BIXOLON SPP-R220 Mobile Printer User manual

Category
Print & Scan
Type
User manual
User's Manual
SPP-R220
MOBILE PRINTER
Rev. 1.02
http://www.bixolon.com
Rev. 1.02
- 2 -
SPP-R220
Table of Contents
Manual Information & Usage Precautions ························································ 3
1. Content Confirmation ··················································································· 10
2. Product Part Names ····················································································· 11
3. Installation & Usage ····················································································· 12
3-1 Battery Installation ··············································································· 12
3-2 Battery Charging ·················································································· 12
3-2-1 Using Battery Charger ····································································· 12
3-2-2 Using Single Battery Cradle (Optional) ················································ 13
3-2-3 Using Vehicle Charger (Optional) ······················································· 13
3-2-4 Using Single Docking Cradle (Optional) ·············································· 14
3-2-5 Using Quad Battery Charger / Quad Docking Cradle (Optional) ··············· 14
3-3 Paper Installation ················································································· 16
3-4 Using Belt Clip ····················································································· 17
3-5 Using Belt Strap (Optional) ···································································· 18
3-6 Using Case (Optional) ··········································································· 19
3-7 Using Control Panel ············································································· 20
3-8 Using MSR ························································································· 21
3-9 Recommended Papers ········································································· 21
4. Self-Test ····································································································· 22
5. Label Printing Function ················································································ 25
5-1 Label Function Setting ·········································································· 25
5-2 Auto Calibration Function ······································································ 25
6. Peripherals Connection ················································································ 26
6-1 Bluetooth & Wireless LAN Connection ····················································· 26
6-2 Interface Cable Connection ···································································· 27
7. Printer Cleaning ·························································································· 28
8. Appendix ···································································································· 29
8-1 Specifications ······················································································ 29
8-2 Certification ························································································ 31
8-3 Label Types ························································································ 32
Rev. 1.02
- 3 -
SPP-R220
Manual Information
Manual Information & Usage Precautions
This user’s manual contains basic information for product usage as well as for emergency
measures that may be required.
The following separate manuals provide more detailed content on various technological
issues and areas.
1. Software Manual
2. Bluetooth & Wireless Manual
3. Commands Manual
4. Code Pages Manual
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and
quality of all our products. In following, product specifications and/or user manual content
may be changed without prior notice.
Rev. 1.02
- 4 -
SPP-R220
Safety Precautions
In using the present appliance, please keep the following safety regulations in order to
prevent any hazard or material damage.
WARNING
Violating following instructions can cause serious injury or death.
Do not bend the cable by force or leave it under any
heavy object.
A damaged cable can cause a fire.
Do not plug in or unplug with your hands wet.
You can be electrocuted.
Keep the plastic bag out of children’s reach.
If not, a child may put the bag on his head.
Do not pull the cable to unplug.
This can damage the cable, which is the origin of a fire or a
breakdown of the printer.
You must use only the supplied adapter.
It is dangerous to use other adapters.
Do not plug several products in one multi-outlet.
This can provoke over-heating and a fire.
If the plug is wet or dirty, dry or wipe it before usage.
If the plug does not fit perfectly with the outlet, do not plug in.
Be sure to use only standardized multi-outlets.
PROHIBIT
ED
PROHIBIT
ED
PROHIBIT
ED
PROHIBIT
ED
PROHIBIT
ED
ONLY SUPPLIED ADAPTER
PROHIBIT
ED
Rev. 1.02
- 5 -
SPP-R220
CAUTION
Violating following instructions can cause slight wound or damage the appliance
.
Do not use the printer when it is out of order. This
can cause a fire or an electrocution.
Switch off and unplug the printer before calling your dealer.
Do not let water or other foreign objects in the
printer.
If this happened, switch off and unplug the printer before
calling your dealer.
Use only approved accessories and do not try to
disassemble, repair or remodel it for yourself.
Call your dealer when you need these services.
Do not touch the blade of auto cutter.
Install the printer on the stable surface.
If the printer falls down, it can be broken and you can hurt
yourself.
Keep the desiccant out of children’s reach.
If not, they may eat it.
If you observe a strange smoke, odor or noise from
the printer, unplug it before taking following
measures.
Switch off the printer and unplug the set from the mains.
After the disappearance of the smoke, call your dealer to
repair it.
