aivituvin AIR 53 Rabbit Hutch Bunny House on Wheels Hamster Cage User manual

Type
User manual
INSTRUCTION
MANUAL
AIR 53
www.aivituvin.com
X
Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.
TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
30MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
02
M3.0x16mm SCREW
M3.5x45mm SCREW
12PCS+1spare 18PCS+1spare
1PC
Roof hinge
Latch
1PC
PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
D E F
G
1PC
1PC 1PC
03
HI
1PC
1PC
1PC
1PC
1PC
Front Panel
Back Panel Left Panel
Right Panel
1PC Wooden Floor
Metal Tray
Divider
Wooden Board Bottom Wire Netting
PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
M N
2PCS
1PC 1PC
04
1PC
2PCS Normal casters
Roof
Brake casters
Ramp
Layer
PRODUCT ASSEMBLY
01
02
05
Attach front panel Part A by 6xP1 screws.
Attach side panel Part C & D and divider Part E to back panel Part B
by 6xP1 screws.
P1X
A
B
D
6
C
E
P1X
6
D
C
B
PRODUCT ASSEMBLY
03
04
06
Put in wooden board Part G & bottom wire netting Part H.
G
F
I
H
Put in the wooden floor Part I as show on the picture.
Slide in the tray Part F.
PRODUCT ASSEMBLY
05
06
07
J
K
P
2
X4
P
2
X6
Screw ramp Part K to layer Part J by 4XP2. Then put it in the house.
Attach roof Part L by 6XP2 screws.
L
PRODUCT ASSEMBLY
07
08
08
P
2
X4
Nx2
L
P
3
X1
Mx2
Attach roof hinge P3 by 4XP2 screws.
Attach casters Part M & N to the legs.
PRODUCT ASSEMBLY
09
P4X1
P2X4
09
Attach lock P4 by 4XP2 screws.
WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

aivituvin AIR 53 Rabbit Hutch Bunny House on Wheels Hamster Cage User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI