
2.5"
(28 to
64mm)
Align tabs and tabs on quick
connects .
Push quick connects firmly upward
and snap onto receiving tube tab .
Pull down moderately to ensure each
connection has been made.
1.Remove the washer (2) , black
gasket (4) and nut (5) from the
assembly.
2.Slide washer (2) up to underside
of flange (3).
Insert flange (3) and washer (2) into
sink and secure with the black
gasket (4) washer and nut (5) from
underneath the sink.
3.Put down and check the
Springloaded stopper (1).
4. Connect assembly to drain.
1
2
3
4
5
To flush debris from the plumbing
system:
1.Remove the aerator by hand.
2.Run hot and cold water for
one minute.
3.Replace the aerator.
Repeat for other hose connection
making sure the hose with the hot
label is connected to the hot supply
valve and the other
hose is connected to the cold supply
valve.
FLUSH SYSTEM/CHECK FOR LEAKS.
Turn on hot and cold water supplies
and flush water lines for one minute.
Check all connections at arrows for
leaks.
Retighten if necessary, but do not
overtighten.
NOT WITH apply teflon tape to
the quick connect installation.
5
67
Before installing the valves, clean the
water pipe thoroughly to avoid dirt
and deposits.
1
Attach flexible hoses under the
hot and cold end valves.
C
1
1
2
3
Install spout (1) O-ring (2) , Secure
with washer and nut (3).
Note: If sink is uneven, use silicone
under the gasket.
1
3
2
5
4
6
7
H
C
1.Make sure attach the gasket to the
base of hot (1) and cold (2) end valves.
2.Slide hot (1) and cold (2) end valves
with flexible hoses (3) through sink.
3.Place washer(4) and metal plate(5)
over mountingstud under sink. Secure
with mounting nut(6).
4.Lock mounting nut(6) into position by
tightening
screw (7).
H
Notes
2
3 4
1.
7
2.
3.
/
