Leviton R08-IPS02-1LT Installation guide

Brand: Leviton

Model: R08-IPS02-1LT

Type: Installation guide

WARNINGS AND CAUTIONS:

• Ifyouarenotsureaboutanypartoftheseinstructions,consultanelectrician.

• Cleanoutersurfacegentlywithdampclothonly.DO NOT usesoapsorcleaningliquids.

• Nouserserviceablecomponents.DO NOT attempttoserviceorrepair.

• UsethisdeviceWITH COPPER OR COPPER CLAD WIRE ONLY.

WARNINGS AND CAUTIONS:

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE

POWER IS OFF BEFORE WIRING!

• Tobeinstalledand/orusedinaccordancewithelectricalcodesandregulations.

• Toavoidoverheatingandpossibledamagetothisdeviceandotherequipment,DO NOTinstalltocontrolareceptacle.

• DO NOT controlaloadinexcessofspeciedratingsoryoumaydamageproperty,orcauseinjuryordeath.

RESET

TEST

1 2

0 3

Push down tabs per

diagram, one at a time and

rotate forward to release

1 2

0 3

1 2

0 3

Attach new face by inserting

bottom hinge tabs, then pivot

and snap the color kit to attach

Tools needed to install your Device

Changing the color of your device

Slotted/PhillipsScrewdriver ElectricalTape Pliers

Pencil   Cutters  Ruler

√

INSTALLING YOUR DEVICE

NOTE: UsecheckboxeswhenStepsarecompleted.

ONOFF

ONOFFONOFF

ONOFF

Step 1

WARNING:TO AVOID FIRE, SHOCK, OR DEATH;

TURN OFF POWERatcircuitbreakerorfuseandtest

thatpowerisoffbeforewiring!

Single-Pole

1. Line(Hot)

2. Neutral

3. Ground

4. Load

Step 2

Identifying your wiring application

(most common):

NOTE:Ifthewiringinthewallbox

doesnotresembleanyofthese

congurations,consultanelectrician.

WIRING SENSOR:

Connect wires per WIRING DIAGRAM as follows:

NOTE: Agroundconnectionisrequiredtooperate.Usethegroundwire

intheelectricalboxforgroundconnection.Ifthereisnogroundwire,

makesuretheelectricalboxisgroundedandattachthegroundwireto

theboxwithascrew.

• GreenorbarecopperwireinwallboxtoGreenterminalscrew.

• LineHotwallboxwiretoterminalscrewmarked"BK".

• Loadwallboxwiretoterminalscrewmarked"RD".

• ProceedtoStep5.

Hot (Black)

Neutral (White)

Red

Black

White

LOAD

Line

120VAC, 60 Hz

Sensor

Green

Ground

Terminal

Screw marked

Red (RD)

Terminal

Screw marked

Black (BK)

Single Pole Wiring Application:

Step 4

Single Pole Wide View Motion Activated Light Control

Cat. No. IPS02, IPV02 - INDOOR USE ONLY

Ratings:120VAC,60Hz-300WIncandescent-150WLED,CFL-200VAELV,MLV-Fluorescent2.5A-Resistive-1/6thHP

INSTALLATION INSTRUCTIONS

PK-93020-10-00-2A

FEATURES

• Cat.No.IPS02andIPV02haveasensingareaofcoverageof30ft.x

30ft.,andasensingangleof180

(seeSensingAreaCoveragegure

onpage2)

• Adjustablelightandtime-delaycontrolsarelocatedonthefrontofthe

device.Seeadjustmentsettingsectiononpage2fordetails.

• LEDindicatorisusedtoalerttheuserofthestatusofthedevice.

• AdjustableTimeDelaysettingfor30seconds,5minutes,

15minutesand30minutes.

• Occupancysensorscanbeconvertedtovacancysensors.

See Adjustment Section page 2.

LOCATION / MOUNTING

Thedevicerespondstotemperaturechangesandcareshouldbetaken

whenmountingthedevice.DO NOTmountdirectlyaboveaheatsource,

inalocationwherehotorcolddraftswillblowdirectlyonthesensor,or

whereunintendedmotion(e.g.,hallwaytrafc)willbewithinsensor’s

eld-of-view.

Preparing and connecting wires:

Thisdevicecanbewiredusingsidewireterminalscrews.

Chooseappropriatewirestrippingspecicationsaccordingly.

Strip Gage

(measure bare wire

here or use gage on

back of the sensor)

5/8”

(1.6 cm)

Cut

(if necessary)

Side Wire Connection

Sidewireterminalsaccept#14-12

AWGsolid copper wire only.

Step 3

Back Wire

Backwireopeningsuse#14-12

AWGsolid copper wire only.

YL 3-Way

Yourdevicemayincludecoloroptions.Tochangecoloroftheface

proceedasfollows:

• Makesurethattheendsofthewiresfromthewallboxarestraight

(cut if necessary).

• Removeinsulationfromeachwireinthewallboxasshown.



LIMITED5YEARWARRANTYANDEXCLUSIONS

Levitonwarrantstothe originalconsumerpurchaserand notforthe benetof anyone

else that this product at the time of its sale by Levitonis free of defectsin materials

and workmanship under normaland proper use forfive years from the purchase

date. Leviton’s only obligation is to correct such defects byrepairor replacement, at

itsoption, ifwithin suchveyearperiod theproduct isreturnedprepaid, withproof of

purchasedate, anda descriptionoftheproblemtoLeviton Manufacturing Co., Inc.,

Att: Quality Assurance Department, 201 North Service Road, Melville, New York

11747.Thiswarrantyexcludesandthere isdisclaimed liabilityforlaborforremovalof

thisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperly

orinanimproperenvironment,overloaded,misused,opened,abused,oralteredinany

manner,orisnotusedundernormaloperatingconditionsornotinaccordancewithany

labelsorinstructions.There are no other or implied warranties of any kind, including

merchantability and ﬁtness for a particular purpose,but ifany impliedwarranty is

requiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,including

merchantabilityandtnessforaparticularpurpose,islimitedtoveyears.Leviton is not

liable for incidental, indirect, special, or consequential damages, including without

limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or delay

or failure to perform this warranty obligation.Theremediesprovidedhereinarethe

exclusive remedies under this warranty, whether basedoncontract,tort or otherwise.

PK-93020-10-00-2A©2012LevitonMfg.Co.,Inc.

• Positionallwirestoprovideroomin

outletwallboxfordevice.

• Ensurethattheword"TOP"is

facingupondevicestrap.

• Partiallyscrewinmountingscrews

inwallboxmountingholes.

• Restorepoweratcircuitbreakerorfuse.

• Wait40secondsforsensortopowerup.

• ForIPS02,lightswillautomaticallyturnON

afterpowerisapplied.

• ForIPV02,presspushpad.Lightsshould

turnON.

 If lights still do not turn ON, refer to the

TROUBLESHOOTING section.

Step5

Restore Power:Restorepoweratcircuitbreakeror

fuse.Installation is complete.

Step 7

Device Mounting: TURN OFF POWER AT CIRCUIT

BREAKER OR FUSE.

Step 6

Installationmaynowbe

completedbytightening

mountingscrewsintowall

box.Attachwallplate.

OPERATION

NOTE: Dresswireswithabendas

shownindiagraminordertorelieve

stresswhenmountingdevice.

For additional information, contact Leviton’s Techline at

1-800-824-3005orvisitLeviton’swebsiteatwww.leviton.com

ThisproductiscoveredbyU.S.Pat.No.7,924,155&correspondingforeignpatents.

©2012LevitonManufacturingCo.,Inc.AllRightsIncludingTradeDressRightsReserved

DECORAisatrademarkofLevitonManufacturingCo.,Inc.registeredintheUnited

States,Canada,MexicoandChina.

ADJUSTMENT SETTINGS

TROUBLESHOOTING

Lights do not operate with push pad and LED indicator does not

blink when motion is present:

• Ensurepropergroundconnectionispresentinthewallbox.

Whenconrmed,verifywiringconnectionstosensor.

Lights do not switch ON when motion is detected (IPS02):

• Motionisbeyondsensingrange,moveclosertoswitch.

• Adjustthelightleveladjustmenttowardlighter(counterclockwise),

dependingonroomconditions.

Lights always stay ON:

• ChecktimedelaysettingsandcomparetohowlongthelightsstayON.

• Ensurethatnomotionoccursincoverageareafortimeselected.

• Checkthatswitchisnotinstallednearaheatsource(e.g.,stove,lights,

heatvents)ordetectingmotionfromanadjacentarea(e.g.,hallway

trafc).Ifso,switchmayhavetoberelocated.

Lights do not turn ON - IPV02:

• Checkthatcontrolisinstalledcorrectly.

• CheckthatpowerisON.

• Checkthatlightbulbisfunctioning.

NOTE:Ifproblemscontinue,consultanelectrician.

IPS02

Auto On: LightswillautomaticallyturnONwhen

roomisoccupiedormotionisdetected.

TheIPS02willswitchlightsOFFwhenno

motionisdetectedinun-occupiedroomafterset

periodoftime.

Time delay adjustment:Refertosectionon

Adjustmentsettings.

TheIPS02willmanuallyturn-onlightsorthe

loadbydepressingtheON/OFFpaddleonthe

device.TheIPS02canbesettoonlyturnONby

thepushpad(noautomaticONoperation)byadjustingtheambientlight

controltothe"0"position.

IPV02

Manual On:TheIPV02requirestheusertomanuallyturn-onlightsorthe

loadbydepressingtheON/OFFpaddleonthedevice.

Thelightsorloadwillautomaticallyturn-offwhentheroomisleft

un-occupiedforasetperiodoftime.

Time delay adjustment:RefertosectiononAdjustmentsettings.

Locator Light LED:

LEDblinksonceevery2secondswhenmotionisdetectedandiftheload

isONorOFF.

FCC COMPLIANCE STATEMENT

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttofollowing

twoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevice

mustacceptanyinterferencereceived,includinginterferencethatmaycauseundesired

operationofthedevice.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBDigital

Device,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovide

reasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.This

equipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalled

andusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradio

communications.However,thereisnoguaranteethatinterferencewillnotoccurina

particularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioor

televisionreception,whichcanbedeterminedbyturningtheequipmentOFFandON,

theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowing

measures:

•ReorientorrelocatethereceivingAntenna.

•Increasetheseparationbetweentheequipmentandthereceiver.

•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthe

receiverisconnected.

•Consultthedealeroranexperiencedradio/tvtechnicianforhelp.

FCC CAUTION

AnychangesormodicationsnotexpresslyapprovedbyLevitonManufacturingCo.,Inc.,

couldvoidtheuser'sauthoritytooperatetheequipment.

SENSING AREA COVERAGE

Field-of-View (Horizontal)

Side (Vertical) Field-of-View

Testing your Device prior to mounting in

wall box:

1. Withpowerrestoredandwallplateremoved,removefaceofdeviceto

exposesettingcontrols,seecolorchangeinstructionsinpage1.Use

yourngerorasmallscrewdrivertoadjustthelightsensitivityandtime

settingsonthedeviceasfollows:

Light Level Adjustment:

• Turnthecontrolclockwise.LightswillturnONinlighterconditions.

• Turnthecontrolcounterclockwise.LightswillturnONinlesslighting

conditions.

Time Selection:

• Adjustthetimeselectortothedesiredlengthoftimethelightsareto

remainON.LightswillremainONfrom30secondsto30minutesafter

theroomisvacated.

• Turnthecontrolclockwise.LightswillremainONupto30minutes.

• Turnthecontrolcounterclockwise.LightswillremainONupto30

seconds.

2. Testthatthelightlevelandtimeselectionareasdesired.Ifnot,repeat

adjustmentsuntilsatised.

3. Mountwallplate.INSTALLATION IS COMPLETE.

Lens

Push

Pad

Locator

Light

1.5m

5ft

30ft

9.1m

30ft

9.1m

6ft

1.7m

1.8m

6ft

5ft

1.5m

30ft

9.1m

1.4m

4ft

8.4m

27ft

2.1m

7ft

1.5m

5ft

1.2m

4ft

1.7m

6ft

2.6m

8ft

Light Level

Adjustment

Time

Selection

1 2

0 3

1 2

0 3

Settings

30Sec

5Min

15Min

30Min

Time

NOTE:TooperatetheIPS02asavacancysensor(ManualON/AutoOFF):

rotatethelightlevelsensitivityfullycounterclockwise.

FOR CANADA ONLY

Forwarrantyinformationand/orproductreturns,residentsofCanadashouldcontact

LevitoninwritingatLeviton Manufacturing of Canada Ltd to the attention of

theQualityAssuranceDepartment,165HymusBlvd,Pointe-Claire(Quebec),

Canada H9R 1E9orbytelephoneat1800405-5320.

Leviton R08-IPS02-1LT Installation guide

Leviton R08-IPS02-1LT Installation guide

Leviton R08-IPS02-1LT Installation guide

Related papers

Other documents