Intermec 5055 Data Collection PC Recovery Instructions

Intermec
Brand
Intermec
Model
5055 Data Collection PC
Type
Recovery Instructions

This manual is also suitable for

Recovery Instructions
P/N 962-054-032
Revision A
December 2000
5055 Data Collection PC
P/N 962-054-032 Revision A
*962054032*
2 5055 Data Collection PC Recovery Instructions
"
NOTE: These instructions are tied to the 5055 Toolkit V3.0: Windows NT P/N: 235-027-001
Windows 95 P/N: 235-028-001
The 5055 Toolkit V3.0 CDĆROM is used to restore the main partition and recovery partition
on a 5055 Data Collection PC.
The UPDATE.BAT batch file displays menus and does most of the recovery process. This
file can also be located in an \Update" server folder, shared between the 5055 PC and the
server. For example, C:\5055base\Update" is the directory structure that runs the
RUNME.BAT file off the CDĆROM.
"
NOTE: If the 5055 PC does not have a recovery partition, see the “5055 Data Collection PC Technical
Reference” P/N: 978-054-002 for legacy update instructions.
Server (Personal Computer)
The server must have the following before Windows 95 or NT 4.0 can be restored on the
5055 PC: a 10BaseĆT connection to a NetBEUI Network, any version of Windows 95, 98,
NT 4.0, or 2000, and enabled file/print sharing.
The RUNME.BAT file from the toolkit CDĆROM creates a Recovery Partition" within a
folder on the server. This folder can be customized to suit specific needs.
1. Insert this CDĆROM in a computer connected to the network and share its CDĆROM
drive with the name: CDROM.
2. From the Windows desktop, select Start → Run, type D:\runme.bat, then click OK
to run the installation wizard. D:\ is the CDĆROM drive in this example.
See the 5055 PC Technical Reference" for instructions to enable file/print sharing (Windows
95), share the CDĆROM drive, or install the contents of the Toolkit CDĆROM.
Client (5055 PC)
The client 5055 PC must have SystemSoft BIOS version 1.21 or later, a 10BaseĆT connecĆ
tion to a NetBEUI Network, and an attached PS/2 keyboard before doing this recovery.
3. Reboot the 5055 PC, wait for the following prompt after the system memory tests,
then simultaneously press <Ctrl>, <Alt>, [R] to enter the recovery partition.
<CTRL–ALT–S> to enter the System Configuration Utility
4. If the following menu appears, go to the Original Recovery Partition" section.
[1] Restore Normal Operation
[2] Boot to DOS Network
5. If the following menu appears, go to the New Recovery Partition" section.
1. NetBEUI Recovery
2. TCP/IP Recovery
3. Boot to DOS Network
5055 Data Collection PC Recovery Instructions 3
Original Recovery Partition
Do the following to update the recovery partition to the latest files:
1. Press [2] to select Boot to DOS Network, then press <Enter>.
2. Check the server's network share name and the network cable connections. Change
to the folder that has the NET.EXE file, type Net Use Q: \\SERVER\CDROM, then
press <Enter>. SERVER" is the computer in which the CDĆROM is installed.
3. Type Q: CD\UPDATE, then type update.bat and press <Enter> to display the
Main Menu." See the README.TXT file on the 5055 Toolkit CDĆROM for explanaĆ
tions of the menu options.
4. Press [2] to select Administration Options, then press [3] to select Update
Recovery Partition. At the warning prompt, press [Y] to continue.
5. Reboot the 5055 PC, wait for the following prompt after the system memory tests,
then simultaneously press <Ctrl>, <Alt>, [R] to enter the recovery partition, then go
to the New Recovery Partition" section.
<CTRL–ALT–S> to enter the System Configuration Utility
New Recovery Partition
Do the following to restore the main partition. See the 5055 Technical Reference for addiĆ
tional Administrative Options" menu information.
1. Press [1] if NetBEUI is used for network connections or [2] if TCP/IP is used, then
press <Enter>. At each prompt, enter the applicable information or wait 10 seconds
for the default information.
"
NOTE: If TCP/IP Recovery is elected, the default gateway (defaultgateway0), the subnet mask (subnet-
mask0), and the ip address (ipaddress0) are to be entered. Use spaces between digits instead of
periods. For example: type “225 255 255 0” instead of “255.255.255.0” for the default gateway.
2. Enter the network share name with the UPDATE.BAT file. If a custom"
UPDATE.BAT file is saved on a server, enter its shared path. The shared location of
the 5055 Toolkit CD can also be entered, for example: \\SERVER\CDROM
3. Press [1] from the UPDATE.BAT menu to restore the main partition from a PQI file.
This requires PowerQuest EasyRestore (PQER).
4. Note that the folder must be shared. Enter the path to the PQI image to be restored,
for example: \\SERVER\FOLDERNAME
If the PQI image is on the CDĆROM, then type: \\MYPC\CDROM.
If a custom PQI file is located in an Images" folder on the PC, then type:
\\MYPC\IMAGES.
5. Type the name of the PQI file to be restored. If this file is in a folder below the shared
folder, type the path. For example, if the root of the CDĆROM drive is shared and the
NT_V30.PQI file is in the Images" folder, then type: IMAGES\NT_V30.PQI
"
NOTE: The default PQI file names will change for each version of the released toolkits. For example:
NT_V31.PQI or W95_V31.PQI.
4 5055 Data Collection PC Recovery Instructions
Intermec Technologies Corporation
550 Second Street SE
Cedar Rapids, IA 52401
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Intermec 5055 Data Collection PC Recovery Instructions

Intermec
Brand
Intermec
Model
5055 Data Collection PC
Type
Recovery Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents