Eldat RCD14 Operating instructions

Brand: Eldat

Model: RCD14

Type: Operating instructions

Eldat RCD14 is a versatile radio control receiver designed for various low-voltage applications. It offers three distinct operating modes, enabling flexible control options. With a frequency of 868.30 MHz and FSK modulation, it ensures reliable wireless communication. The receiver features four open collector outputs, allowing you to control multiple devices or functions simultaneously. It supports up to 32 transmitter codes, providing ample capacity for controlling multiple transmitters.

Disposal

Waste electrical products and batteries not be

disposed of with household waste!

Dispose of the waste product via a collec-

tion point for electronic scrap or via your

specialist dealer.

Put the packaging material into the recy-

cling bins for cardboard, paper and plas-

tics.

Warranty

Within the statutory warranty period we undertake

to rectify free of charge by repair or replacement

any product defects arising from material or pro-

duction faults.

Any unauthorized tampering with, or modications

to, the product shall render this warranty null and

void.

Conformity

Hereby, ELDAT EaS GmbH declares that the ra-

dio equipment type RCD14 is in compliance with

Directive 2014/53/EU. The full text of the EU dec-

laration of conformity is available at the following

internet address: www.eldat.de

Service

If, despite correct handling, faults or malfunctions

occur or if the product was damaged, please

contact your retailer or the manufacturer.

ELDAT EaS GmbH

Schmiedestraße 2

15745 Wildau

Germany

Phone: + 49 (0) 33 75 / 90 37-310

Fax: + 49 (0) 33 75 / 90 37-90

Internet: www.eldat.de

E-Mail: [email protected]

RCD14 Open Collector Receiver

UM181409_0523 DE/EN

Deleting Specic Codes

In the “Specic delete” mode you can delete spe-

cic transmitter codes.

1. Press the programming button P for more

than 1.6 sec. The delete mode is acti-vated.

The LED ashes rapidly.

2. Press the transmitter button to be deleted.

As soon as the LED of the radio control lights

up for ap-prox. 4 sec., the transmission code

has been deleted

By briey pressing the programming button

P, you can abort the delete procedure.

Deleting Codes Completely (Reset)

In “Reset” mode you can delete all the memo-

rized codes.

1. Press the programming button P for more

than 1.6 sec. The delete mode is activated.

The LED ashes rapidly.

2. Press the programming button P again for

more than 1.6 sec. As soon as the LED lights

up for approx. 4 sec., all the memorized codes

have been deleted

By briey pressing the programming button

P, you can abort the delete procedure.

Connection diagram

5-24

GND

156234

Models

RCD14E5004A01 5-24 V DC with pin header

RCD14E5004A02 5-24 V DC w/o pin header

Technical Details

Frequency: 868,30 MHz

Modulation: FSK

Coding:

Operating mode BA1

Easywave A/B Output OC1

Easywave C/D Output OC3

Operating mode BA2 and BA3

Easywave A Output OC1

Easywave B Output OC2

Easywave C Output OC3

Easywave D Output OC4

Power supply: 5 V-24 V DC

Current consumption: 11 mA

Output load:

Umax 40 V

Imax 80 mA

Operating temperature: -20 °C to +60 °C

Dimensions:

RCD14 ... A01: 35x31 mm + 6 mm pin

length, RM2,54

RCD14 ... A02: 35x31 mm, RM2,54

Wiring example

RCD14

6 OC1

5 GND

4 Vin 5-24V

3 OC2

2 OC3

1 OC4

Programming-

button P

Intended Use

This unit may only be used as a radio control sys-

tem for low-voltage applications!

The manufacturer shall not be liable for any da-

mage caused by improper or non-intended use!

Safety Advice

Carefully read through these in-struc-

tions before connecting and operating

the unit!

- Have malfunctioning devices checked by the

manufacturer!

- Do not make any unauthorized alterations or

modications to the unit!

Select operating mode

For programming (see “Memorizing the Transmis-

sion Codes” there are 3 programming modes for

the 3 operating modes (OM) of the receiver.

These operating modes are displayed by dierent

LED ashing patterns.

Operating Mode LED Flashing

OM1 ON/OFF

(2 button operation)

OC1 = ON/OFF (A/B)

OC3 = ON/OFF (C/D)

OM2 ON/OFF Toggeln

(1 button operation)

and

DEAD MAN

(button pressed > 1,6s)

OC1=A, OC2=B,

OC3=C, OC4=D

OM3 DEAD MAN

(max 36 sec)

OC1=A, OC2=B,

OC3=C, OC4=D

Change the operating mode by briey (< 1.6 sec)

pressing the programming button:

Operating mode -> OM1 -> OM2 -> OM3 ->

Operating mode

Memorizing the Transmission Codes

In the “Memorizing the Transmission Codes”

mode you can transfer the codes of your transmit-

ter to the receiver.

Note: Generally you only have to transfer the

code of one button per transmitter. The code of

the opposite transmitter buttons will be assigned

automatically.

1. Briey (< 1.6 sec.) press the programmin but-

ton P. Programming mode 1 is activated. The

LED ashes. If necessary change the opera-

ting mode (see “Select operating mode“).

2. Press and hold a transmitter channel button.

As soon as the code has been memorized,

the LED lights up for 4 sec. and then ashes

again. Release the transmitter button.

3. Repeat step 2 with the other transmitters if

needed. You can memorize up to 32 transmit-

ter codes into the receiver.

4. Briey (< 1.6 sec.) press the programming

button P to return to the operating mode.

In case of longer power failure the program-

ming of the receiver remains.

LED

Antenna

Eldat RCD14 Operating instructions

Eldat RCD14 Operating instructions

Eldat RCD14 Operating instructions

Related papers

Other documents