Page is loading ...
Sideboard
1/25
2/25
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!
Please prepare the following tools
with similar shapes can be distinguished by size
each screw corresponds to the manual, accessories
When installing, please carefully confirm whether
3/25
12 3
4 5 6
78910
11 12 13 14
4/25
17 1816
15
19 20 21 22
25 262423
5/25
1
2
3
4
5
6
7
8
9
10
11
11
12
13
13
14
15
15
16
16
17
6/25
18
19
20
20
21
21
22
23
24
25
26
7/25
1
A
AA
A
A
AB
D
C
DDDD
D
B
D
D
D
A
A
A
A
A
A
A
C
D
B
D
DD
D
D
3
3
44
8/25
180°
180°
Please pay attention to the holes
where the accessories are inserted
and don't use an electric
screwdriver or use force to
Fix slide rail(B) and (C) to both sides of No.3
plate with screw(D) as shown.
Fix slide rail(B) and (C) to both sides of No.4
plate with screw(D) as shown.
Insert quickfit screw(A) into No.3 and No.4 plates as shown.
rotate, may cause crack.
2
A
A
B
D
DD
A
AC
D
D
D
A
3
B
D
D
D
E
E
E
E
2
5
7
8
10
9/25
Fix slide rail(B) and (C) to No.2 and No.5
plates respectively with screw(D) as shown.
Insert quickfit screw(A) into No.2, No.5
plates as shown.
Please pay attention to the holes where the
accessories are inserted and don't use an electric
screwdriver or use force to rotate,
may cause crack.
Hammer part(E) into the corresponding holes of No.8, No.7 and No.10
plates as shown.
4
IIIIII
180
F
G
A
F
F
F
F
FF
F
F
G
G
G
G
G
G
G
3
4
8
9
10/25
Attach No.4 and
No.3 plates to No.8
and No.9 plates
with wooden
dowel(F) and turn
cam locks(G) clockwise
to tighten as shown.
5
IIIIII
F
F
FF
G
G
GG
180
G
F
A
2
3
7
11/25
Connect No.2 and No.7 plates to No.3 with
wooden dowel(F) and turn cam locks(G)
clockwise to tighten as shown.
6
IIIIII
180
G
F
A
F
F
FF
G
G
GG
4
5
10
12/25
Connect No.5 and No.10 plates to No.4
with wooden dowel(F) and turn cam
locks(G) clockwise to tighten as shown.
7
A
A
A
A
A
A
A
A
A
1
13/25
Insert quickfit screw(A) into No.1 plate
as shown.
Please pay attention to the holes where
the accessories are inserted.
8
IIIIII
GG
GG
F
F
F
F
F
F
FF
F
G
180
A
1
2
3
4
5
14/25
Cover No.1 plate to the component with
wooden dowel(F) and turn cam locks(G)
clockwise to tighten as shown.
9
2
3
4
5
15
15
16
16
17
15/25
Slide No.15 and No.16 plates into available
slots as shown.
Please note two No.16
plates are connected with
No.17 bar.
10
F
F
F
F
F
F
F
F
H
H
H
H
H
H
H
H
H
2
3
4
5
6
16/25
Cover No.6 plate to
the component with
wooden dowel(F)
at first, then use
screw(H) to fix as
shown.
11
JJ
12
6
13
13
13
13
14
14
17/25
Rotate part(J) into the support leg
14 as shown.
Rotate leg 13 and support leg 14 into
No.6 plate as shown.
13
K
K
K
K
K
14
M
M
L
N
P
L
MML
M
M
P
N
2
3
4
5
11
11
12
18/25
Fix hinge(L) to
No.12 plate with
Insert part(K) into No.2, 3, 4 and 5
plates, put shelf No.11 as shown.
screw(M), fix
handle(N) with
screw(P) as shown.
15
M
M
M
M
M
M
L
2
3
4
5
12
12
12
12
19/25
Attach No.12 plate to the unit by
fixing hinge with screw(M) as shown.
16
20/25
/