TO UNPLUG
PROHIBIT
ED
DISASSEMBLING
PROHIBITED
PROHIBIT
ED
PROHIBIT
ED
TO UNPLUG
PRINTER
PRINTER
PRINTER
PRINTER
DEALER
PRINTER
Rev. 1.02
- 6 -
SPP-R220
Battery Safety Precautions
Make sure to review the user manual carefully prior to product use.
Neglecting to heed the following instructions can result in battery overheating, combustion,
explosion, damage and/or decline in performance and product life.
Danger
1. Do not allow water, seawater or moisture to enter or leak into the battery. If the safety
mechanism within the battery becomes oxidized, the battery may overcharge with
abnormal electrical current and/or voltage so that it may overheat, ignite and/or explode.
2. Do not place the battery near open flames or heating devices, such as stoves.
Exposure to excessive heat may cause damage to the resin case and/or insulating
materials, thus causing a short circuit within the battery that may result in battery
overheating, combustion, and/or explosion.
3. Charge the battery only with the exclusive charger specified (optionally provided) by
BIXOLON. The use of an incorrect charger may result in overheating, combustion
and/or explosion of the battery.
4. Charging the battery with a modified charger may result in overheating, combustion
and/or explosion of the battery by abnormal chemical reaction caused by incorrect
polarity.
5. Do not directly connect the battery to an electrical power outlet not specified by
BIXOLON or an automobile’s cigarette lighter jack. Doing so may result in overheating,
combustion and/or explosion of the battery by over-current and/or over-voltage.
6. Do not heat the battery or place it near a fire. Doing so may melt insulation materials,
damage the safety mechanism/equipment, and/or ignite the electrolytic solution. There
is a potential risk of battery overheating, combustion, and/or explosion.
7. Do not reverse the connection of (+) and (-) electrodes of the battery. Charging the
battery in reverse polarity may produce an undesired chemical reaction inside the
battery cell, causing unexpected behavior during discharging such as overheating,
explosion, or fire.
8. Do not allow the battery’s (+) or (-) pole to come into contact with any metal. In addition,
do not carry or store the battery with metallic items, such as necklaces and hairpins.
Doing so may cause a short circuit of the battery generating an over-current. There is
the potential risk to overheat, ignite and/or explode the battery or overheat the metallic
items, such as necklaces, hair pins etc.
9. Do not throw the battery or subject it to strong shock. If the safety mechanism in the
battery is damaged, the battery may be overcharged and, consequently, an adverse
chemical reaction may be generated in the battery. There is a potential risk of battery
overheating, combustion, and/or explosion.
Rev. 1.02
- 7 -
SPP-R220
10. Do not pierce the battery with a pointed object, such as nail or awl, or strike with a
heavy object, such as a hammer, and take care not to step on the battery. There is a
potential risk of battery overheating, combustion, and/or explosion caused by an
internal short circuit.
11. Do not solder the battery directly. Doing so may melt the insulating materials and/or
damage the safety mechanism or safety equipment, resulting in battery overheating,
combustion, and/or explosion.
12. Do not disassemble and/or modify the battery. The battery contains safety equipment
and a safety mechanism to prevent danger. There is a potential risk of overheating,
combustion, and/or explosion caused by disassembly.
13. Do not charge the battery near open flames and/or under direct sunlight. Because
exposure to high temperatures triggers the operation of the safety mechanism, the
battery may not charge or may overcharge due to destruction of the safety mechanism.
There is a potential risk of overheating, combustion, and/or explosion.
14. Do not expose the battery to high temperatures over 60 oC, and do not use or store it
in a hot or humid place.
15. Do not use the battery if it is damaged or the exterior is deformed due to external
shock or if it is swollen.
Warning
1. Do not place the battery within the reach of small children to prevent any swallowing
accidents. If a small child has swallowed the battery, consult a physician immediately.
2. Do not place the battery in a microwave oven and/or high voltage appliance. Doing so
can cause rapid overheating and/or destruction of the sealing, resulting in battery
overheating, combustion, and/or explosion.
3. Do not combine and use any battery of different capacity and/or type with the primary
battery. Doing so can cause excessive electrical discharge during use or excessive
charging during charging, resulting in an abnormal chemical reaction within the battery
that can cause battery overheating, combustion, and/or explosion.
4. If during battery usage, storage, or charging, a strange odor or conditions differing from
the normal, such as overheating, color changes, warping, etc., are detected, remove
the battery from the product or charger and discontinue use. Continued use may
cause battery overheating, combustion, and/or explosion.
