Escea DL1100 Installation guide

Installation / Service Instructions

For the latest documentation, visit www.escea.com

630241_14

DL850 / DL1100

Gas Fireplaces

Important:

The appliance shall be installed in accordance with;

• This installation instruction booklet

• Local gas ﬁtting regulations

• Municipal building codes

• Electrical wiring regulations

• Any other relevant statutory regulations.

• AS/NZS 5601:2010 Gas Installations

WARNING:

This appliance must be installed by a qualiﬁed person.

Do not modify this appliance.

This appliance is not intended for use by young children or inﬁrm persons unless they have been

adequately supervised by a responsible person to ensure that they can use the appliance safely.

Young children should be supervised to ensure that they do not play with the appliance.

Failure to follow these instructions could cause a malfunction of the heater, which could result

in death, serious bodily injury, and/or property damage. Failure to follow these instructions may

also void your ﬁre insurance and/or warranty.

Who can install this product:

Installation must be carried out by a registered installer who, on completion of the installation,

must issue a:

AUS: Certiﬁcate of Compliance

NZ: Certiﬁcates that comply with the latest legislation

in accordance with national and/or local codes. If these are not issued then the Escea warranty

may be void.

Warranty Repair and Annual Servicing:

Please contact Escea if you require warranty work. Warranty repair work must be carried

out by a recognised gas ﬁre technician. It is recommended that recognised Escea Gas Fire

Technicians are also used to carry out annual servicing requirements (particularly during the

warranty period). For contact details of recognised Escea Gas Fire Technicians in your area, or

for replacement parts, please contact the retailer from whom the appliance was purchased our

visit our website.

The heater must be installed according to these instructions and in compliance with all relevant

building, gas ﬁtting, electrical and other statutory regulations (e.g. AS/NZS 5601). Any

shortcomings in the appliance and ﬂue installation will be the responsibility of the installer, and

Escea will not be accountable for any such failings or their consequences.

Manufactured by: Escea Ltd, PO Box 5277 Dunedin NZ, Ph: +64 3 478 8220. For contact

details of your local Escea distributor or dealer in New Zealand, please visit: www.escea.com or

email: [email protected]. From Australia, please visit www.escea.com.au, call AU: 1800 460 832

or WA: 1800 730 140, or email us at [email protected]

DL850 PRODUCT SPECIFICATION

MODEL NAME

DL850

Description of Appliance Gas Fire Heater

Star Rating 5.0 Stars

Max. Heat Output 9.2kW

A/NZ Approval No. AS/NZS 5263.1.3:2016

Gas Type Natural Propane ULPG

Gas input High 38 MJ/hr 38 MJ/hr 33 MJ/hr

Low 17 MJ/hr 15 MJ/hr 14 MJ/hr

Inlet Pressure Max 5 kPa 5 kPa 5 kPa

Min 1.13 kPa 2.75 kPa 2.75 kPa

Operating Pressure on High 1.0 kPa 2.3 kPa 2.6 kPa

Burner Jet Size Front: 2.45mm

Rear: 2.3mm

Front: 1.4mm

Rear: 1.3mm

Front: 1.2mm

Rear: 1.1mm

Burner Aeration Front and Rear:

Small Hole

Front and Rear:

Large Hole

Front and Rear:

Large Hole

Pilot injector Regular Red Red

Appliance Dimensions

(mm)

Width 959mm

Height 560mm

Depth 517 mm

Weight Kg 65 kg

Ignition System Electronic Ignition to pilot system

Escea PCB

Flame Safeguard Flame Rectiﬁcation

Remote controls Yes

Timers Yes

Clock Yes

Function lock / child Yes

Temperature control Yes

Connections Electric 230V AC

Gas 1/2" BSPP female lower centre of ﬁreplace chassis

Flue Type Aluminium Flexi Flue and PolyPro

Flue Size 75mm and 100mm Flexi Flue & PolyPro

Spigot Loca-

tion

Right hand top

Data badge location On Chassis Base

DL1100 PRODUCT SPECIFICATION

MODEL NAME

DL1100

Description of Appliance Gas Fire Heater

Star Rating 5.0 Stars

Max. Heat Output 10.4kW

A/NZ Approval No. AS/NZS 5263.1.3:2016

Gas Type Natural Propane ULPG

Gas input High 43 MJ/hr 43 MJ/hr 39 MJ/hr

Low 19 MJ/hr 15 MJ/hr 15 MJ/hr

Inlet Pressure Max 5 kPa 5 kPa 5 kPa

Min 1.13 kPa 2.75 kPa 2.75 kPa

Operating Pressure on High 1.0 kPa 2.3 kPa 2.3 kPa

Burner Jet Size Front: 2.6mm

Rear: 2.6mm

Front: 1.4mm

Rear: 1.3mm

Front: 1.3mm

Rear: 1.2mm

Burner Aeration Front and Rear:

Small Hole

Front and Rear:

Large Hole

Front and Rear:

Large Hole

Pilot injector Regular Red Red

Appliance Dimensions

(mm)

Width 1259mm

Height 560mm

Depth 517 mm

Weight Kg 80 kg

Ignition System Electronic Ignition to pilot system

Escea PCB

Flame Safeguard Flame Rectiﬁcation

Remote controls Ye s

Timers Yes

Clock Yes

Function lock / child Yes

Temperature control Yes

Connections Electric 230V AC

Gas 1/2" BSPP female lower centre of ﬁreplace chassis

Flue

Type

Aluminium Flexi Flue and PolyPro

Flue

Size

75mm and 100mm Flexi Flue & PolyPro

Spigot

Loca-

tion

Right hand top

Data badge location On Chassis Base

A Installation Process and Product Description 7

A1 Product Description 7

A2 Recommended Installation Process 7

A3 Product Dimensions 8

B Creating the Cavity 9

B1 Cavity Shape 9

B2 Fascia 9

B3 Cavity Base 10

B4 Hearth 10

B5 Wall Linings 11

B6 Mantle Clearance 11

B7 Television Clearances 12

B8 Corner Installations 12

B9 Distance from Fireplace Base to Fascia Base 12

C Installing the Electricity and Gas to the Appliance 13

C1 Power Supply 13

C2 Network Cable 13

C3 Gas Pipe Sizing 14

C4 Gas Pipe Position 14

C5 Gas Isolating Valve 14

C6 Pressure Test Point 14

D Installing the Flue 15

D1 Flue Conﬁguration (If less than 4 m ﬂue length is required) 15

D2 Flue Conﬁguration (If more than 4m ﬂue length is required) 17

D3 Installing the Horizontal Powerﬂue Wall Terminal Option 18

D4 Installing in Accordance with Relevant Codes 19

D5 Creating the Hole in the Outside Wall 20

D6 Installing the Internal Vertical Powerﬂue (UVP) 22

D7 Installing the External Vertical Powerﬂue (UVP) 23

D8 Running the Flue 24

D9 Running the Powerﬂue Electrical Cable 25

E Installing the Appliance 26

E1 Installation 26

E2 Connecting the Network Cable 26

E3 Connecting the Flue 27

E4 Fixing the Appliance to the Base and Wall 27

E5 Fixing Appliance to Base 27

E6 Fixing Appliance to Wall 27

E7 Removing the Glass 28

E8 Converting the Appliance Gas Type 28

E9 Checking the Pilot Ignition 29

E10 Log Fuel Bed Installation 30

E11 River Stone or Coal (Pebbles) Fuel Bed Installation 31

E12 Crystalight Fuel Bed Installation 31

E13 Crystalight and Driftwood Fuel Bed Installation 32

E14 Checking the Operating Pressure 32

E15 Home Automation Setup 33

F Fitting the Fascia and Finishing Installation 35

F1 Fitting the Fascia Panels 35

F2 Fitting the Bevelled Sided Fascia Panels 36

F3 Fitting the Squared Fascia Panels 38

F4 Fitting the Inset Fascia Panels 40

F5 Locating Wall Mount Cradle for Wireless Control 43

F6 Operating the Appliance for the First Time 43

F7 Normal Operating Sounds and Smells: 44

F8 Cleaning the Glass 44

G Installation Checklist 45

S Service Manual 46

S1 Error Codes 46

S2 Serial Number 48

S3 Checking Operating Pressure 48

S4 Cleaning the Log Set, Fascia, and Glass 48

S5 Servicing the Horizontal/Universal Vertical Powerﬂue 49

S6 Removing or Cleaning the Fan 50

S7 Replacing Electronic Drawer 52

S8 Replacing a Wireless Control 52

S9 Annual Service Procedure 53

S10 Wiring Diagram 54

B

ACDEFGSERVICE

7

A

Installation Process and Product Description

A1 Product Description

The Escea DL series gas ﬁre is a room sealed gas appliance designed to be built into a cavity. These

appliances are ﬂued using collinear ﬂexible aluminium ﬂue (with PolyPro ﬂue extensions in some instal-

lations) connected to a powerﬂue.

The user will control their ﬁre with the Radio Frequency (RF) remote that will normally be left in its

wall mount cradle. In addition to the RF remote the appliance has a single auxiliary On/O button on

the unit. When not in operation it is in a standby mode unless it is physically isolated from the mains

supply.

A2 Recommended Installation Process

The following diagram illustrates the steps required to install your gas ﬁre.

The sequence in which you choose to do these tasks will vary depending on your individual

scenario. Please read these instructions fully before proceeding with the installation.

Leave the installation of the fascia panels until the very end of the installation and

commissioning to avoid damage to the fascia panels.

Create the Cavity Install electrical / gas

connections and ue

system

Install appliance and

nish cavity

Finish installation,

t fascia and test

appliance

Section B Section C, D Section E Section F

Important: Installations that are not speciﬁcally outlined in this manual

should be referred to the Escea Architectural Advisory Team.

Please email [email protected]

To ensure that your installation is fully complete, please use the “Installation Checklist” on page

52.

B

A C D E F G SERVICE

8

A3 Product Dimensions

Not to be mistaken for cavity dimensions.

B

ACDEFGSERVICE

9

B

Creating the Cavity

B1 Cavity Shape

The DL850/DL1100 is suitable for both timber framed and masonry cavities.

The cavity shape is dependant on two things:

-The ﬂue conﬁguration (section D1 on page 15)

-The fascia (section B2 on page 9)

B2 Fascia

The cavity shape is dependent on the fascia type. There are three fascia types available with the

DL850 and DL1100:

Bevelled

Inset

Squared

The Bevelled and Squared fascias sit proud of the ﬁnished wall surface and have a simple cavity

shape. The cavity may be constructed from combustible materials.

The Inset fascia sits ﬂush with, or inset from, the ﬁnished wall surface and has a more complex

cavity shape. The cavity framing and wall facing for a minimum of 300mm directly above the

Inset fascia must be constructed from non-combustible materials.

Please check the style of fascia before commencing the building of the cavity to the dimensions

shown below. The cavity for Bevelled and Squared fascias may be constructed from combustible

timber framing materials.

NOTE: It is not necessary to line the sides, top, or back of the cavity.

Cavity for Inset Fascia

Cavity for Bevelled or

Squared Fascia

B

A C D E F G SERVICE

10

Ideal Cavity Dimensions (mm):

DL850: A B (min) B (max) C (min) D E (min) E (max)

Bevelled /

Squared

965 560 575 565 - - -

Inset 965 585 590 565 995 30 130

DL1100:

Bevelled /

Squared

1265 560 575 565 - - -

Inset 1265 585 590 565 1295 30 130

NOTE: The ﬁnal cavity size and shape should account for the ﬂue direction as shown on following

page.

775 565

Downward

Flue

Vertical or

side Flue

B3 Cavity Base

This appliance MUST be fully supported on its base. The base must extend over the entire area

of the underside of the appliance. The base must also be levelled to prevent vibration from

possible fan imbalance. The base of the cavity must be strong enough to support the total

product weight, which is approximately 65kg (DL850) and 80kg (DL1100), depending on fuel

bed.

B4 Hearth

The base of the appliance must be installed a minimum of 100mm o the ﬂoor, unless the

appliance is being installed at ﬂoor level in which case a hearth is required, made from non-

combustible material, which must extend no less than 300mm from the front of the ﬁre.

This hearth should be at least as wide as the ﬁre’s outer fascia and no less than 10mm thick.

Raised hearths can be any size but must also be constructed from non-combustible materials.

The ﬂoor in front of this hearth will still get warm so if the ﬂoor covering is vinyl, nylon carpet

or another heat sensitive material then we recommend extending the hearth to 450mm from

the ﬁre. A raised hearth can be of any size but must be constructed from non-combustible

materials.

SQUARED FASCIA ONLY: The fascia must not be installed ush against a hearth as the

replace draws air from the lower surface of the fascia. As such the fascia must be raised a

minimum of 25mm from a hearth. For fascia measurements, see section B9 on page 12.

B

ACDEFGSERVICE

11

NOTE: If the hearth is to be covered with tiles or some other veneer then the ﬁre must be installed so

that the base of the appliance is level with the ﬁnished top surface of the hearth.

