Garden Oasis Steel Round Gazebo Owner's manual

Brand: Garden Oasis

Model: Steel Round Gazebo

Type: Owner's manual

Garden Oasis Steel Round Gazebo lets you enjoy the outdoors while protecting you from the elements. With its sturdy steel frame and weather-resistant canopy, this gazebo is built to last. The adjustable canopy provides shade on sunny days, while the built-in lighting allows you to enjoy your evenings outdoors. The gazebo also features retractable mosquito netting, so you can keep the bugs out while enjoying the fresh air. With its easy assembly and versatility, the Garden Oasis Steel Round Gazebo is the perfect addition to any backyard or patio.

Owner’s Manual

Date of Purchase: _____/ _____/ _____

Steel Round Gazebo

Product Code: D71 M11969

KSN: 03975385-0

UPC Code: 805670021153

See our extensive assortment of outdoor living products

on-line at www.sears.com and www.kmart.com

Made in / Hech en CHINA

Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179

Assembly Instrucon for Round Gazebo

(GFM00330F)

***CAUTION:

The remote control is not water resistant! During severe or

inclement (Rain, Snow, Wet...) weather, you must keep it indoors!

Part List

Qty

Image

Description

Beam

Beam with Screw

Holder

Cambered Rail

Long Slide Bar

Short Slide Bar

Post

Folding Canopy

Canopy Cover

Support Bar

Canopy Cover

Attachment Tube

Solar Panel

Beam Hub

Light Cover

Light

Rail Connect

Post Holder

Base

Canopy Handle

Netting

Canopy Cover

Side Wall

Nut and Washer

Plastic Ring

Descripon

Plasc Washer

for Slide Bars

Screw & Nut

Screw

Nut Wrench

Magnec Plate

Allen Wrench

Light Control

with Holder

Slide Bar Holder

Plasc Grove

Countersunk

Screw

Ground Stake

Wrench

Part List

Qty

Image

Fig 1

Fig 2

Step1:

1. Lay down all 6pcs Cambered Rails (C) in a cycle. Insert all 6pcs Rail Connecters (N) into the end of

Cambered Rails (C), keep screw holes straight, as shown in Fig.1

2. Secure all 6pcs Post Holder (O) to the Cambered Rails (C) with Allen Wrench (Z6)

and M6x15mm Screws (Z), as shown in Fig. 2.

3. Turn over the circle structure as shown in Fig.3. DO NOT PUT ANY WEIGHT OR PRESSURE ON

THE STRUCTURE.

Fig 3

Step 1

Fig 1

Fig 2

Fig 4

Fig 3

Step2:

1. Connect all 5pcs of Beams (A) and 1pc of Beam with Screw Holder (B) to Beam Hub (K). Use

1pc M6x15 Screw (Z) to secure each beam to Beam Hub (K), as shown in Fig.1 & Fig.2

2. This step requires 2 people to li the Roof structure onto the circle structure. Have one hold

the roof structure and the other person aach the booms of Beams (A) and Beam with

Screw Holder (B) to the top of Post

Holder (O), using M6x45 Screw (Z1). Refer to Fig.3

3. Connect Magnec Plate (Z5) with the inner part of Cambered Rail (C) right below the Beam

with Screw Holder (B) using M6x8 Screws (Z3).

Refer to Fig.4

Step 2

Fig 1

Fig 2

Fig 3

Fig 5

Step3:

1. Insert the boom rib (the one without wheel) of the Canopy (G) into the boom of Beam with

Screw Holder (B), as shown in Fig.1

Connect the top rib of the Canopy (G) onto the top of Beam with Screw Holder (B) with M5x15

Screw and Nut (X), as shown in Fig.2

2. Place the ribs with wheels onto the Cambered Rail (C), as Shown in Fig.3 & Fig.4. (Make sure all

the wheels are on the back side of the magnec plate (Z5).

3. Thread

the wire of the Canopy (G) through the top of the Beam Hub (K). As shown in Fig.5.

Secure the Canopy (G) and Beam Hub (K) with a Nut and Washer (U), using Nut Wrench (Z) on the top of

the Beam Hub (K) and Wrench (Z12) under the Canopy (G). Tighten them as shown in Fig.6

Step 3

Fig 4

Fig 6

12Z

Fig 1

Fig 2

Step4:

1. With one person holding the Light (M), another person connect the two wires as shown

in Fig.1

2. Secure the Light (M) under the Folding Canopy (G) by inserting 2pcs M6x15 Screws(Z)

through the bracket and into the top of the Light(M). As shown in Fig.2

Step 4

Fig 4

Fig 3

Fig 2

Step5:

1. Insert the 2pcs Canopy Cover Attachment Tube (I) into Canopy Cover (S) as shown in Fig.1.

Attach the Canopy Cover (S) to the Beams (A & B) with 3pcs M6x15 Screws (Z) on each Beam. As

shown in Fig.3 & Fig.4

2. Connect the Canopy Cover Support Bar (H) onto the end of Beam (B) and Beam (A) with

M6x15 Screw (Z). Attach the end of Canopy Cover (S) to the Canopy Cover Support Bar (H) using

the veko on the bottom of the Canopy Cover (S) . As shown in Fig.2

Step 5

Fig 1

Fig 4

Fig 3

Fig 2

Fig 1

Step6:

*** Take out Solar Panel (J), Be sure to turn on the Solar Panel (J) (Press the red button) ,

as shown in Fig.1

1. Thread the wire on the Solar Panel (J) into the big hole of the Light Cover (L). Connect

the Solar Panel (J) and Light Cover (L) with 1pc M6x15 (Z). As shown in Fig.2

2. Connect the wire on the Solar Panel (J) and the wire on the Light (M) in the Beam Hub

(K). As shown in Fig.3

3. Lay the Solar Panel (J) and Light Cover (L) onto the top of Beam Hub (K). Keep the

screw holes straight and secure the Light Cover (L) onto the beams with 2pcs M6x15 Screws

(Z). As shown i

n Fig.4

*** Once the Solar Panel (J) and Light (M) is connected, you can try the remote control.

If the light turns on, then it works. Otherwise, please check the wiring and make sure

the Solar Panel (J) is turned "on".

Step 6

Fig 1

Fig 2

Fig 3

Step7:

1. Attach the Canopy Handle (Q) onto the first outer rib on the front of Folding Canopy (G)

with M5x25 Screw and Nut (Y). Make sure the magnet on the handle can be adhered onto the

rail. Refer to Fig.1

2. Lay down the Post (F), and insert it into the Base (P). Align the screw holes and secure

the Base (P) and Post (F) with M6x15 Screw (Z). Do the same for the other 5pcs Posts.

Refer to Fig.2

3. Attach the Slide Bar Holder (Z8) to the top of all 6pcs Posts (F) with M6x68 Screw

(Z2). Refer to Fig.3

Step 7

Fig 1

Fig 2

Fig 3

Step8:

*** This step requires 6 people and 6 step ladders

1. Put 6 Posts (F) vertically and close to the Post Holder (O) on the roof structure.

have 6 person lift the roof onto the Post (B). Adjust the Post's position to ensure the screw holes

are in line with Post Holder (F).

2. Secure the Posts (F) to Post Holder (O) with 5pcs M6x15 Screws (Z) on each Post (F).

Refer to Fig.1

Also tighten the screws on the Cambered Rail (C) one more time in case the screw in the

connection part loosen during moving and assembling.

3. Insert Plastic Groves (Z9) into the holes on the Post (F) ( the one has 2 extra screw holes )

as shown in Fig.2; Install the Light Control Holder (Z7) on the Post (F). Push the Countersunk Screw

(Z10) through the Light Control Holder (Z7) an

d into the Post (F). Refer to Fig.3

Step 8

Fig 1

Fig 3

Fig 4

1. Take out 1pc Short Slide Bar (E) and 1pc Long Slide Bar (D), connect the two

slide bars with M6x68 Screw (Z2) in the middle of bars. Make sure there is a Plastic

Washer (W) between two bars and a plastic Washer (W) between the Long Slide Bar

(D) and Cambered Rail (C). As shown in Fig.1

2. Put the two ends of both Slide Bar (D & E) into the Slide Bar holder (Z8) , as

shown in Fig.3 & Fig.4. Tighten the M6x68 Screw (Z2) in the middle of slide bars to

secure the slide bars to the Cambered Rail (C), as shown in Fig.2. Do the same for other

5 sets of slide bars.

Step 9

Fig 2

Fig 1

Fig 3

1. Put the Plastic Rings (V) into the holes on the top of Sidewalls (T) and Nettings (R).

Hang the Sidewall (T) onto the Long Slide Bar (D) which is closer to the Cambered Rail (C) as

shown in Fig.1. Hang the Netting onto Short Slide Bar (E), as shown in Fig.2

2. Press down the Ground Stakes (Z11) through the Base (P) into the ground. Refer to Fig.3

Step 10

Garden Oasis Steel Round Gazebo Owner's manual

Garden Oasis Steel Round Gazebo Owner's manual

Garden Oasis Steel Round Gazebo Owner's manual

Related papers

Other documents