Cooper Lighting VS Series User manual

Brand: Cooper Lighting

Model: VS Series

Category: Motorcycle Accessories

Type: User manual

IMPORTANT: Dual voltage and multi-tap ballasts are factory wired for 277 Volt input. Before installation make certain power supply and ballast voltages are

compatible. For use with other line voltages, remove wire nut splicing the black lead from the quick disconnect plug and 277V lead from ballast. Cap off

lead with wirenut. Splice black lead from the quick disconnect plug with the desired voltage lead from ballast.

APPLICATIONS:

• 70W HID and 42W CFL fixtures are not suitable for operation in ambients exceeding 40°C. 100W HID

fixtures are not suitable for operation in ambients exceeding 25°C.

• Minimum supply wire conductor requirements 90°C in J-box. 150°C supply wire is required for through

wire applications.

• Thread sealing compound (not provided) must be applied to all unused plugs when

used in wet location applications.

• Caulking (not provided) must be used between ceiling and upper cover when used

in wet location applications.

TO ENSURE PROPER GROUNDING AND POLARITY:

• Connect the fixture ground wire (Green) to the supply ground.

• Connect the fixture neutral wire (White) to the supply neutral.

• Connect the fixture line wire (Black) to the supply line.

NOTE: If you are unsure which wires are ground, neutral or line, consult an electrician.

TOOLS REQUIRED:

• Phillips screw driver

• Slotted screw driver

• 1/8” Allen wrench

INSTALLATION INSTRUCTIONS:

1) Loosen Allen set screw and remove guard and globe.

2) Loosen (3) #12 Phillips pan head screws and remove lower ousing assembly.

Disconnect plug and receptacle.

3) Knockout desired holes in upper cover. Make electrical splices, push leads into J-Box

and install upper cover to ceiling or J-Box using appropriate fasteners (not provided).

4) Reconnect plug and receptacle and reassemble lower housing to upper cover.

5) Install lamp and reinstall globe and guard.

NOTE: For Metal Halide application, a glass globe or lens must be used unless an open rated lamp is installed.

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

General: Upon receipt of fixture thoroughly inspect for any

freight damage, which should be brought to the attention of the

delivery carrier. Compare the catalog description listed on the

packing slip with the fixture label on the housing to be sure the

correct merchandise has been received.

Safety: This fixture must be wired in accordance with

the National Electrical Code, National Electrical Safety Code

and applicable local codes and ordinances. Proper grounding is

required to insure personal safety. Carefully observe grounding

procedure under installation section. This fixture is not suitable

for Hazardous or Classified Locations.

VS SERIES VAPORTIGHT

CEILING MOUNT

PAGE 1 OF 2

11/1/06 IMI-661

LUMARK 1121 HIGHWAY 74 SOUTH PEACHTREE CITY, GEORGIA 30269 11/1/06 IMI-661 ADH061573

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest Cooper Lighting representative.

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

Risk of Electric Shock. Disconnect power at fuse or circuit breaker panel or fuse box

before installing or servicing.

Risk of Burn. Allow fixture to cool before changing bulb or handling fixture.

J-Box

(Not Provided)

Upper Cover

Quick Disconnect

Receptacle

Quick Disconnect

Plug

(4) #10 Fasteners

(Not Provided)

Lower Housing

(3) #12 Philips

Pan Head Screw

Loosen Set Screw with

1/8” Allen Wrench to

Remove Guard

Ceiling

Apply Caulking between

Ceiling and Fixture when used

in Wet Location Applications

(12) Ø.210 KO

(5.33)

Ø2.75

(69.8)

Ø3.50

(88.9)

Ø4.75

(120.6)

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

General: Upon receipt of fixture thoroughly inspect for any

freight damage, which should be brought to the attention of the

delivery carrier. Compare the catalog description listed on the

packing slip with the fixture label on the housing to be sure the

correct merchandise has been received.

Safety: This fixture must be wired in accordance with

the National Electrical Code, National Electrical Safety Code

and applicable local codes and ordinances. Proper grounding is

required to insure personal safety. Carefully observe grounding

procedure under installation section. This fixture is not suitable

for Hazardous or Classified Locations.

VS SERIES VAPORTIGHT

PENDANT MOUNT

PAGE 2 OF 2

11/1/06 IMI-661

LUMARK 1121 HIGHWAY 74 SOUTH PEACHTREE CITY, GEORGIA 30269 11/1/06 IMI-661 ADH061573

IMPORTANT: Dual voltage and multi-tap ballasts are factory wired for 277 Volt input. Before installation make certain power supply and ballast voltages are

compatible. For use with other line voltages, remove wire nut splicing the black lead from the quick disconnect plug and 277V lead from ballast. Cap off

lead with wirenut. Splice black lead from the quick disconnect plug with the desired voltage lead from ballast.

APPLICATIONS:

• 70W HID and 42W CFL fixtures are not suitable for operation in ambients exceeding 40°C.

100W HID fixtures are not suitable for operation in ambients exceeding 25°C.

• Minimum supply wire conductor requirements 150°C.

• Thread sealing compound (not provided) must be applied to all unused plugs when

used in wet location applications.

TO ENSURE PROPER GROUNDING AND POLARITY:

• Connect the fixture ground wire (Green) to the supply ground.

• Connect the fixture neutral wire (White) to the supply neutral.

• Connect the fixture line wire (Black) to the supply line.

NOTE: If you are unsure which wires are ground, neutral or line, consult an electrician.

TOOLS REQUIRED:

• Phillips screw driver

• Slotted screw driver

• 1/8” Allen wrench

• 5/64” Allen wrench

INSTALLATION INSTRUCTIONS:

1) Loosen Allen set screw and remove guard and globe.

2) Loosen (3) #12 Phillips pan head screws and remove lower ousing assembly.

Disconnect plug and receptacle.

3) Pull supply leads into upper cover and thread upper cover to pendant. To avoid pinched wires,

only 6” of supply leads should extend into fixture. Use wire ties to bundle wires. Splice supply

leads to quick disconnect leads.

Note: See instructions in section “TO INSURE PROPER GROUNDING AND POLARITY”.

4) Reconnect plug and receptacle and reassemble lower

housing to upper cover.

5) Install lamp and reinstall globe and guard.

NOTE: For Metal Halide application, a glass globe or lens must be

used unless an open rated lamp is installed.

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

Risk of Electric Shock. Disconnect power at fuse or circuit breaker panel or fuse box

before installing or servicing.

Risk of Burn. Allow fixture to cool before changing bulb or handling fixture.

Upper Cover

3/14-14 Threaded

Pendant

Quick Disconnect

Receptacle

Quick Disconnect

Plug

(3) #12 Philips

Pan Head Screw

Lower Housing

Loosen Set Screw with

1/8” Allen Wrench to

Remove Guard

Tighten Set Screw with

5/64” Allen Wrench

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest Cooper Lighting representative.