Page is loading ...
Version:05/05/2023 1/27
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!
2/27
2
60
425 mm
7 x 35 mm
E x 5 F x 5
4 x 16 mm
3.5 x 12 mm
I x 42
5 x 40 mm
Jx2
L x 10
350 mm
3/27
4
1
9
8
2
7
6
3
5
10
11
12
39
38 37
37
26
36 32
35
33
27
34
35
28
31
30
30
29
21
17
17
18
13
18
22
25 14
23
23
23
19
19
19
25
25
25
20
15
15
16
24
4/27
This is a permanent label.
Do not remove!
ALWAYS install tipover restraint
provided.
NEVER put a TV on this product.
NEVER allow children to stand,climb
or hang on drawers,doors,or shelves.
NEVER open more than one drawer
at a time.
Place heaviest items in the lowest
drawers.
1B x 4
13
B
B
B
B
B
2
12 x 10 mm
A x 4
Insert quickfit screw(B) into corresponding
holes in board 13 with a screwdriver as
shown.
Please pay attention to the holes where
the accessories are inserted.
13
Attach board 13 to board 17,18 and turn cam
locks(A) clockwise to tighten as shown.
7 x 40 mm
A
A
A
A
A
A
180°
17 13
18
5/27
3
4
Slide board 24 into available slots.
Attach board 17,18 to board 21
with screw(I) as shown.
17
13
18
24
17
13
18
24
I
I
I
I
21
I
I
x 40 m5m
I x 4
6/27
Attach board 14 to board 17,18 and turn cam
locks(A) clockwise to tighten as shown.
mmx7
5
B x 4
40
6
14
BB
BB
B
14
Insert quickfit screw(B) into corresponding
holes in board 14 with a screwdriver as
shown.
Please pay attention to the holes where
the accessories are inserted.
12 x 10 mm
A x 4
A
A
A
A
A
A
180°
17
14
18
7/27
Slide board 25 into available slots.
7
8
Attach board 17,18 to board 22
with screw(I) as shown.
17 14
18
25
17 14
18
25
22
I
I
I
I
I
I
I x 4
x 40 m5m
8/27
Attach board 15 to board 19,20 and turn cam
locks(A) clockwise to tighten as shown.
9
7 x 40 mm
B x 8
10
15
BB
BB
B
15
x2
x2
Insert quickfit screw(B) into corresponding
holes in board 15 with a screwdriver as
shown.
Please pay attention to the holes where
the accessories are inserted.
12 x 10 mm
A x 8
A
A
A
A
A
A
180°
19
15
20
9/27
Slide board 25 into available slots.
11
12
x2
x2
Attach board 19,20 to board 23
with screw(I) as shown.
19 15
20
25
19 15
20
25
23
I
I
I
I
I
I
I x 8
x 40 m5m
10/27
13
14
Insert quickfit screw(B) into corresponding
holes in board 16 with a screwdriver as
shown.
Please pay attention to the holes where
the accessories are inserted.
16
BB
BB
B
16
12 x 10 mm
A x 4
Attach board 16 to board 19,20 and turn cam
locks(A) clockwise to tighten as shown.
A
A
A
A
A
A
180°
19
16
20
B x 4
7 x 40 mm
11/27
15
16
Slide board 25 into available slots.
Attach board 19,20 to board 23
with screw(I) as shown.
19 16
20
25
19 16
20
25
23
I
I
I
I
I
I
I x 4
x 40 m5m
12/27
17
L1 x 10
350mm
L1(R)
F
E
E
E
E
E
F
F
F
F
L1(L)
13
14
15
15
16
F x
4 x 16 mm
E x 5
5
3.5 x 12 mm
G x 20
G
G
G
G
G
Fix runner(L1) to each side of the drawer with screw(G) as shown.Pay
attention to the runner's installation direction(The circular track
grooves is on the right.).Fix knob(E) with screw(F) as shown.
GG
L1(R)
L1(L)
(R)
L1(L) G
G
L1(L) G
G
L1(L) G
G
L1(L) G
G
G
G
L1(R)
G
G
L1(R)
G
G
L1(R)
G
G
L1(R)
13/27
19
Note:Only this
slider hole is
different.
23
4
G
G G
G G
L2
L2
L2 G
18
Fix slide rail(L2) to board 2,3,4 with
screw(G) as shown.
Please pay attention to the holes where
the accessories are inserted.
G
L2
G
G
G
G
G
G
G
G
G
G
L2
L2
L2
L2
L2
G
G
L2
G
G
L2 G
3.5 x 12 mm 350mm
3.5 x 12 mm 350mm
G x 18 L2 x 9
4
4
G
G
G
L2
L2
Fix slide rail(L2) to board 4 with
screw(G) as shown.
Please pay attention to the holes where
the accessories are inserted.
14/27
21
Insert quickfit screw(B) into corresponding
holes in board 2,3,4
with a screwdriver as shown.
Insert quickfit screw(B) into corresponding
holes in board 4 with a screwdriver
as shown.
23
4
20
B x 3
4
4
L2
15/27
I x 3
12 x 10 mm 5 x 40 mm
A x 3
I
I
I
I
I
22
16/27
I x 5
x 40 m5m
I x 4
x 40 m5m
180°
17/27
23
24
Slide board 12 into available
slots as shown.
Insert quickfit screw(B) into board 1
with a screwdriver as shown.
B
18/27
25
26
B
180°
Cover board 1 into the component
and turn cam locks(A) clockwise to tighten as shown.
19/27
27
Mount
Montaje
La monture Cage
Casillero
La Cage Lever
Elever
Levier Runner
Corrdor
Le coulisseau
Separate glides(M) into two parts as shown.
20/27
28
/
