ITC TPN24KK-60012-10-HL Installation guide

TPN24KK-60012-10-HL

Brand: ITC

Model: TPN24KK-60012-10-HL

Type: Installation guide

ITC TPN24KK-60012-10-HL is a high-lumen tape light designed for indoor use. It features a strong adhesive backing for easy installation on various surfaces. The light is dimmable and can be cut to size for customized lengths. It requires a mounting channel or aluminum flat bar for proper heat dissipation and is not suitable for wet locations. The tape light operates on a 24V-110V power supply and comes with a wiring diagram for hassle-free installation.

ITC TPN24KK-60012-10-HL is a high-lumen tape light designed for indoor use. It features a strong adhesive backing for easy installation on various surfaces. The light is dimmable and can be cut to size for customized lengths. It requires a mounting channel or aluminum flat bar for proper heat dissipation and is not suitable for wet locations. The tape light operates on a 24V-110V power supply and comes with a wiring diagram for hassle-free installation.

3030 Corporate Grove Dr.

Hudsonville, MI 49426

Phone: 616.396.1355

itc-us.com

Safety Instructions

• Disconnect power before installing, adding or changing any component.

• To avoid a hazard to children, account for all parts and destroy all packing materials.

• Do not install any luminaire assembly closer than 6” from any combustible materials.

• Lights are not rated for wet location installation.

• Note, this light is susceptible to damage by electrostatic discharge, use care when handling.

• For safety purposes, ITC recommends tape light installations be used with a Class 2 power device.

For installations without a Class 2 power device, it is highly recommended that appropriate fusing

be used, to be determined by tape light length.

1. Determine the installation location and clean the surface using

alcohol wipes (not provided). For more information on surface

prep please review the 3M website*. Start at the wired end and

begin peeling back the tape.

3. Follow the wiring diagram below to wire the light to your system.

2. Remove paper backing from tape before placing in track then

press the light into the aluminum mounting channel or onto a

piece of 0.1”H x 1/2”W (3mm x 12mm) aluminum ﬂat bar.

Continue working along the light and peeling the paper as you

go. Only pull back a few inches at a time to prevent the tape

light sticking to itself.

In order to properly dissipate the heat, the tape light must be

installed in/on an aluminum channel or ﬂat bar. Failure to

properly install light will void the warranty.

Tape Light

Red (+)

Black (-)

Green (G)

Power Supply

24V - 110V

Neutral (N)

Load (L)

To 110V - 277V

Power

Positive (+)

Negative (-)

*http://www.3m.com/3M/en_US/bonding-and-assembly-us/resources/full-story/?sto-

ryid=b3996cbd-9954-455f-8e72-88e452ca38c0

PARTS / TOOLS NEEDED:

High Lumen Tape Light Mounting Channel

(purchased separately)

UL Class 2 Power Supply

(purchased separately)

Butt Splices

(not provided)

Alcohol Wipes

(not provided)

INSTALLATION INSTRUCTIONS

Tory™ High Lumen

Tape Light

Part#: TPN24KK-60012-10-HL

For warranty information please visit www.itc-us.com/warranty-return-policy

DOC #: 710-00072 • Rev B • 10/16/18

Page 1 of 1

1

ITC TPN24KK-60012-10-HL Installation guide

TPN24KK-60012-10-HL

Brand: ITC

Model: TPN24KK-60012-10-HL

Type: Installation guide

ITC TPN24KK-60012-10-HL is a high-lumen tape light designed for indoor use. It features a strong adhesive backing for easy installation on various surfaces. The light is dimmable and can be cut to size for customized lengths. It requires a mounting channel or aluminum flat bar for proper heat dissipation and is not suitable for wet locations. The tape light operates on a 24V-110V power supply and comes with a wiring diagram for hassle-free installation.

Download PDF

Related papers

Other documents