5. When recharging, if the battery is not charged after the normal fixed charging time,
discontinue charging. Continued charging can result in battery overheating,
combustion, and/or explosion.
6. If the battery appears to be coated with condensation or emits a strange odor,
immediately place it far away from any heat source. The condensation may be
caused by a leak of electrolytic solution that can ignite to cause battery combustion
and/or explosion.
7. If the battery is leaking electrolytic solution and any of the solution enters the eyes,
immediately wash out with clean water, and then consult a physician to receive
treatment. Neglecting to do so can cause permanent eye injuries.
Rev. 1.02
- 8 -
SPP-R220
Caution
1. Do not use or leave the battery in a location exposed to high temperatures or intense
direct sunlight, such as within an automobile. Doing so can cause battery overheating
and/or combustion. In addition, battery performance and product life may be reduced.
2. The battery contains a safety mechanism to prevent danger. Do not use the battery in
a location that is prone to static electricity (above the amount covered by the
manufacturer’s product warranty) that can cause damage to this safety mechanism.
Damage to the safety mechanism can result in battery overheating, combustion, and/or
explosion.
3. The temperature ranges for battery usage are as follows. Any usage outside of these
ranges can result in battery overheating and/or damage. In addition, battery performa
nce and product life may be reduced.
- Charging: 0 ~ 40 oC
- Product Usage: -20 ~ 60 oC
- Storage: -20 ~ 60 oC (30 days)
- Long-Term Storage: -20 ~ 40 oC (90 days)
4. Please review the exclusive charger manual carefully for charging instructions.
5. If you observe any abnormal symptom, such as strange smell and overheating, on first
use after purchasing the product, contact your local dealer immediately.
6. If a child must use the battery, the child’s parent or legal guardian should clearly explain
the instructions from the user manual prior to use. In addition, the parent or legal
guardian should periodically confirm that usage is being conducted in accordance with
user manual instruction during use.
7. Store the battery in a location that is out of the reach of small children. During usage,
make sure to also place the charger and/or product out of the reach of small children.
8. If the battery is leaking electrolytic solution, and the solution comes in contact with the
skin or clothing, immediately wash thoroughly with clean water. Contact with skin can
result in skin disorders.
9. Make sure to review the user manual and precautions carefully prior to use.
In addition, after carefully reviewing the user manual and precautions, place them in a
secure location for future reference when needed.
10. There is a risk of explosion when replacing with an incorrect battery. Only exchange it
for another one of the same or equivalent model specified by BIXOLON. Insulate the
used battery by attaching insulation tape to its port, and then dispose of the battery
according to local regulations.
11. If using the printed side of preprinted paper, this may cause malfunction.
Rev. 1.02
- 9 -
SPP-R220
Recommended
1. Review the user manual for instructions concerning insertion/removal of batteries
into/from the product.
2. The battery shipped with the product is partially charged, and it is good for checking the
operation of the equipment. Charge the battery first with the supplied charger if the
equipment does not work or long hours of operation are required.
3. To avoid improper use of the battery, review the product user manual carefully.
4. Do not charge the battery for long times in excess of the normal charging time indicated
in the user manual.
5. If the battery is not to be used for a long period of time, remove it from the product and
store in a location with low humidity. If the battery is stored while still inserted in the
product in a highly humid location, oxidization may occur along with a decline in battery
performance.
6. Turn off the power after using the equipment. Otherwise the performance of the battery
will be degraded over time.
7. The battery may fail to charge if it is not used for a long period of time. Charge the
battery with the supplied charger at least once every six months if the equipment is not
used for a long time. Leaving the battery for a long time without charging may degrade
the performance of the battery or cause system trouble.
8. If the battery terminal is contaminated, clean the contact with a dry cloth before using it.
Using the battery with contaminated contacts may cause problems when supplying
power to the equipment or charging due to irregular electric contact.
9. Each battery has a life cycle. If the usage time of the produce is shortened, replace with
a new battery. Insulate the used battery by attaching insulation tape to its port, and
then dispose of the battery according to local regulations.
Other Precautions
The copyright for this user manual and various other manuals is property of the BIXOLON
Co., Ltd. Any copying or conversion into electronic firm and saving of this material
without the express written permission of BIXOLON Co., Ltd. is strictly prohibited.
Use of the information contained in this manual is not subject to any patent liability. This
manual has been prepared with utmost care and attention to detail but may contain certain
errors and/or omissions.
BIXOLON Co., Ltd. is not legally liable for any damages resulting from the use of the
information in this manual.
BIXOLON Co., Ltd. and its affiliates are not legally liable for any damages, loss, costs,
and/or expenses that result from the breakdown, malfunction, and/or misuse of the product
due to violation or neglect of the operation and maintenance information and instructions
provided by the BIXOLON Co., Ltd., as well as from the unauthorized alteration, repair,
and/or modification of the product by the user and/or third party.
BIXOLON Co., Ltd. is not legally liable for any damages and/or issues resulting from the
use of options and/or parts that are not authentic BIXOLON products or authorized
products.
Rev. 1.02
- 10 -
SPP-R220
1. Content Confirmation
The following items should all be contained in the printer package.
Contact the dealer from which the purchase was made if any item is damaged and/or
missing.
Basic items
SPP-R220
Battery Pack
Battery Charger
Paper
Power Cord
Belt Clip
CD
Manual Quick
Optional items
Belt Strap
Vehicle Charger
Interface Cable
Single Battery
Cradle
Shoulder Strap
Case
Cleaning Pen
Battery Pack_V2
(with outer contacts)
Single Docking
Cradle
Quad Docking Cradle
Quad Battery Charger
Wall Mount
(RWM-350)
(for Quad
Battery Charger)
Rev. 1.02
- 11 -
SPP-R220
2. Product Part Names
Front
Rear
Paper Cover
Power Button
Open button
Paper Feed Button
Cable Connection
Power Connection
Battery
Hole for mounting belt strap / belt clip
Interface Cap
Rev. 1.02
- 12 -
SPP-R220
3. Installation & Usage
3-1 Battery Installation
1) Insert the battery on the rear side of the
printer, aligning the battery hook properly.
2) Push the battery into the slot until a
snapping sound is heard.
NOTE
As the battery is not charged at the time of
purchase, charge the battery prior to product
use. (Use the battery charger)
3-2 Battery Charging
3-2-1 Using Battery Charger
1) Turn off the printer power.
2) Connect the power cord to the battery
charger , and then connect AC power.
3) Open the external interface cap in the
direction of .
4) Connect the battery charger to the power
connector.
CAUTION
The printer may incur serious damage if the
battery charger provided by BIXOLON is not
used. BIXOLON is not legally liable for any
such damages. (The voltage and electrical
current specifications of the printer and
battery charger must match.)
WARNING
Turn off the power before charging the battery
for the printer.
Rev. 1.02
- 13 -
SPP-R220
3-2-2 Using Single Battery Cradle (Optional)
1) Connect the power cord to the battery
charger .
2) Connect the battery charger to the
power connector of the single battery
cradle .
3) Plug the power cord into an electrical
outlet.
4) Insert the battery into the single
battery cradle until a snapping sound
is heard.
3-2-3 Using Vehicle Charger (Optional)
1) Turn off the power to the printer.
2) Connect the vehicle charger to your
car’s cigarette lighter jack.
3) Open the external interface protection
cap in the direction of .
4) Connect the vehicle charger to the power
connector.
CAUTION
The printer may be seriously damaged if a
battery charger not provided by BIXOLON
is used. BIXOLON is not liable for such
damage.
WARNING
Turn off the power before charging the
battery for the printer.
Rev. 1.02
- 14 -
SPP-R220
3-2-4 Using Single Docking Cradle (Optional)
1) Turn the printer off.
2) Slide the printer in the single docking
cradle as shown in the picture.
3) Push the printer in until a clicking sound
is heard.
4) Charging will begin when the printer is
installed.
5) Pull out the printer to separate it.
CAUTION
Please be sure to use the battery with
external power contacts.
3-2-5 Using Quad Battery Charger / Quad Docking Cradle (Optional)
3-2-5-1 Connecting the cables
1) Connect the power cord to the adaptor,
and Connect the adaptor to the power
connector of the quad battery charger /
quad docking cradle.
2) Plug the power cord into a power Outlet.
Input power is 100 ~ 240VAC, 50/60Hz,
1.0A.
3) When the power is supplied, the yellow,
green and red lamps are on for three
seconds and do the self-test.
WARNING
Use only designated AC/DC adaptor.
