SILENT KNIGHT SD505-TCHB100 Handheld Detector Programmer User manual

Brand
SILENT KNIGHT
Model
SD505-TCHB100 Handheld Detector Programmer
Type
User manual

SILENT KNIGHT SD505-TCHB100 Handheld Detector Programmer is a handheld device designed to program and test compatible smoke and heat sensors. It allows users to set device addresses, read analog sensor values, and troubleshoot potential issues. With its simple button interface and clear display, the programmer streamlines the process of configuring and maintaining fire detection systems. Whether you're a professional installer or a building manager, this tool provides a convenient and efficient way to ensure the proper functioning of your fire safety equipment.

SILENT KNIGHT SD505-TCHB100 Handheld Detector Programmer is a handheld device designed to program and test compatible smoke and heat sensors. It allows users to set device addresses, read analog sensor values, and troubleshoot potential issues. With its simple button interface and clear display, the programmer streamlines the process of configuring and maintaining fire detection systems. Whether you're a professional installer or a building manager, this tool provides a convenient and efficient way to ensure the proper functioning of your fire safety equipment.

GENERAL DESCRIPTION:
Remote Programming Cable
(All Modules except DCP-FRCME-S)
Remote Programming Cable
(DCP-FRCME-S)
Programming Buttons
Display
TCH-B100-NS PROGRAMMER OPERATING INSTRUCTIONS
PROGRAMMING BUTTONS
ADDRESS SETTING:
To Remote
Programming Jack
NOTE: PRIOR TO PROGRAMMING ENSURE BATTERY IS CONNECTED.
Remote Programming
Jack
Power on. Automatically reads the address of a sensor. Subsequent
operations will advance the device address by ten.
Power off. Advances the device address by one.
Stores the displayed addresss to the device and is used to read sensor
analog levels.
Analog Photoelectric Smoke Sensor
Analog Ionization Smoke Sensor
Analog Heat Sensor
DCP Fast Response Contact Module
DCP Fast Response Contact Monitor
DCP Signal Output Module
DCP Dual Relay Module
TCH-B100-NS is designed for use with the following products:
ALG-V/ALG-EA
AIE-EA
ATG-EA
FRCME-S
FRCME-4
SOM
R2M
CZM
1.
2.
3.
4.
Install sensor onto programmer, ensuring that sensor protrusions align with programmer grooves.
Press the left gray button to switch programmed on. A battery check message will appear followed by
the devices address ( un-programmed sensors will read address 127).
Set the required address by incrementing the left and right gray buttons (the display will show three red
flashing dots if the address being programmed is different from the device's current address).
When the desired address is present press the red button to store that address. The three red dots on
the display will no longer be present.
LEFT GRAY BUTTON
RIGHT GRAY BUTTON
RED BUTTON
DCP Conventional Zone Module
DWG # HA-06-082
Page 1 of 2, 05-03
PART # 1700-09906
HOCHIKI AMERICA CORPORATION
7051 Village Drive, Suite 100
Buena Park, CA 90621-2268.
DCP Dual Input Monitor Module
DIMM
DISPLAY MESSAGES:
TESTING A SENSOR
NOTE: Ionization sensors require a 30 seconds stabilization period before analog value reading should be taken.
bAt - On upon power up (battery check). Also on when battery is low. Low battery good for up to
3,000 address setting operation.
E0 - Attempting to set an address beyond 127.
E1 - Attempting to program an address with no device connected.
E2 - Can not find device after power up.
E3 - Invalid sensor response.
E4 - Can not find the device program.
E5 - Device read error.
E6 - Fail during Analog value reading.
DWG # HA-06-082
Page 2 of 2, 05-03
PART # 1700-09906
Install the sensor and power up programmer as previously described on page 1.
Press the "Red" button. An "A" will appear on the display followed by the analog value.
The value will be continuously updated for three minutes.
The "ALG" photoelectric sensor should have a value displayed of between 56-63. The "AIE"
ionization sensor should have a value displayed of bewteen 52-73.
1.
2.
3.
Values out of these ranges indicate that the sensor chamber has become contaminated. Refer to
technical bulletin "HA-96" for proper servicing instructions or return sensor to factory for
servicing.
  • Page 1 1
  • Page 2 2

SILENT KNIGHT SD505-TCHB100 Handheld Detector Programmer User manual

Brand
SILENT KNIGHT
Model
SD505-TCHB100 Handheld Detector Programmer
Type
User manual

SILENT KNIGHT SD505-TCHB100 Handheld Detector Programmer is a handheld device designed to program and test compatible smoke and heat sensors. It allows users to set device addresses, read analog sensor values, and troubleshoot potential issues. With its simple button interface and clear display, the programmer streamlines the process of configuring and maintaining fire detection systems. Whether you're a professional installer or a building manager, this tool provides a convenient and efficient way to ensure the proper functioning of your fire safety equipment.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents