ITC Acute Flex Light User manual

Acute Flex Light

Brand: ITC

Model: Acute Flex Light

Type: User manual

ITC Acute Flex Light is a versatile lighting solution for various indoor applications. With its bendable design and adhesive backing, it can be easily installed on any clean surface. The light emits a bright and even illumination, making it ideal for task lighting, accent lighting, or decorative purposes. It operates on a 24V-110V power supply and can be wired to a 12V DC or 110V-277V power source. The light is designed for indoor use only and should not be installed closer than 6 inches from combustible materials.

ITC Acute Flex Light is a versatile lighting solution for various indoor applications. With its bendable design and adhesive backing, it can be easily installed on any clean surface. The light emits a bright and even illumination, making it ideal for task lighting, accent lighting, or decorative purposes. It operates on a 24V-110V power supply and can be wired to a 12V DC or 110V-277V power source. The light is designed for indoor use only and should not be installed closer than 6 inches from combustible materials.

3030 Corporate Grove Dr.

Hudsonville, MI 49426

Phone: 616.396.1355

itc-us.com

PARTS / TOOLS NEEDED:

Acute Tape Light UL Approved Power Supply

(optional) Butt Splices (not provided) Alcohol Wipes (not provided)

Safety Instructions

• Disconnect power before installing, adding or changing any component.

• To avoid a hazard to children, account for all parts and destroy all packing materials.

• Do not install any luminaire assembly closer than 6” from any combustible materials.

• Lights are not rated for wet location installation.

• Note, this light is susceptible to damage by electrostatic discharge, use care when handling.

• For safety purposes, ITC recommends tape light installations be used with a Class 2 power device.

For installations without a Class 2 power device, it is highly recommended that appropriate fusing

be used, to be determined by tape light length.

1. Determine the installation location and clean the surface using

alcohol wipes (not provided). For more information on surface

prep please review the 3M website*. Start at the wired end and

begin peeling back the tape.

3. Follow the wiring diagram below to wire the light to your system.

2. Press the light in place. Continue working along the light and

peel the paper as you go. Only pull back a few inches at a time

to prevent the tape light sticking to itself. The light can be bent

at 90°, but should only be bent as shown below. Bending on the

LEDs or smaller curves could result in damage to the light.

Tape Light

To 12V DC

Power

Black (-)

Red (+)

Black (-)

Tape Light

Red (+)

Black (-)

Green (G)

Power Supply

24V - 110V

Neutral (N)

Load (L)

To 110V - 277V

Power

Positive (+)

Negative (-)

*http://www.3m.com/3M/en_US/bonding-and-assembly-us/resources/full-story/?story-

id=b3996cbd-9954-455f-8e72-88e452ca38c0

Fuse

INSTALLATION INSTRUCTIONS

Acute™ Flex Light

Part#: TPMVVKK-LLL12

For warranty information please visit www.itc-us.com/warranty-return-policy

DOC #: 710-00030 • Rev A • 09/11/17

Page 1 of 1

1

ITC Acute Flex Light User manual

Acute Flex Light

Brand: ITC

Model: Acute Flex Light

Type: User manual

ITC Acute Flex Light is a versatile lighting solution for various indoor applications. With its bendable design and adhesive backing, it can be easily installed on any clean surface. The light emits a bright and even illumination, making it ideal for task lighting, accent lighting, or decorative purposes. It operates on a 24V-110V power supply and can be wired to a 12V DC or 110V-277V power source. The light is designed for indoor use only and should not be installed closer than 6 inches from combustible materials.

Download PDF

Related papers

Other documents