B5 Wall Linings

The front mounting ﬂanges of the appliance must be on

top of the ﬁnished wall surface in order for the fascia

panels to mount properly. Take into account any plaster

board, tiles, or any other ﬁnishing surface that may be

intended for the ﬁnished wall surface. Wall ﬁnishing

materials must not encroach upon the minimum cavity

clearances given in section B2 on page 9.

The wall board that lines the outside of this opening can

be normal dry wall (plaster board) and does not need to be

non-combustible.

NOTE: The temperature of the wall lining directly above

the heater does get warm and hence may discolour paint

ﬁnishes that are susceptible to temperature damage or distort

vinyl wall coverings. For durability of ﬁnishes and surfaces

you should contact the relevant manufacturer for their

speciﬁcation.

The cavity framing and wall facing for a minimum of 300mm directly above the Inset fascia must

be constructed from non-combustible materials.

For more detail on cavity construction, view the “Drawings for Architects” in the technical section

of the Escea website.

B6 Mantle Clearance

Please refer to the diagram to the right. Mantles or protruding ledges mounted above the heater

that are made from combustible materials, must

not extend outside of the dimensions shown.

Except for Inset fascias, maintain a 30mm

clearance around the fascia to ensure ease of

fascia removal.

NOTE: No clearance is needed underneath Inset

Fascias.

TOP DOWN VIEW

Cavity

Framework

Plasterboard

FIREPLACE

Wall Finish

Cavity

Framework

Plasterboard

Wall Finish

FIREPLACE

Bevelled/Squared

Inset

min

min max

ma

x

B

A C D E F G SERVICE

12

B7 Television Clearances

The following are the recommended minimum

clearances for the location of any electrical

equipment (such as Plasma TV, LCD TV, or

home theatre) above an Escea DL Series gas

ﬁre. Use either a shelf or mantle below your

TV screen or, alternatively, you can construct

a recess to mount your TV screen into.

NOTE: The above television clearance

recommendations are to be treated as a

suggestion of a suitable installation only. It

is the responsibility of the end user to check

the installation instructions of their electrical

appliances to ensure that the location in relation

to the gas ﬁre is suitable. Escea in no way guarantees or takes responsibility that the above installation

suggestion will be suitable for all electrical or home entertainment appliances.

B8 Corner Installations

If a cavity is to be created in a corner, the following drawing

gives the minimum sized interior wall dimensions.

Minimum corner install dimensions (mm):

DL850 DL1100

A 970 1145

B 960 1260

C 510 510

B9 Distance from Fireplace Base to Fascia Base

The following side-on views show the measurement from the base of the ﬁreplace to the base of

the Fascia.

FIRE

BASE

18mm

BEVELLED

FASCIA

FIRE

BASE

0mm

INSET

FASCIA

FIRE

BASE

5mm

FASCIA

SQUARED

45º

C

B

A

END OF SECTION B

By the end of this section, you should have:

□ A framed, but un-lined, cavity sized to suit your fascia and ue conguration

□ Provision for sucient access to the powerue for future servicing

B

ACDEFGSERVICE

13

C

Installing the Electricity and Gas to the Appliance

C1 Power Supply

While the cavity is being created, consideration must be given to the location of an

appropriate power supply. An earthed 230/240 volt mains power connection (typically a

standard 3 pin outlet) must be available within 1m of the bottom right of the appliance. This

connection must be accessible after the heater has been fully installed so that the appliance

can be safely disconnected from the mains

power supply prior to servicing.

A mains isolation switch (compliant to

AS:NZS 5601 Clause 6.2.8) which is

accessible from outside the cavity can also

be used to disconnect the power.

Regardless of the method used, it MUST

ALWAYS be possible to safely isolate the

electrical supply to the appliance after it has

been fully installed.

This appliance must not be located

immediately below a socket outlet. This appliance will draw a maximum of 2 Amps from a

230/240V supply. No additional power supply is required for the power ﬂue.

An electrical wiring diagram is located underneath the electronic tray, and also in the rear of this

manual (section S10 on page 54).

C2 Network Cable

If the appliance is to be wired to a home automation system or internet router/network is being

installed then provision must be made for the network cable to get to the control tray. A plastic

plug is provided on the rear left of the appliance for a network cable to pass through the chassis

and reach the control tray. Allow enough slack in the network cable to ensure the electronic

tray can still be removed from the appliance. See section E2 on page 26 for ﬁnal connection

of the network cable.

Network cable

positions

Appliance

Mains Cord

B

A C D E F G SERVICE

14

C3 Gas Pipe Sizing

Gas pipe should be sized as per the requirements of AS/NZS 5601. The pipe sizing must be

sucient to deliver the following volume of gas to the heater with all other gas appliances in the

home running at the same time:

DL850 Gas Consumption = 38MJ/hr

DL1100 Gas Consumption = 42MJ/hr

C4 Gas Pipe Position

The DL850 / DL1100 have two possible entry points for gas pipe: on the rear right corner and

the front right. Each is sealed by either a plastic grommet or plastic plug. If you wish to use the

rear exit location, you may swap the grommet and plug positions.

The gas connection on the appliance is a ½” female BSP at the very front right of the appliance.

This section of the piping will need to be ﬂexible to allow for pipe disconnection and ﬁrebox

removal.

C5 Gas Isolating Valve

It is recommended that a gas isolating valve be installed as close to the regulator on the gas inlet

side as possible with easy access if the fascia is removed. This will allow for easier servicing in the

future.

C6 Pressure Test Point

As per AS/NZS 5601, a pressure test point shall be provided by the installer prior to the inlet of

the appliance

Gas pipe entry positions

Regulator

Inlet gas connection

(Grommet)

(Plug)

Installer to swap plug and

grommet if required

END OF SECTION C

By the end of this section, you should have:

□ An unlined cavity with a standard three pin 230/240V AC supply that the appliance can

be plugged into

□ An electrical isolating switch that is accessible once the appliance is installed

□ A suitably sized gas supply to the right hand side of the appliance with a pressure test

point, ready to be connected once installed

□ Network cable installed, ready for plugging into appliance (if being connected to internet

router/network)

B

ACDEFGSERVICE

15

D

Installing the Flue

D1 Flue Conﬁguration (If less than 4 m ﬂue length is required)

If your ﬂue system is less than 4m long (as shown in diagrams below), then a simple aluminium

ﬂexible ﬂue is required. If you wish to install a longer ﬂue run, up to 12m, see section D2 on page

17.

When deciding on the placement of the ﬂue fan, mitigation of sound transmission may be

required with short installations or when installing in certain materials.

Horizontally Terminated: Utilises the Escea horizontal power ﬂue enclosure kit.

The horizontal oset of the terminal can be any amount up to the total ﬂue length listed below.

Please consult with Escea’s technical sta if your intended ﬂue conﬁguration steps outside of

the bounds of the ﬂue conﬁgurations shown below.

Note: When ﬂueing above the ﬁre, the pipe must slope towards ﬁre - NOT towards the terminal. Also

when ﬂueing below the ﬁre, the pipe must slope towards the terminal - NOT towards the ﬁre.

X

Y

X + Y Maximum = 4m

Y Maximum = 1.5m

Y Minimum = 0m

X Maximum = 4m

X Minimum = 0m

X + Y Minimum = 0.4m

X

Y

X + Y Maximum = 4m

Y Maximum = 4m

Y Minimum = 0m

X Maximum = 4m

X Minimum = 0m

X + Y Minimum = 0.4m

B

A C D E F G SERVICE

16

Vertically Terminated: Utilises the Escea vertical power ﬂue enclosure kit.

400mm Min.

4m Max.

Overall flue length:

X

Y

UVP Fan Unit

1.2m F-F Liner

UVP Cowl

X Max = 4m

Y Max = 4m

X + Y Max = 4m

B

ACDEFGSERVICE

17

D2 Flue Conﬁguration (If more than 4m ﬂue length is required)

If your ﬂue system is greater than 4m long (as shown in diagrams below), then a ﬂexible ﬂue

with condensate trap and rigid PolyPro tube ﬂue lengths is required.

For further information and

detail on PolyPro (Rigid) ﬂue

and condensate traps, see the

documentation supplied with the

ﬂue components.

4m

Ø75mm / Ø100mm

Flexible Flue

1.2m Co-axial Flue

Vertical Powerue

12m MAX

Ø100mm

Condensate Trap

Ø80mm / Ø100mm

PP Tube

4m

ESCEA WALL

TERMINAL

12m MAX

Ø80mm / Ø100mm

PP Tube

Ø100mm

Condensate Trap

Ø75mm / Ø100mm

Flexible Flue

12m MAX

4m

Ø100mm

Condensate Trap

Ø75mm / Ø100mm

Flexible Flue

Ø80mm / Ø100mm

PP Tube

ESCEA WALL

TERMINAL

4m

12m MAX

UVP Fan Unit

1.2m F-F Liner

UVP Cowl

Ø75mm / Ø100mm

Flexible Flue

Ø100mm

Condensate Trap

Ø80mm / Ø100mm

PP Tube

B

A C D E F G SERVICE

18

D3 Installing the Horizontal Powerﬂue Wall Terminal Option

The horizontal powerﬂue wall terminal must be

installed in the correct orientation (the small

horizontal slot should be at the bottom). This

allows for the correct operation of the ﬂue

system and prevents the ingress of water.

The horizontal powerﬂue wall terminal must

be weathertight when installation is complete

to prevent damage to the dwelling. It must be

installed by a suitably qualiﬁed person.

Fit the horizontal powerﬂue wall terminal

into the hole and ﬁx in place, making sure

the installation is sealed appropriately to

prevent the ingress of water from outside the

wall cladding. Take notice of the label on the

termination which shows the correct orientation of the terminal.

Note: It is the responsibility of the installer to ensure the horizontal powerﬂue wall terminal is installed

to all relevant building codes to ensure weather tightness.

B

ACDEFGSERVICE

19

D4 Installing in Accordance with Relevant Codes

The location of the horizontal powerﬂue wall terminal must be installed in accordance with AS/NZS

5601 and any other relevant building codes. If possible, avoid installing the horizontal powerﬂue wall

terminal in areas exposed to high winds and extreme weather.

Some of the minimum clearances for a fan assisted wall terminal are listed below; please refer to

AS/NZS 5601 Gas installation standard for full guidance on the design of the ﬂue system. Where

possible allow a greater clearance.

A Below eaves, balconies and other projections 200mm

B From the oor, above a balcony or other surface 300mm

C From a return wall or external corner 300mm

D From a gas meter or regulator vent 1000mm

E From electricity meter or fuse box 500mm

F From a drain pipe or soil stack 75mm

G Horizontally from any building structure or obstruction 500mm

H From any other ue terminal or combustion air intake 300mm

J Horizontally from any openable window, door, non-mechanical air inlet, or any other

opening into a building with the exception of sub oor ventilation

300mm

K From a mechanical air inlet or spa blower 1000mm

L Vertically below any openable window, door, non-mechanical air inlet, or any other

opening into a building with the exception of sub oor ventilation

300mm

N Horizontally from a roof light 600mm

O Vertically from a roof light 500mm

Q Vertically from a flat roof 500mm

R Horizontally from a vertical structure 500mm

S Below a roof window 2000mm

T Above or either side of a roof window 600mm

U From a dormer window 1500mm

V Above the apex of the roof (see note 1 on following page) 300mm

W From an open flue 1500mm

N

R

F

S

W

U

A

V

K

Q

E

J

A

H

E

D

C

A

O

G

J

L

B

M

P

Prohibited area for ues is

below or Distance 'E' to

the left and right of the

Electricity meter

or fuse box

M = Gas Meter

P = Electricity meter or Fuse box

H

B

A C D E F G SERVICE

20

NOTES:

1) Should the ﬂue not extend past the apex of the roof, the bottom opening of the ﬂue should

extend at least 200mm from the roof (or 300mm in regions with heavy snow).

2) The installation of a ﬂue into a carport is not recommended.

3) The ﬂue terminal will get very hot when in use. Precautions should be taken to protect people and

animals from injury.

D5 Creating the Hole in the Outside Wall

When cutting the hole in the outside wall, be mindful of how the

installation horizontal powerﬂue wall terminal will be ﬁnished; the

installation must be weatherproof.

Ideal hole/cavity size for Horizontal Powerﬂue

Without Side Brackets With Side Brackets

X 298mm 360mm

Y 298mm 298mm

Z 175mm Excluding allowance for ﬂue which exits here

The horizontal powerﬂue wall terminal can be attached to the wall in two ways:

A) From the front of the terminal:

B) By attaching the optional wall terminal installation brackets to the sides of the cavity and

attaching the horizontal powerﬂue wall terminal to these, from the front:

Attach the Ø100mm and Ø75mm ﬂexible aluminium ﬂues to the spigots on the rear of the

horizontal powerﬂue wall terminal using the hose band clamps supplied. Plug the powerﬂue

electrical cable into the back of the horizontal powerﬂue wall terminal.

For information on the PolyPro ﬂue, see the installation manual which is supplied with the ﬂue

components.

Ensure that the electrical cable is ﬁrmly secured to the wall terminal or building to prevent

damage or disconnection if pulled.

Page is loading ...

Escea DL1100 Installation guide

This manual is also suitable for

Escea DL1100 Installation guide

Related papers

Other documents