Instruction manual
ID: #05007
m
y
h
a
n
s
e
c
o
n
t
r
o
l
.
c
o
m
M
A
N
U
A
L
D
E
V
E
L
O
P
E
D
I
N
G
E
R
M
A
N
Y
User-friendly
Manual
Made in China
Distributed by:
ALDI STORES,
1 SARGENTS ROAD
MINCHINBURY NSW 2770
www.aldi.com.au
YEARS
WARRANTY
General information
Reading and storing the instruction manual
This instruction manual is part of this car socket adaptor. It contains important
information on how to use the car socket adaptor.
For improved readability
, the car socket adaptor
will be referred to only as the “
adaptor
” below.
Before using the adaptor, read the instruction manual carefully. This particularly applies for
the safety notes. Failure to heed this instruction manual may result in severe injury or dam-
age to the adaptor.
The instruction manual is based on the standards and rules in force in the European Union.
When abroad, you must also observe country-specific guidelines and laws!
Store the instruction manual for future use. If you pass the adaptor on to third parties, please
be absolutely sure to include this instruction manual.
Explanation of symbols
The following symbols and signal words are used in this instruction manual, on the adaptor
or on the packaging.
WARNING! This signal word designates a hazard with a moderate degree
of risk which may lead to death or severe injury if not avoided.
CAUTION! This signal word designates a hazard with low risk that, if not
avoided, may result in minor or moderate injury.
NOTICE! This signal word warns against possible damage to property
or provides you with useful additional information on operating the
product.
Safety
Proper use
The adaptor is exclusively designed for use in motor vehicles for charging electronic devices
with a low level of power consumption, e.g. navigation systems or mobile phones. The
adaptor is not intended for heating up cigarette lighters.
Only use the adaptor as described in this instruction manual. Any other use will be deemed
as not in accordance with the instructions and may lead to damage of property or injury to
persons.
The manufacturer or vendor accepts no liability for damage caused by improper or incorrect
use.
AFTER SALES SUPPORT
1800898570
Model: CSA06
Product code: 92201/2015 07/2015
AUS
Safety notes
WARNING!
Risk of accident!
Improperly tampering with the adaptor, mounting
it improperly or loose cables may cause impair-
ment when driving motor vehicles. The adaptor
could become a dangerous projectile. The driver
could get caught in the cable. This could result in
accidents.
− Never tamper with the adaptor while driving.
− Secure the adaptor with the double-sided adhesive tape in-
cluded in the product contents or similar mounting materials.
− Regularly check to make sure that the adaptor is secure.
− Tie the excessive length cable together. Never let the cable
hang freely out of driver's reach.
WARNING!
Danger of suffocation!
If children swallow the packaging or small parts or
catch themselves, they could choke.
− Keep packaging parts and small parts away from children.
− Do not allow children to play with the adaptor.
CAUTION!
Risk of short circuit!
Improper handling of the adaptor may result in a
short-circuit. This may cause a fire.
− Only use the adaptor with a proper, undamaged fuse of the
same fuse type (see section “Technical data”).
− Replace the fuse after a short-circuit (see section “Inserting/
changing the fuse”).
− Never insert metallic objects such as keys, coins or paper clips
in the opening of the adaptor sockets or in the USB ports.
NOTICE!
Using the adaptor when the motor is not running
could drain the vehicle battery. You may not be
able to start the vehicle as a result.
− Only charge devices while the motor is running.
NOTICE!
Handling the adaptor improperly could damage it.
− Never use the adaptor to heat up a cigarette lighter.
B
8
9
10
Product contents⁄device
parts
1
Adaptor sockets (3 pieces)
2
Control light
3
USB port (2 pieces)
4
Power plug
5
Adhesive strip
6
Cable
7
Cable strap
8
Contact tip
9
Fuse
10
Cap
A
5V
1A
12V 24V
12V 24V
12V
5V
2.1A
24V
1
6
3
4
5
2
7
Doc./Rev. No. 92868_20150217_AUS
Car Socket
Adaptor
AUS
− The adaptor also consumes a small amount of electricity when
in standby. Disconnect the adaptor from the on-board electri-
cal system after use.
− Remove the adaptor from the on-board electrical system by
gently pulling on the power plug. Never pull on the cable.
− In the event of damage, have a qualified professional repair
the adaptor. Never open the adaptor yourself.
Assembly
1. Remove the packaging material and check the product contents (see fig. A and B).
2. Clean the areas in the vehicle where you would like to mount the adaptor. Make sure
that these areas are free from grease and dust-free.
3. Also clean the area on the adaptor where you would like to mount the adaptor (see
section “Cleaning and maintenance”).
4. On one side, remove the protective paper from the adhesive strip
5
and stick the ad-
hesive strip to the desired area in your vehicle.
5. Remove the second protective paper from the adhesive strip and stick the adaptor onto
the adhesive strip. Push the adaptor firmly onto the adhesive strip.
You have successfully mounted the adaptor.
Handling
Connecting the adaptor
1. Connect the adaptor to the vehicle's on-board electrical system by inserting the power
plug
4
all the way into the board socket of the vehicle.
2. Bundle the cable
6
and pull the cable strap
7
over the resulting loops. Use the
cable strap to secure the cable.
3. The control light
2
will illuminate in red.
You have successfully connected the adaptor.
Connecting devices
NOTICE!
The output voltage of the adaptor sockets de-
pends on the vehicle configuration.
− If the vehicle is equipped with a board voltage
of 12V, the adaptor socket will supply 12V.
− If the vehicle is equipped with a board voltage
of 24V, the adaptor socket will supply 24V.
− Insert the power plug of the device you intend to connect all the way into one of the
adaptor sockets
1
.
− Insert the USB connector of the device you intend to connect into one of the USB ports
3
.
Cleaning and maintenance
Cleaning the adaptor
NOTICE!
Risk of short circuit!
Water that has penetrated the housing may cause
a short circuit.
− Never immerse the adaptor in water.
− Make sure that no water penetrates the
housing.
NOTICE!
Risk of damage!
If you clean the adaptor improperly, you could
damage it.
− Do not use any aggressive cleaners, brushes
with metal or nylon bristles, sharp or metallic
cleaning utensils such as knives and the like.
They could damage the surfaces.
1. Pull the power plug
4
out of the board socket before cleaning.
2. Clean the adaptor with a damp cloth.
3. Then let the adaptor dry completely.
Inserting⁄changing the fuse
1. Pull the power plug
4
out of the board socket.
2. Screw the cap
10
off of the power plug by turning it counter-clockwise.
3. Remove the fuse
9
and insert a new, undamaged fuse of the same type (see section
“Technical data”).
4. Screw the cap onto the power plug. In the process, make sure that the fuse enters into
the contact tip
8
.
Storage
NOTICE!
Risk of damage!
If the vehicle is parked in the sun for prolonged
periods, extreme temperatures may arise inside
the vehicle and glove compartment.
− Never expose the adaptor to extreme stresses
such as heat, cold, moisture and direct sunlight.
1. Remove the adaptor from the on-board electrical system.
2. Store the adaptor in a clean, dry area.
Make sure the temperatures in the storage location are within a moderate range.
We recommend that you use the original packaging to store it.
Technical data
Type: CSA06
Article number: 92201/2015
Input voltage: 12V / 24V DC (depending on the on-board electrical
system)
Total output: max. 120W at 24V DC or
max. 60W at 12V DC (depending on the on-board
electrical system)
Dimensions (W x H x D): approx. 3.2 x 11.5 x 4.9 cm
Cable length: approximately 120cm including plug
Plug diameter: approx. 20mm
Operating temperature: -30°C to +25°C
Fuse: F, 8A, L, 150V, 5 x 20mm
Adaptor socket (3 pieces)
Output voltage: 12V / 24V DC (depending on the on-board electrical
system)
Current rating: max. 5A
Inner diameter: approx. 21mm
USB port (2 pieces)
Output voltage: 5V DC each
Current rating: total of 3.1A (1 x 2.1A and 1 x 1A)
Disposal
Disposing of the packaging
− Dispose of the packaging separated into single type materials. Dispose of cardboard and
carton as waste paper and foils via the recyclable material collection service.
Disposing of old devices
− Dispose of
the adaptor
in accordance with the applicable laws and regulations for your
country
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
NextBase 212 Owner's manual
-
-
-
NextBase 212G Owner's manual
-
Sony DRN-XM01C2 User manual
-
NextBase Duo User manual
-
Motorola DCS StarTac User manual
-
Delphi SA10035 - Roady XM Satellite Radio Receiver User manual
-
NextBase 245601 User manual
-