(12VDC, 3A)
Rev. 1.02
- 15 -
SPP-R220
3-2-5-2 Charging Battery (Printer)
1) Fasten batteries via the battery hooks
into the quad battery charger as
shown above.
2) Push the battery in until a snapping
sound is emitted.
3) Charging begins as soon as the
battery is completely inserted.
(Batteries are charged to 8.4VDC, 0.8A.)
4) Push the hook and pull up to extract
the battery.
1) Turn the printer off.
2) Slide the printer in the quad docking
cradle as shown in the picture.
3) Push the printer in until a clicking
sound is heard.
4) Charging will begin when the printer is
installed.
5) When charging complete, Pull out the
printer to separate it.
CAUTION
Please be sure to use the battery with
external power contacts.
NOTE
Battery charging status descriptions are as follows.
Lamp
Charge Status
Charge Time
Red Lamp On
Charging
2.5 hours
Green Lamp Blinking
Over 80% Charged
Green Lamp On
Fully Charged
Red Lamp Blinking
Error Replace
or Reinstall Battery
CAUTION
1. If the red lamp of the charger blinks, install the battery again.
2. If the red lamp continues to blink despite several attempts (4 ~ 5 times) to
install the battery, contact your local dealer.
3. The charging time may vary depending on the type of the charger or ambient temperature.
Rev. 1.02
- 16 -
SPP-R220
3-3 Paper Installation
1) Press the Open button to open the paper
cover.
2) Insert the paper as shown in the image.
(Remove any remaining core of a fully
used paper roll.)
3) Take care to align the paper correctly.
4) Pull the paper out as shown in the image
and close the paper cover.
5) Tear off any excess paper in the direction
of the side of the printer.
Rev. 1.02
- 17 -
SPP-R220
3-4 Using Belt Clip
1) Insert the screw of the belt clip to the belt
clip mounting hole.
2) Fasten the screw of the belt clip with an
object like a coin as shown in the picture.
(Be careful to fasten in the correct
direction.)
3) Insert the clip to the belt.
Belt Clip
Coin
Belt
Rev. 1.02
- 18 -
SPP-R220
3-5 Using Belt Strap (Optional)
1) Insert the belt strap screw into the belt
strap hole.
2) Use a coin to tighten the belt strap screw
as shown in the image.
3) Undo the belt strap Velcro.
4) Fasten the belt strap to a belt.
5) Close the Velcro as shown in the image.
Belt
Belt Strap
Coin
Belt
Rev. 1.02
- 19 -
SPP-R220
3-6 Using Case (Optional)
1) Open its top cover.
2) Insert the printer in the case in the
direction shown in the picture.
3) Close the Velcro.
4) Attach it to the belt using the clip on the
back of the case.
Note
The clip of the protective case can be rotated in
two steps of 30° for each step (up to 60°)
Belt
Rev. 1.02
- 20 -
SPP-R220
3-7 Using Control Panel
Power Button
This button is used to turn the printer on and off.
1) When the printer is off, press this button for approximately 2
seconds to turn on the power.
2) When the printer is on, press this button for approximately 2
seconds to turn off the power.
Paper Feed Button
To feed paper manually, press this button.
In addition, self-testing and Hexadecimal Dumping can be done.
1) Refer to “4. Self-Test” for self-test information.
2) Refer to the service manual regarding Hexadecimal Dumping.
Battery Status LED (Blue or Red)
1) If the blue LED is lit, the battery is fully charged.
2) If the blue LED is blinked, the battery is half charged.
3) If the red LED is blinked, the battery must be charged
or replaced.
Error LED (Left-sided)
1) If the red LED is lit, the paper cover is open.
2) If the red LED is blinking, either the paper has been fully used or
the print head is overheated.
(Replace the roll of paper or turn off the printer for at least 10
minutes.)
3) If the red LED continues to blink, it may indicate a more serious
problem with the product. Call your authorized service dealer.
Bluetooth & Wireless LAN LED (Right LED)
1) When using Bluetooth
If the printer is ready for wireless communication with any
Bluetooth, the green LED as well as the battery status LED is
turned on.
2) When using wireless LAN
The right indicator shows the signal strength from wireless LAN.
The green LED blinks for acceptable signal strength while the
green LED blinks for weak signal strength.
In power save mode, only the Status LED is lit.
NOTE
The power saving mode is activated after the first communication, with the
default time interval being 10 seconds.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

BIXOLON SPP-R220 Mobile Printer User manual

Category
Print & Scan
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages