The SUSSEX VFMT is a floormount mixer with a 5.0-liter water rating, which ensures water efficiency. It comes with various fixing distances, allowing you to choose the best fit for your bathroom setup. The mixer features a durable construction and can be used with both concrete and wooden floors. Installation requires rough-in and fit-off processes. Detailed instructions for both types of flooring are provided in the manual. Once installed, the mixer offers precise water control and adds a touch of sophistication to your bathroom.
The SUSSEX VFMT is a floormount mixer with a 5.0-liter water rating, which ensures water efficiency. It comes with various fixing distances, allowing you to choose the best fit for your bathroom setup. The mixer features a durable construction and can be used with both concrete and wooden floors. Installation requires rough-in and fit-off processes. Detailed instructions for both types of flooring are provided in the manual. Once installed, the mixer offers precise water control and adds a touch of sophistication to your bathroom.
2
SUSSEX
INFO & INSTALL GUIDES
CONCEPTS
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
INFORMATION SHEET
Calibre Basin Mixer
Product code: CBM
160
80
100
40
35
48
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
Calibre Basin Mixer
Product code: Available options:
CBM Basin Mixer
CEBM Extended Basin Mixer
INSTALLATION GUIDE
PLUMBER NOTE
-On-site testing using higher water pressures must be
conducted with the Mixer in the closed position.
(STATIC TEST )
-Under no circumstances is the Mixer to be opened
when exceeding the maximum stated water pressure.
-At the completion of testing, do not relieve any high
water pressure by operating the Mixer.
-Exposing the internals of the Mixer Cartridge to higher
than specified water pressures will void the
manufacturers warranty.
INSTALLATION GUIDELINES
-The Mixer is supplied assembled, only the Fixing nut
and the Clamp need to be removed.
-After removing the mentioned parts, lower the Mixer
on to the mounting surface and fit the Flexible Hoses.
-In some cases the Flexible Hoses may need to be fed
through from under the mounting surface and then
attached. (Tighten using appropriate spanner)
-After securing the Flexible Hoses, fit Clamp and attach
the Fixing Nut from underneath.
-Before fully securing the Mixer ensure that the Base O
Ring is intact and the Mixer is properly centered over
the mounting surface hole.
-The Mixer mounting surface must be completely sealed
and water-tight.
-The 1/2” Fittings of the Flexible Hoses have a conical
seal, ensure that the matching threads are cut square
and burr free.
-Prior to connecting the Flexible Hoses, ensure all
pipework is thoroughly flushed and ensure pipework is
free of any dirt or debri.
-Isolating Stop Valves are recommended with all
installations. (not supplied)
-Connect the Flexible Hoses to Hot and Cold pipework
fittings, ensure the Hoses do not kink or become
twisted when tightening.
-Check all fittings and connections are secure and
water-tight.
BASE
O-RING
CLAMP
Hole Size
32-35mm
50mm Max.
Bench thickness
1/2" BSP Fittings
with conical Seals FLEXIBLE HOSES
FIXING
NUT
CONCEPT One
Product code
Voda
VFMT Floormount mixer 160mm
VFM200T Floormount mixer 200mm
VFM250T Floormount mixer 250mm
VFMHT Floormount mixer with hand held
VFMMCT Floormount mixer with curved outlet
VFMBMCT Floormount basin mixer curved
Floormount mixer Fixing distances
sussextaps.com.au
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
2
SUSSEX
INFO & INSTALL GUIDES
CONCEPTS
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
INFORMATION SHEET
Calibre Basin Mixer
Product code: CBM
160
80
100
40
35
48
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
Calibre Basin Mixer
Product code: Available options:
CBM Basin Mixer
CEBM Extended Basin Mixer
INSTALLATION GUIDE
PLUMBER NOTE
-On-site testing using higher water pressures must be
conducted with the Mixer in the closed position.
(STATIC TEST )
-Under no circumstances is the Mixer to be opened
when exceeding the maximum stated water pressure.
-At the completion of testing, do not relieve any high
water pressure by operating the Mixer.
-Exposing the internals of the Mixer Cartridge to higher
than specified water pressures will void the
manufacturers warranty.
INSTALLATION GUIDELINES
-The Mixer is supplied assembled, only the Fixing nut
and the Clamp need to be removed.
-After removing the mentioned parts, lower the Mixer
on to the mounting surface and fit the Flexible Hoses.
-In some cases the Flexible Hoses may need to be fed
through from under the mounting surface and then
attached. (Tighten using appropriate spanner)
-After securing the Flexible Hoses, fit Clamp and attach
the Fixing Nut from underneath.
-Before fully securing the Mixer ensure that the Base O
Ring is intact and the Mixer is properly centered over
the mounting surface hole.
-The Mixer mounting surface must be completely sealed
and water-tight.
-The 1/2” Fittings of the Flexible Hoses have a conical
seal, ensure that the matching threads are cut square
and burr free.
-Prior to connecting the Flexible Hoses, ensure all
pipework is thoroughly flushed and ensure pipework is
free of any dirt or debri.
-Isolating Stop Valves are recommended with all
installations. (not supplied)
-Connect the Flexible Hoses to Hot and Cold pipework
fittings, ensure the Hoses do not kink or become
twisted when tightening.
-Check all fittings and connections are secure and
water-tight.
BASE
O-RING
CLAMP
Hole Size
32-35mm
50mm Max.
Bench thickness
1/2" BSP Fittings
with conical Seals FLEXIBLE HOSES
FIXING
NUT
CONCEPT One
HO T/ CO LD
FE ED CH A NN EL
HO T/ CO LD
FE ED CH ANNEL
Ap p rox.
400m m
Ap pro x.
400m m
CONCRETE RECES REQUIREMENTS
FIXED AND CONNECTED VALVE BACK FILLED RECESS
FIXINF AND CONNECTIONS
(FIXING VALVE)
Voda
Fixing and connections (Fig. 2 & 3)
Back-filled recess (Fig. 4)
Existing concrete floor
New concrete floor (pre-pour)
*To install the Floormount Fixing Valve a 50mm step down (recess) is required in the concrete surface where
the floormount is to be located.
- The recess area is to be a minimum of 200 x 300mm to allow enough room for the fixing valve to be fitted.
NOTE: This can be a larger area if unsure of exact mounting position.
Important: the recess area is required to be 50mm deep and must be flat and level.
- Connect 1/2” elbows (or male/female nipples) to Fixing Valve in preparation for the hot/cold water lines.
- Postion fixing valve into concreted recess area.
NOTE: Align “Front” to face bath or wash vessel.
- Mark and drill for 8mm “dyna bolt” or other appropriate anchoring bolts (not supplied).
- Fix Floormount Fixing Valve and complete hot and cold water line connections.
- Ensure the valve is level and well anchored.
- Tighten “end caps” and perform water testing, and ensure there are no water leaks.
- Leave end caps, pressure plate and fixing bolts in the valve to protect the threads until final fit-off.
- Once all water connections are made and tested, fill in the recessed area and channelling up to the
Fixing Valve with a mortar mix.
- After mortar has set, seal the area between mortar and the Fixing Valve.
- Cut 400 x 400mm section through concrete slab where the floormount mixer is to be located (Fig. 1).
- Remove cut section and drill for the appropriate concrete ‘tie-rods’ into side walls of cavity.
- Fit ‘tie-rods’ and pour concrete to create a 50mm step down (recess) from the original concrete
floor surface (Fig. 1).
NOTE: Recess area must be flat and level.
- Hot and cold lines can be chased into the recessed area by cutting a minimum 50 x 50mm channel (Fig. 1).
*To install this floormount fixing valve, a 50mm step down (recess) is required in the concrete slab. The floormount fixing
valve is supplied with end caps, pressure plate and fixing bolts. Leave intact until final fit off with the floormount mixer.
Floormount mixer Concrete floor Rough-in
sussextaps.com.au
2
SUSSEX
INFO & INSTALL GUIDES
CONCEPTS
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
INFORMATION SHEET
Calibre Basin Mixer
Product code: CBM
160
80
100
40
35
48
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
Calibre Basin Mixer
Product code: Available options:
CBM Basin Mixer
CEBM Extended Basin Mixer
INSTALLATION GUIDE
PLUMBER NOTE
-On-site testing using higher water pressures must be
conducted with the Mixer in the closed position.
(STATIC TEST )
-Under no circumstances is the Mixer to be opened
when exceeding the maximum stated water pressure.
-At the completion of testing, do not relieve any high
water pressure by operating the Mixer.
-Exposing the internals of the Mixer Cartridge to higher
than specified water pressures will void the
manufacturers warranty.
INSTALLATION GUIDELINES
-The Mixer is supplied assembled, only the Fixing nut
and the Clamp need to be removed.
-After removing the mentioned parts, lower the Mixer
on to the mounting surface and fit the Flexible Hoses.
-In some cases the Flexible Hoses may need to be fed
through from under the mounting surface and then
attached. (Tighten using appropriate spanner)
-After securing the Flexible Hoses, fit Clamp and attach
the Fixing Nut from underneath.
-Before fully securing the Mixer ensure that the Base O
Ring is intact and the Mixer is properly centered over
the mounting surface hole.
-The Mixer mounting surface must be completely sealed
and water-tight.
-The 1/2” Fittings of the Flexible Hoses have a conical
seal, ensure that the matching threads are cut square
and burr free.
-Prior to connecting the Flexible Hoses, ensure all
pipework is thoroughly flushed and ensure pipework is
free of any dirt or debri.
-Isolating Stop Valves are recommended with all
installations. (not supplied)
-Connect the Flexible Hoses to Hot and Cold pipework
fittings, ensure the Hoses do not kink or become
twisted when tightening.
-Check all fittings and connections are secure and
water-tight.
BASE
O-RING
CLAMP
Hole Size
32-35mm
50mm Max.
Bench thickness
1/2" BSP Fittings
with conical Seals FLEXIBLE HOSES
FIXING
NUT
CONCEPT One
100mm MIN
50mm TYP
400mm
50mm
NOGGIN
JOIST
JOIST
40mm
APPROX
TILE
GLUE
WATER
PROOF
19mm
PARTICLE
BOARD
END
CAPS
M8
BOLT
NOGGIN
JOIST
JOIST
HOT
COLD
50mm
SCREW AND WASHER
(X 4) (NOT SUPPLIED)
END CAP (WITH SEAL)
FLOORMOUNT MIXER
ADAPTER PLATE
CONNECTING FITTING
FLOORMOUNT MIXER
VALVE BODYE LBOW (X2)
(NOT SUPPLIED)
COLDHOT
FRONT
FLOORMOUNT
MIXER VALVE
BASE PLATE
PRESSURE PLATE
NOGGINJOIST JOIST
M8 X4 0 BO LT
CONCRETE RECES REQUIREMENTS
FIXED AND CONNECTED VALVE BACK FILLED RECESS
FIXINF AND CONNECTIONS (WOODEN)
(FIXING VALVE)
Voda
Floormount mixer Wooden floor Rough-in
Fixing and connections (Fig. 2 & 3)
Back-filled recess (Fig. 4)
Rough-in (Wooden floor)
- Fix a 100x50mm min noggin. 50mm below the top of the joists in the position where the floormount mixer is to
be located (Fig. 1).
NOTE: the floormount mixer has been supplied to suit a concrete installation. Some parts need to be changed to
suit a wooden floor.
- To suit wooden flooring, remove the m8x25mm bolts and the pressure plate. Using a 6mm allen key, remove the
two connection fittings (O-ring sealed) and replace with the longer version (tighten well).
- Add the Floormount Mixer Adapted Plate. Replace the Pressure Plate and loosely fit the M8x40mm bolts (Fig. 2).
NOTE: the shorter connection fittings and M8x25mm bolts will not be required.
- Add appropriate elbows or 1/2” BSP nipples to allow for hot/cold water connections (not supplied).
- Secure Floormount Mixer Valve to coggin using appropriate wood screws (not supplied).
NOTE: “FRONT” to face water vessel.
- Complete hot/cold water connections.
- Ensure the valve is level and well anchored.
- Connect 1/2” elbows (or male/female nipples) to Fixing Valve in preparation for the hot/cold water lines.
- Postion fixing valve into concreted recess area.
NOTE: Align “Front” to face bath or wash vessel.
- Mark and drill for 8mm “dyna bolt” or other appropriate anchoring bolts (not supplied).
- Fix Floormount Fixing Valve and complete hot and cold water line connections.
- Ensure the valve is level and well anchored.
- Tighten “end caps” and perform water testing, and ensure there are no water leaks.
- Leave end caps, pressure plate and fixing bolts in the valve to protect the threads until final fit-off.
- Once all water connections are made and tested, fill in the recessed area and channelling up to the
Fixing Valve with a mortar mix.
- After mortar has set, seal the area between mortar and the Fixing Valve.
sussextaps.com.au
2
SUSSEX
INFO & INSTALL GUIDES
CONCEPTS
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
INFORMATION SHEET
Calibre Basin Mixer
Product code: CBM
160
80
100
40
35
48
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
Calibre Basin Mixer
Product code: Available options:
CBM Basin Mixer
CEBM Extended Basin Mixer
INSTALLATION GUIDE
PLUMBER NOTE
-On-site testing using higher water pressures must be
conducted with the Mixer in the closed position.
(STATIC TEST )
-Under no circumstances is the Mixer to be opened
when exceeding the maximum stated water pressure.
-At the completion of testing, do not relieve any high
water pressure by operating the Mixer.
-Exposing the internals of the Mixer Cartridge to higher
than specified water pressures will void the
manufacturers warranty.
INSTALLATION GUIDELINES
-The Mixer is supplied assembled, only the Fixing nut
and the Clamp need to be removed.
-After removing the mentioned parts, lower the Mixer
on to the mounting surface and fit the Flexible Hoses.
-In some cases the Flexible Hoses may need to be fed
through from under the mounting surface and then
attached. (Tighten using appropriate spanner)
-After securing the Flexible Hoses, fit Clamp and attach
the Fixing Nut from underneath.
-Before fully securing the Mixer ensure that the Base O
Ring is intact and the Mixer is properly centered over
the mounting surface hole.
-The Mixer mounting surface must be completely sealed
and water-tight.
-The 1/2” Fittings of the Flexible Hoses have a conical
seal, ensure that the matching threads are cut square
and burr free.
-Prior to connecting the Flexible Hoses, ensure all
pipework is thoroughly flushed and ensure pipework is
free of any dirt or debri.
-Isolating Stop Valves are recommended with all
installations. (not supplied)
-Connect the Flexible Hoses to Hot and Cold pipework
fittings, ensure the Hoses do not kink or become
twisted when tightening.
-Check all fittings and connections are secure and
water-tight.
BASE
O-RING
CLAMP
Hole Size
32-35mm
50mm Max.
Bench thickness
1/2" BSP Fittings
with conical Seals FLEXIBLE HOSES
FIXING
NUT
CONCEPT One
SUSSEX FLOORMOUNT CYLINDER
SUSSEX FLOORMOUNT COVER FLANGE
GSUSSEX FLOORMOUNT FITTIN
20mm
M8 BOLT (X4)
TILE
GLUE
WATER PROOF
C
H
APPL Y SEAL ANT
PRESSURE
PLATE
LEVELLING
SCREWS
FI G 5 MI XE R
SUSSEX FLOORMOUNT COVER FLANGE
SUSSEX FLOORMOUNT CYLINDER
20mm
APPROX
FI G 6 MIXER
FINI SHED
FLOOR SURFACE
NO TE :
“FRONT ” TO
FACE WASH
VESSEL
Voda
Floormount mixer Concrete floor Fit-off
Fit-off (Concrete floor)
- Prior to installing, ensure floor around fixing valve is completely sealed.
- Raise the floormount cover flange.
- Remove “end caps” and retain if required.
- Connect hot and cold hoses from Floormount Mixer (a second person may be required to assist).
NOTE: the hose connection has a self sealing fitting. No sealant is required.
- Tighten the hex nuts of the hose fittings using an appropriate spanner (tighten well).
- Carefully lower the mixer to meet the pressure plate.
NOTE: “Front” of Floormount Mixer must face the bath or wash vessel.
- Align and fit supplied M8 bolts.
- Before fully tightening, allow water flow and check for water leaks.
- Tighten M8 bolts and check Floormount Mixer is level. If levelling is required, loosen M8 bolts and
adjust levelling screws as required.
- To complete the installation, lower the cover flange until it meets the finished floor surface.
- Check mixer function and look for any leaks.
sussextaps.com.au
2
SUSSEX
INFO & INSTALL GUIDES
CONCEPTS
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
INFORMATION SHEET
Calibre Basin Mixer
Product code: CBM
160
80
100
40
35
48
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
Calibre Basin Mixer
Product code: Available options:
CBM Basin Mixer
CEBM Extended Basin Mixer
INSTALLATION GUIDE
PLUMBER NOTE
-On-site testing using higher water pressures must be
conducted with the Mixer in the closed position.
(STATIC TEST )
-Under no circumstances is the Mixer to be opened
when exceeding the maximum stated water pressure.
-At the completion of testing, do not relieve any high
water pressure by operating the Mixer.
-Exposing the internals of the Mixer Cartridge to higher
than specified water pressures will void the
manufacturers warranty.
INSTALLATION GUIDELINES
-The Mixer is supplied assembled, only the Fixing nut
and the Clamp need to be removed.
-After removing the mentioned parts, lower the Mixer
on to the mounting surface and fit the Flexible Hoses.
-In some cases the Flexible Hoses may need to be fed
through from under the mounting surface and then
attached. (Tighten using appropriate spanner)
-After securing the Flexible Hoses, fit Clamp and attach
the Fixing Nut from underneath.
-Before fully securing the Mixer ensure that the Base O
Ring is intact and the Mixer is properly centered over
the mounting surface hole.
-The Mixer mounting surface must be completely sealed
and water-tight.
-The 1/2” Fittings of the Flexible Hoses have a conical
seal, ensure that the matching threads are cut square
and burr free.
-Prior to connecting the Flexible Hoses, ensure all
pipework is thoroughly flushed and ensure pipework is
free of any dirt or debri.
-Isolating Stop Valves are recommended with all
installations. (not supplied)
-Connect the Flexible Hoses to Hot and Cold pipework
fittings, ensure the Hoses do not kink or become
twisted when tightening.
-Check all fittings and connections are secure and
water-tight.
BASE
O-RING
CLAMP
Hole Size
32-35mm
50mm Max.
Bench thickness
1/2" BSP Fittings
with conical Seals FLEXIBLE HOSES
FIXING
NUT
CONCEPT One
40mm
APPROX
FLOORMOUNT MIXER
FLANGE
FINISHED
FLOOR SURFACE
FI G 6
FR O NT
40mm
APPROX
C
H
TILE
GLUE
WATER
PROOF
19mm
PARTICLE
BOARD
FLOORMOUNT MIXER
FLOORMOUMT COVER FLANGE
M8 BOLT (X4)
FLOORMOUNT FITTING
LEVELLING
SCREW
NOGGIN
JOIST JOIST
FI G 5
APPLY SEAL ANT
NOTE:
“FRONT” TO
FACE WASH
VESSEL
FLOORMOUNT COVER
Voda
Fit-off (Wooden floor)
- Prior to installing, ensure floor around fixing valve is completely sealed.
- Raise the floormount cover flange.
- Remove “end caps” and retain if required.
- Connect hot and cold hoses from Floormount Mixer (a second person may be required to assist).
NOTE: the hose connection has a self sealing fitting. No sealant is required.
- Tighten the hex nuts of the hose fittings using an appropriate spanner (tighten well).
- Carefully lower the mixer to meet the pressure plate.
NOTE: “Front” of Floormount Mixer must face the bath or wash vessel.
- Align and fit supplied M8 bolts.
- Before fully tightening, allow water flow and check for water leaks.
- Tighten M8 bolts and check Floormount Mixer is level. If levelling is required, loosen M8 bolts and
adjust levelling screws as required.
- To complete the installation, lower the cover flange until it meets the finished floor surface.
- Check mixer function and look for any leaks.
Floormount mixer Wooden floor Fit-off
sussextaps.com.au
2
SUSSEX
INFO & INSTALL GUIDES
CONCEPTS
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
INFORMATION SHEET
Calibre Basin Mixer
Product code: CBM
160
80
100
40
35
48
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
Calibre Basin Mixer
Product code: Available options:
CBM Basin Mixer
CEBM Extended Basin Mixer
INSTALLATION GUIDE
PLUMBER NOTE
-On-site testing using higher water pressures must be
conducted with the Mixer in the closed position.
(STATIC TEST )
-Under no circumstances is the Mixer to be opened
when exceeding the maximum stated water pressure.
-At the completion of testing, do not relieve any high
water pressure by operating the Mixer.
-Exposing the internals of the Mixer Cartridge to higher
than specified water pressures will void the
manufacturers warranty.
INSTALLATION GUIDELINES
-The Mixer is supplied assembled, only the Fixing nut
and the Clamp need to be removed.
-After removing the mentioned parts, lower the Mixer
on to the mounting surface and fit the Flexible Hoses.
-In some cases the Flexible Hoses may need to be fed
through from under the mounting surface and then
attached. (Tighten using appropriate spanner)
-After securing the Flexible Hoses, fit Clamp and attach
the Fixing Nut from underneath.
-Before fully securing the Mixer ensure that the Base O
Ring is intact and the Mixer is properly centered over
the mounting surface hole.
-The Mixer mounting surface must be completely sealed
and water-tight.
-The 1/2” Fittings of the Flexible Hoses have a conical
seal, ensure that the matching threads are cut square
and burr free.
-Prior to connecting the Flexible Hoses, ensure all
pipework is thoroughly flushed and ensure pipework is
free of any dirt or debri.
-Isolating Stop Valves are recommended with all
installations. (not supplied)
-Connect the Flexible Hoses to Hot and Cold pipework
fittings, ensure the Hoses do not kink or become
twisted when tightening.
-Check all fittings and connections are secure and
water-tight.
BASE
O-RING
CLAMP
Hole Size
32-35mm
50mm Max.
Bench thickness
1/2" BSP Fittings
with conical Seals FLEXIBLE HOSES
FIXING
NUT
CONCEPT One
FR ON T
FR ON T
FR ON T
FR ON T
FR ON T
FR ON T
FR ON T
FR ON T
F/MOUNT MIXER F/MOUNT MIXER F/MOUNT MIXER
STRAIGHT
F/MOUNT MIXER
STRAIGHT
F/MOUNT W/
HAND SHOWER
F/MOUNT W/
HAND SHOWER
F/MOUNT W/
HAND SHOWER
F/MOUNT W/
HAND SHOWER
NOTE:
Handpiece
must be fixed
to rear of the
mixer body
NOTE:
Handpiece
must be fixed
to rear of the
mixer body
NOTE:
Handpiece
must be fixed
to rear of the
mixer body
NOTE:
Handpiece
must be fixed
to rear of the
mixer body
Voda
Floormount mixer Installation kit Fit-off
sussextaps.com.au
-
1
-
2
-
3
-
4
-
5
-
6
The SUSSEX VFMT is a floormount mixer with a 5.0-liter water rating, which ensures water efficiency. It comes with various fixing distances, allowing you to choose the best fit for your bathroom setup. The mixer features a durable construction and can be used with both concrete and wooden floors. Installation requires rough-in and fit-off processes. Detailed instructions for both types of flooring are provided in the manual. Once installed, the mixer offers precise water control and adds a touch of sophistication to your bathroom.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
SUSSEX Circa User manual
-
-
-
SUSSEX RBM-72 Operating instructions
-
-
-
-
SUSSEX Calibre Basin Mixer Bathroomware Owner's manual
-
SUSSEX RBM Installation guide
-
SUSSEX DPTMHM Installation guide
Other documents
-
ROGERSELLER 3639000101 Floormount Basin Outlet Installation guide
-
aquabrass loveme 32085 Installation guide
-
-
-
Kalia BF1934 User guide
-
Kalia BF1998 User guide
-
Eaton Magnum DS Series Instructional Leaflet
-
A&E 240161 Installation guide
-
Unbranded 160405 User manual
-
Pfister Savannah 801-SVHC Specification and Owner Manual
