ASRock Rack D1622D4I User manual

D1622D4I

D1600D4I-2L2T

User Manual

Version 1.0

Published January 2020

Version 1.0

Published January 2020

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Rack Inc.

Products and corporate names appearing in this documentation may or may not

be registered trademarks or copyrights of their respective companies, and are used

only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished

for informational use only and subject to change without notice, and should not

be constructed as a commitment by ASRock Rack. ASRock Rack assumes no

responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock Rack does not provide

warranty of any kind, either expressed or implied, including but not limited to

the implied warranties or conditions of merchantability or tness for a particular

purpose.

In no event shall ASRock Rack, its directors, ocers, employees, or agents be liable

for any indirect, special, incidental, or consequential damages (including damages

for loss of prots, loss of business, loss of data, interruption of business and the

like), even if ASRock Rack has been advised of the possibility of such damages

arising from any defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

ASRock Rack’s Website: www.ASRockRack.com

Contact Information

If you need to contact ASRock Rack or want to know more about ASRock Rack,

you’re welcome to visit ASRock Rack’s website at www.ASRockRack.com; or you

may contact your dealer for further information.

ASRock Rack Incorporation

6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,

Taipei City 112, Taiwan (R.O.C.)

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Unique Features 5

1.4 Motherboard Layout 6

1.5 Onboard LED Indicators 8

1.6 I/O Panel 9

1.7 Block Diagram 11

Chapter 2 Installation 13

2.1 Screw Holes 13

2.2 Pre-installation Precautions 13

2.3 Installation of Memory Modules (DIMM) 14

2.4 Expansion Slots (PCI Express Slots) 16

2.5 Jumper Setup 17

2.6 Onboard Headers and Connectors 18

2.7 ATX PSU / DC-IN Power Connections 23

2.8 Unit Identication purpose LED/Switch 24

2.9 Dual LAN and Teaming Operation Guide 25

2.10 M.2_SSD Module Installation Guide 26

Chapter 3 UEFI Setup Utility 27

3.1 Introduction 27

3.1.1 UEFI Menu Bar 27

3.1.2 Navigation Keys 28

3.2 Main Screen 29

3.3 Advanced Screen 30

3.3.1 CPU Conguration 31

3.3.2 DRAM Conguration 34

3.3.3 Chipset Conguration 35

3.3.4 Storage Conguration 37

3.3.5 ACPI Conguration 38

3.3.6 USB Conguration 39

3.3.7 Super IO Conguration 40

3.3.8 Serial Port Console Redirection 41

3.3.9 H/W Monitor 44

3.3.10 Runtime Error Logging 45

3.3.11 Intel SPS Conguration 47

3.3.12 Instant Flash 48

3.4 Security 49

3.4.1 Key Management 50

3.5 Boot Screen 54

3.5.1 CSM(Compatibility Support Module) 56

3.6 Event Logs 58

3.7 Server Mgmt 59

3.7.1 System Event Log 60

3.7.2 BMC Network Conguration 61

3.7.3 BMC Tools 63

3.8 Exit Screen 64

Chapter 4 Software Support 65

4.1 Download and Install Operating System 65

4.2 Download and Install Software Drivers 65

4.3 Contact Information 65

Chapter 5 Troubleshooting 66

5.1 Troubleshooting Procedures 66

5.2 Technical Support Procedures 68

5.3 Returning Merchandise for Service 68

D1622D4I / D1600D4I-2L2T

PB 1

English

Chapter 1 Introduction

ank you for purchasing ASRock Rack D1622D4I / D1600D4I-2L2T motherboard,

a reliable motherboard produced under ASRock Rack’s consistently stringent quality

control. It delivers excellent performance with robust design conforming to ASRock

Rack’s commitment to quality and endurance.

1.1 Package Contents

• ASRock Rack D1622D4I / D1600D4I-2L2T Motherboard

(Mini-ITX Form Factor: 6.7-in x 6.7-in, 17.02 cm x 17.02 cm)

• 1 x Mini SAS Cable (6G) (60cm)

• 1 x I/O Shield

• 1 x Screw for M.2 Socket

If any items are missing or appear damaged, contact your authorized dealer.

Because the motherboard specications and the BIOS soware might be updated, the con-

tent of this manual will be subject to change without notice. In case any modications of

this manual occur, the updated version will be available on ASRock Rack website without

further notice. You may nd the latest memory and CPU support lists on ASRock Rack

website as well. ASRock Rack’s Website: www.ASRockRack.com

If you require technical support related to this motherboard, please visit our website for

specic information about the model you are using.

http://www.asrockrack.com/support/

2 3

English

1.2 Specications

D1622D4I / D1600D4I-2L2T

MB Physical Status

Form Factor Mini-ITX

Dimension 6.7'' x 6.7'' (17.02 cm x 17.02 cm)

Processor System

CPU Supports Intel® Xeon® D 1600 Processor

Chipset Soc

System Memory

Capacity - 4x DDR4 DIMM slots

- Supports up to 128GB DDR4 ECC RDIMM

- Supports up to 64GB DDR4 ECC UDIMM

DIMM Sizes and

Type per DIMM

- ECC UDIMM: 4GB, 8GB, 16GB

- RDIMM: 4GB, 8GB, 16GB, 32GB

Frequency - ECC UDIMM: 1600, 1866, 2133MHz

- RDIMM: 1600, 1866, 2133MHz

Voltage 1.2V

Expansion Slot

PCIe 3.0 x16

1 slot

M.2 1 slot (PCIE, support form factor: 2280)

Storage

SATA Controller 6 x SATA3 6Gb/s (4 port from mini SAS HD, 2 ports SATA

7pin, SATA_4 supports DOM)

Ethernet

Interface 10000 / 1000 /100 Mbps

LAN Controller - 2 x RJ45 GLAN by Intel® i210

- 2 x RJ45 10GLAN by Intel® X557-AT2 (D1600D4I-2L2T only)

- Supports Wake-On-LAN

- Supports Energy Ecient Ethernet 802.3az

- Supports Dual LAN with Teaming function

- Supports PXE

Management

BMC Controller ASPEED AST2500

IPMI Dedicated

GLAN 1 x Realtek RTL8211E for dedicated management GLAN

Features

- Watch Dog

- IPMI (Intelligent Platform Management Interface) v.2.0

- Virtual media over LAN function

- KVM over LAN function

Graphics

Controller ASPEED AST2500

VRAM DDR4 16MB

D1622D4I / D1600D4I-2L2T

2 3

English

Output Supports D-Sub with max. resolution up to 1920x1200 @ 60Hz

Rear Panel I/O

VGA Port 1 x D-Sub

USB 3.2 Gen1

Port 2

LAN Port

- RJ45: 2x 10GLAN(by Intel® X557-AT2 )(D1600D4I-2L2T only) +

2x GLAN(by Intel i210)

- LAN Ports with LED (ACT/LINK LED and SPEED LED)

UID Button/UID

LED 1

Internal Connector

Auxiliary Panel

Header 1 (includes chassis intrusion, 2 front LAN LED, System LED)

SATA DOM 1

SATA DOM

Power 1

SATA Port 2

PSU_SMB1

Header 1

TPM Header 1

Speaker Header 1

Panel Header 1

MiniSAS HD

Connector 1 (SATA_0_3)

USB 2.0 Header 1 (supports 1 USB 2.0 port)

USB 3.2 Gen1

Header 1 (supports 2 USB 3.2 Gen1 ports)

Fan Header 4

ATX Power 1 x (4-pin) + 1 x (8-pin) support 12V DC-IN

SATA SGPIO 1

SATA Power

1 (for DC-IN mode)

*Caution: Misconnection between the ATXPWR1 and the HDDPWR1 con-

nectors may permanently damage the motherboard.

ClearCMOS 1 (short pad)

FanFail LED 4

System BIOS

BIOS Ty pe 16MB AMI UEFI Legal BIOS

BIOS Features

- Plug and Play (PnP)

- ACPI 2.0 Compliance Wake Up Events

- SMBIOS 2.8.0 Support

- ASRock Rack Instant Flash

4 5

English

Hardware Monitor

Temperature - CPU/PCH/DDR/LAN/Storage Temperature Sensing

- MB/Card side Temperature Sensing

Fan

- Fan Tachometer

- Fan Multi-Speed Control

- CPU Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by

CPU Temperature)

Voltage Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,

1.05V_PCH, +BAT, 3VSB, 5VSB

Support OS

OS Linux®

- Red Hat Enterprise Linux Server 7.7 (64 bit) / 8.1 (64 bit)

- CentOs 7.7 (64 bit) / 8.1 (64 bit)

- SUSE Enterprise Linux Server 12 SP4 (64 bit) / 15 SP1 (64 it)

- Fedora 30 (64 bit)

- FreeBSD 11.3 (64 bit)

- Ubuntu 19.10 (64 bit)

* Please refer to our website for the latest OS support list.

Environment

Temperature Operation temperature: 10°C ~ 35°C / Non operation

temperature: -40°C ~ 70°C

* For detailed product information, please visit our website: http://www.asrockrack.com

is motherboard supports Wake from on Board LAN. To use this function, please make

sure that the “Wake on Magic Packet from power o state” is enabled in Device Manager

> Intel® Ethernet Connection > Power Management. And the “PCI Devices Power On” is

enabled in UEFI SETUP UTILITY > Advanced > ACPI Conguration. Aer that, onboard

LAN1&2 can wake up S5 under OS.

If you install Intel® LAN utility, this motherboard may fail Windows® Hardware Quality

Lab (WHQL) certication tests. If you install the drivers only, it will pass the WHQL tests.

D1622D4I / D1600D4I-2L2T

4 5

English

1.3 Unique Features

ASRock Instant Flash is a BIOS ash utility embedded in Flash ROM. is conve-

nient BIOS update tool allows you to update system BIOS without entering operating

systems rst like MS-DOS or Windows®. With this utility, you can press the <F6> key

during the POST or the <F2> key to enter into the BIOS setup menu to access ASRock

Rack Instant Flash. Just launch this tool and save the new BIOS le to your USB ash

drive, oppy disk or hard drive, then you can update your BIOS only in a few clicks

without preparing an additional oppy diskette or other complicated ash utility.

Please be noted that the USB ash drive or hard drive must use FAT32/16/12 le

system.

6 7

English

1.4 Motherboard Layout

CH0_A1 (64 bit, 288-pin module, Blue)DDR4,

CH0_A2 (64 bit, 288-pin module, White)DDR4,

17.0cm (6.7 in)

5

7

6

FAN3

TPM1

AUX_PANEL1

SATAPWR1

1

HDLED RESET

PLED PWRBTN

PANEL1

1

SATA_4

CH1_B1 (64 bit, 288-pin module, Blue)DDR4,

CH1_B2 (64 bit, 288-pin module, White)DDR4,

8

1

PSU_SMB1

9

FAN1

10

BAT1

11

USB_1

SATA_5

FAN4

NUT80

M2_1

D1622D4I

D1600D4I-2L2T

PCIE7

PECI1

1

VGA1

USB 3.2

Gen1

T: USB2

B: USB1

IPMI

LAN

UID1

LAN1 LAN2

1

12

14

13

15

16

17

18

19

20

21

22

25

27

11

SPEAKER1

1

CLRMOS1

USB3_3_4

11

23

AST2500

FAN2

ATX12V1

SATA_0_3

1

CHASSIS_ID0

1

ME_RECOVERY1

1

SATA_SGPIO1

X557-AT2

LAN3 LAN4

1

LED_LAN3_4

23

24

1

26

ATXPWR1

HDDPWR1

4

(D1600D4I-2L2T only)(D1600D4I-2L2T only)

(D1600D4I-2L2T only)

D1622D4I / D1600D4I-2L2T

6 7

English

No. Description

1System Fan Connector (FAN2)

2PSU SMBus (PSU_SMB1)

3SATA Power Connector (HDDPWR1)*

4ATX 12V Power Connector (ATX12V1)

5ATX 4-PIN Power Connector (ATXPWR1(ATX 24pin-to-4pin))*

6System Fan Connector (FAN3)

72 x 288-pin DDR4 DIMM Slots (CH0_A1, CH1_B1)

82 x 288-pin DDR4 DIMM Slots (CH0_A2, CH1_B2)

9System Connector (FAN1)

10 Speaker Header (SPEAKER1)

11 Clear CMOS Pad (CLRMOS1)

12 TPM Header (TPM1)

13 Front LAN LED Connector (LED_LAN3_4)

14 Auxiliary Panel Header (AUX_PANEL1)

15 SATA DOM Power Connector (SATAPWR1)

16 SATA3 DOM Connector (SATA_4)

17 SATA3 Connector (SATA_5)

18 USB 3.2 Gen1 Header (USB3_3_4)

19 System Panel Header (PANEL1)

20 USB 2.0 Header (USB_1)

21 System Fan Connector (FAN4)

22 Mini SAS HD Connector (SATA_0_3)

23 ME Recovery Jumper (ME_RECOVERY1)

24 Chassis ID Jumper (CHASSIS_ID0)

25 SATA SGPIO Connector (SATA_SGPIO1)

26 M.2 Socket (M2_1) (Type 2280)

27 CPU PECI Mode Jumper (PECI1)

*Caution: Misconnection between the ATXPWR1 and the HDDPWR1 connectors may permanently damage the

motherboard.

8 9

English

1.5 Onboard LED Indicators

CH0_A1 (64 bit, 288-pin module, Blue)DDR4,

CH0_A2 (64 bit, 288-pin module, White)DDR4,

FAN3

CH1_B1 (64 bit, 288-pin module, Blue)DDR4,

CH1_B2 (64 bit, 288-pin module, White)DDR4,

1

FAN1

BAT1

FAN4

NUT80

M2_1

11

SPEAKER1

CLRMOS1

AST2500

FAN2

1

X557-AT2

1

2

3

4

65

No. Item Status Description

1FAN_LED2 Amber FAN2 failed

2FAN_LED3 Amber FAN3 failed

3FAN_LED1 Amber FAN1 failed

4FAN_LED4 Amber FAN4 failed

5 SB_PWR1 Green STB PWR ready

6BMC_LED1 Green BMC heartbeat LED

D1622D4I / D1600D4I-2L2T

8 9

English

1.6 I/O Panel

25

3

6

4

1

7 8

No. Description No. Description

1 Dedicated IPMI LAN Port* 5 LAN RJ-45 Port (LAN1)*

2 USB 3.2 Gen1 Ports (USB3_1_2) 6 10G LAN RJ-45 Port (LAN4)**

(D1600D4I-2L2T only)

3 UID Switch/LED (UID1) 7 10G LAN RJ-45 Port (LAN3)**

(D1600D4I-2L2T only)

4 LAN RJ-45 Port (LAN2)* 8 VGA Port (VGA1)

LAN Port LED Indications

*ere are two LED next to the LAN port. Please refer to the table below for the LAN port

LED indications.

Dedicated IPMI LAN Port LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10M bps connection

Blinking Yellow Data Activity Yellow 100M bps connection

On Link Green 1G bps connection

ACT/LINK LED

SPEED LED

LAN Port

10 11

English

**ere are two LEDs on each LAN port. Please refer to the table below for the LAN port

LED indications.

1G LAN Port (LAN1, LAN2) LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection or

no link

Blinking Green Data Activity Yellow 100Mbps connection

On Link Green 1Gbps connection

10G LAN Port (LAN1, LAN2) LED Indications (D1600D4I-2L2T only)

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 100Mbps connection or

no link

Blinking Green Data Activity Yellow 1Gbps connection

On Link Green 10Gbps connection

ACT/LINK LED

SPEED LED

ACT/LINK LED

SPEED LED

D1622D4I / D1600D4I-2L2T

10 11

English

1.7 Block Diagram

5

4

3

2

1

D D

C C

B B

A A

2*rear

LPC BUS

RGMII

PCIe x 16 Gen3

CASE OPEN

D1600D4I-2L2T

Channel B

Intel Processor

SIO

Nuvoton NCT5567

Hewitt Lake –DE

NS D-16XX

PCI-E X16 SLOT7

128-bit Dual-Channel Memory x 4 Slots

DDR4 1866/2133/2400

Channel A

SOC

(system on chip)

X 16

support RDIMM UDIMMs

DRAM

RDIMM: 128GB (32GB Per DIMM)

UDIMM: 64GB (16GB Per DIMM)

NCSI

PCIE x1

Realtek

PHY 8211E

M.2 (2280)

USB2.0

RJ45

CPU Fan x 1

TPM

USB3.0

1*AST2500 ; 1*ASM1074 for U3 HUB

VGA

ASPEEND

AST2500

600MB/S

DDR4 1866/2133/2400

SATA_5

SATA_4 support SATA DOM

Header

3x system Fan

2 front

1 rear

FAN x 4

D-sub

SPI

SPI FLASH

32 Mb for LAN0

600MB/S

No support NGFF card

SATA_0_3 Mini-SAS HD

TR1

X 4

INTEL LAN X557-AT2 (port3/4)

KR0

PCIe x 4 Gen3

USB3.0 1*ASM1074 for U3 HUB USB3.0 2*front U3

1*front U2

Intel I210 (port1)

PCIE x1

Intel I210 (port2)

PCIE x1

SPI

SPI FLASH

32 Mb for LAN1

BIOS

SWITCH

SPI FLASH

128Mb

SPI

Size

Project Name

Rev

Date: Sheet of

Title :

Engineer:

C

298Wednesday, December 25, 2019

02-System block

R1.01

D1600D4I-2L2T

Rex-Chang

Size

Project Name

Rev

Date: Sheet of

Title :

Engineer:

C

298Wednesday, December 25, 2019

02-System block

R1.01

D1600D4I-2L2T

Rex-Chang

Size

Project Name

Rev

Date: Sheet of

Title :

Engineer:

C

298Wednesday, December 25, 2019

02-System block

R1.01

D1600D4I-2L2T

Rex-Chang

12 13

English

5

4

3

2

1

D D

C C

B B

A A

2*rear

LPC BUS

RGMII

PCIe x 16 Gen3

CASE OPEN

D1622D4I

Channel B

Intel Processor

SIO

Nuvoton NCT5567

Hewitt Lake –DE

NS D-16XX

PCI-E X16 SLOT7 128-bit Dual-Channel Memory x 4 Slots

DDR4 1866/2133/2400

Channel A

SOC

(system on chip)

X 16

support RDIMM UDIMMs

DRAM

RDIMM: 128GB (32GB Per DIMM)

UDIMM: 64GB (16GB Per DIMM)

NCSI

PCIE x1

Realtek

PHY 8211E

M.2 (2280)

USB2.0

RJ45

CPU Fan x 1

TPM

USB3.0

1*AST2500 ; 1*ASM1074 for U3 HUB

VGA

ASPEEND

AST2500

600MB/S

DDR4 1866/2133/2400

SATA_4 support SATA DOM

Header

3x system Fan

2 front

1 rear

FAN x 4

D-sub

X1

No support NGFF card

SATA_0_3 Mini-SAS HD

X 4

PCIe x 4 Gen3

USB3.0 1*ASM1074 for U3 HUB USB3.0 2*front U3

1*front U2

Intel I210 (port2)

PCIE x1

Intel I210 (port1)

PCIE x1

SPI

SPI FLASH

32 MB

BIOS

SWITCH

SPI FLASH

16MB

SPI

SATA X 1

SWITCH

SATA_5 share M2

Size

Project Name

Rev

Date: Sheet of

Title :

Engineer:

C

2 98Friday, September 04, 2020

02-System block

R1.02

D1600D4I-2L2T

Rex-Chang

Size

Project Name

Rev

Date: Sheet of

Title :

Engineer:

C

2 98Friday, September 04, 2020

02-System block

R1.02

D1600D4I-2L2T

Rex-Chang

Size

Project Name

Rev

Date: Sheet of

Title :

Engineer:

C

2 98Friday, September 04, 2020

02-System block

R1.02

D1600D4I-2L2T

Rex-Chang

D1622D4I / D1600D4I-2L2T

12 13

English

Chapter 2 Installation

This is a Mini-ITX form factor (6.7'' x 6.7'', 17.0 cm x 17.0 cm) motherboard. Before

you install the motherboard, study the conguration of your chassis to ensure that the

motherboard ts into it.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the chassis.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components or

change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any components.

2. To avoid damaging the motherboard’s components due to static electricity, NEVER

place your motherboard directly on the carpet or the like. Also remember to use a

grounded wrist strap or touch a safety grounded object before you handle the compo-

nents.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-static pad or in

the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard to the chassis,

please do not over-tighten the screws! Doing so may damage the motherboard.

Make sure to unplug the power cord before installing or removing the motherboard. Failure

to do so may cause physical injuries to you and damages to motherboard components.

Do not over-tighten the screws! Doing so may damage the motherboard.

Before you install or remove any component, ensure that the power is switched o or the

power cord is detached from the power supply. Failure to do so may cause severe damage to

the motherboard, peripherals, and/or components.

14 15

English

2.3 Installation of Memory Modules (DIMM)

is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and

supports Dual Channel Memory Technology.

Dual Channel Memory Conguration

Priority CH0_ A1

(Blue)

CH0_A2

(White)

CH1_B1

(Blue)

CH1_B2

(White)

1Populated Populated

2Populated Populated Populated Populated

*Since installing three memory modules is NOT supported on this motherboard, we suggest not using

this conguration.

1. For dual channel conguration, you always need to install identical (the same brand,

speed, size and chip-type) DDR4 DIMM pairs.

2. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot;

otherwise, this motherboard and DIMM may be damaged.

3. Please install the memory module on CH0_A1 for the rst priority.

4. To activate Dual Channel Memory Technology, please follow the “Dual Channel Memory

Conguration” table below.

e DIMM only ts in one correct orientation. It will cause permanent damage to the

motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Page is loading ...

ASRock Rack D1622D4I User manual

Related papers

Other documents