B-K lighting Litestick - Style T Installation guide

Brand
B-K lighting
Model
Litestick - Style T
Type
Installation guide

B-K Lighting Litestick - Style T is a low voltage halogen or LED fixture that can be used for in-ground recessed installation. It is suitable for wet locations and comes with an optional stability flange for added stability. The fixture can be used with a remote transformer or an integral transformer. The adjustable stem allows for customization of the height of the fixture, and the optional stability flange helps to keep the fixture in place. The fixture is easy to install and comes with all the necessary hardware.

B-K Lighting Litestick - Style T is a low voltage halogen or LED fixture that can be used for in-ground recessed installation. It is suitable for wet locations and comes with an optional stability flange for added stability. The fixture can be used with a remote transformer or an integral transformer. The adjustable stem allows for customization of the height of the fixture, and the optional stability flange helps to keep the fixture in place. The fixture is easy to install and comes with all the necessary hardware.

Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
TOOLS
NEEDED:
By Others
5/64” Allen Wrench
Phillips Screwdriver
Waterproof Wire Connectors
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
This set of instructions works for:
LT - Litestick™
LT-L - Litestick™ Style L
LT-T - Litestick™ Style T
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
LT-L
TOOLS
NEEDED:
By Others
18 Gauge Wire
Optional Stability
Flange
Power Pipe™
Adjustable
Stem
Fixed
Stem
DATE
11-30-16
REFERENCE NUMBER
INS001109
Warning Flammable Hot Surface
LT
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when turning on.
Do not touch hot lens, guard, or enclosure
(see diagram/picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth.
Oil from skin may damage lamp.
Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
· SUITABLE FOR WET LOCATIONS · SUITABLE FOR IN-GROUND RECESSED INSTALLATION
IMPORTANT LISTINGS AND CERTIFICATIONS
Fixed Stem
with
T - housing
option
LT-T
& Low Voltage Halogen LT™/ LT-L™/ LT-T™
Installation Instructions
High Voltage
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
& Low Voltage Halogen LT™/ LT-L™/ LT-T™
Installation Instructions
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
DATE
11-30-16
REFERENCE NUMBER
INS001109
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
4. Place Power Pipe™ in hole.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
2. Slide optional Stability Flange onto Power
Pipe™. Use optional Stability Flange to aid in
installation of Power Pipe™.
1. Excavate trench according to designed lighting
plan. Dig hole a minimum of 24” deep and 10”
wide to accommodate Power Pipe™ at desired
fixture locations.
Power Pipe™ Installation
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
5. Back fill with pea gravel or sand as required.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
6. Backfill with soil or prepare for concrete pour.
Label on Power Pipe™ indicates installation
depth with finished grade.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
3. Pull low voltage wiring from remote transformer
(By Others) to Power Pipe™. Allow for additional
cable to make connections to fixture lead and
future service.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
2. Insert additional wires and connectors into
Power Pipe. Place fixture on Power Pipe™.
3. Tighten three (3) #8-32 stainless steel round
head Phillips screws on cap to secure to
installed Power Pipe™.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
1. Make watertight connections from remote
12V transformer to fixture leads using
waterproof wire connectors (By Others).
Adjustable stem includes 60” of addtional
18/2 direct burial low voltage cable.
4. Slide stem up or down to desired height. Delrin
bushing holds stem in position. Tighten three
(3) #10 stainless steel set screws using a 3/32”
Allen wrench to lock mounting height in place.
Unused stem length remains hidden inside
Power Pipe™ to accommodate future landscape
growth.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
Fixed and Adjustable Stem Fixture Installation
For Adjustable Stem Only
LED - For use with 12VAC remote
transformer or magnetic transformers
only. B-K Lighting cannot guarantee
performance with third party manufacturers’
transformers.
Low Voltage - For use with 12VAC remote
transformer.
NOTE: Leave sufficient wire length in the
fixture housing for future service. Do not cut
PVC.
& Low Voltage Halogen LT™/ LT-L™/ LT-T™
Installation Instructions
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
1. Loosen #8-32 stainless steel set screw on cap
using a 5/64” Allen wrench and remove.
THIS PRODUCT IS AVAILABLE WITH A FACTORY INSTALLED LED OR HALOGEN LAMP.
Halogen Lamp or LED Installation - If Required
DATE
11-30-16
REFERENCE NUMBER
INS001109
3. Place cap on fixture and tighten set screw.
Tighten screw to 1/2 inch pounds. Top of
screw should sit flush with fixture cap.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and
will void warranty.
2. Install lamp. For BKSSL: Pull the heat sink
from the body to expose the LED board
and Driver components. Utilize quick
disconnects to change modular LED and
driver components. Re-install the heat sink
into body.
CAUTION…follow lamp manufacturers instructions. Do
not touch lamp glass with bare skin. High temperature
of lamp will cause skin oil to damage glass. Clean lamps
with alcohol, if touched.
Halogen BKSSL
Integral Transformer
1. Pull branch circuit wires necessary for installation
(By Others) through Power Pipe™. Use waterproof
wire connectors (By Others) to connect transformer
primary leads to branch circuit wires. Connect
incoming ground to ground wire provided in
fixture body. See wiring diagram.
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND IN HOUSING
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete
Finished grade
Finished grade Optional
Stability Flange
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND IN HOUSING
2. Insert wires, connectors and/or transformer into
fixture base and attach to Power Pipe™. Tighten
three (3) #8-32 stainless steel round head Phillips
screws at base to secure.
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND IN HOUSING
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete
Finished grade
Finished grade Optional
Stability Flange
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND IN HOUSING
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND IN HOUSING
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete
Finished grade
Finished grade Optional
Stability Flange
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND IN HOUSING
WIRING DIAGRAM
Integral
Transformer
Fixed Stem And T-Housing Option Fixture Installation
TRANSFORMER HOUSING MUST BE INSTALLED ABOVE GRADE. POWER PIPE™ IS LABELED AT GRADE LEVEL.
TRANSFORMER HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY
  • Page 1 1
  • Page 2 2
  • Page 3 3

B-K lighting Litestick - Style T Installation guide

Brand
B-K lighting
Model
Litestick - Style T
Type
Installation guide

B-K Lighting Litestick - Style T is a low voltage halogen or LED fixture that can be used for in-ground recessed installation. It is suitable for wet locations and comes with an optional stability flange for added stability. The fixture can be used with a remote transformer or an integral transformer. The adjustable stem allows for customization of the height of the fixture, and the optional stability flange helps to keep the fixture in place. The fixture is easy to install and comes with all the necessary hardware.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents