H3C S5130-30C-HI Installation guide

H3C S5130-HI Switch Series

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6W106-20190409

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this

document are the property of their respective owners.

Notice

The information in this document is subject to change without notice. All contents in this document, including

statements, information, and recommendations, are believed to be accurate, but they are presented without

warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions

contained herein.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage, use,

and disposal of this product must meet the applicable national laws and regulations.

Preface

H3C S5130-HI Switch Series Installation Guide describes the procedures for installing, accessing,

and troubleshooting the H3C S5130-HI Switch Series.

This preface includes the following topics about the documentation:

• Audience.

• Conventions.

• Documentation feedback.

Audience

This documentation is intended for:

• Network planners.

• Field technical support and servicing engineers.

• Network administrators working with the S5130-HI switch series.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Description

Boldface Bold

text represents commands and keywords that you enter literally as shown.

Italic

Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars,

from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&) sign

can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in Boldface. For

example, the

New User

window opens; click

OK

.

>

Multi-level menus are separated by angle brackets. For example,

File

>

Create

>

Folder

.

Symbols

Convention Description

WARNING!

An alert that calls attention to important information that if not understood or followed

can result in personal injury.

CAUTION:

An alert that calls attention to important information that if not understood or followed

can result in data loss, data corruption, or damage to hardware or software.

IMPORTANT:

An alert that calls attention to essential information.

NOTE:

An alert that contains additional or supplementary information.

TIP:

An alert that provides helpful information.

Network topology icons

Convention Description

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that

supports Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access

controller engine on a unified wired-WLAN switch.

Represents an access point.

Represents a wireless terminator unit.

Represents a wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security

gateway, or load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL

VPN, IPS, or ACG module.

Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots,

and other information in the examples differ from what you have on your device.

T



Documentation feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

i

Contents

Preparing for installation ···································································· 1

Safety recommendations ············································································································· 1

Examining the installation site ······································································································· 1

Temperature/humidity ·········································································································· 2

Cleanliness ························································································································ 2

EMI ·································································································································· 2

Laser safety ······················································································································· 3

Installation tools ························································································································· 3

Installing the switch ·········································································· 4

Installing the switch in a 19-inch rack ····························································································· 6

Installation methods ············································································································· 6

Installation accessories ········································································································· 7

Rack-mounting by using front mounting brackets ······································································· 9

Rack-mounting by using front and rear mounting brackets ························································· 11

Rack-mounting by using front mounting brackets and mounting rail assemblies ······························ 14

Mounting the switch on a workbench ···························································································· 17

Grounding the switch ················································································································ 17

Grounding the switch with a grounding strip ············································································ 17

Grounding the switch with a grounding conductor buried in the earth ground ·································· 19

Installing/removing a fan tray ······································································································ 20

Installing a fan tray ············································································································ 20

Removing a fan tray ··········································································································· 21

Installing/removing a power module ····························································································· 22

Installing a PSR150 power module ························································································ 22

Removing a PSR150 power module ······················································································ 23

Installing a PSR360-56A/PSR720-56A/PSR1110-56A power module ··········································· 24

Removing a PSR360-56A/PSR720-56A/PSR1110-56A power module·········································· 26

Connecting the power cord ········································································································ 27

Connecting the AC power cord for the fixed AC power module ···················································· 27

Connecting a DC power cord for the fixed DC power module ······················································ 28

Connecting the AC power cord for a PSR150-A1 power module ·················································· 29

Connecting the DC power cord for a PSR150-D1 power module ················································· 30

Connecting the AC power cord for a PSR360-56A, PSR720-56A, or PSR1110-56A power module ····· 31

Installing/removing an expansion card ·························································································· 31

Installing an expansion card ································································································ 32

Removing an expansion card ······························································································· 34

Verifying the installation ············································································································· 34

Accessing the switch for the first time ················································· 35

Setting up the configuration environment ······················································································ 35

Connecting the console cable ····································································································· 35

Connecting the Mini USB console cable ························································································ 36

Setting terminal parameters ······································································································· 38

Powering on the switch ············································································································· 38

Setting up an IRF fabric ··································································· 40

IRF fabric setup flowchart ·········································································································· 40

Planning IRF fabric setup ··········································································································· 41

Planning IRF fabric size and the installation site ······································································· 41

Identifying the master switch and planning IRF member IDs ······················································· 41

Planning IRF topology and connections·················································································· 41

Identifying physical IRF ports on the member switches ······························································ 42

Planning the cabling scheme ······························································································· 43

Configuring basic IRF settings ···································································································· 45

Connecting the physical IRF ports ······························································································· 45

Verifying the IRF fabric setup ······································································································ 46

ii

Maintenance and troubleshooting ······················································ 47

Power module failure ················································································································ 47

Fixed power module failure ·································································································· 47

Hot swappable power module failure ····················································································· 48

Fan failure ······························································································································ 49

Fixed fan failure ················································································································ 49

Hot swappable fan tray failure ······························································································ 49

Configuration terminal display problems ························································································ 49

No display ························································································································ 49

Garbled display ················································································································· 50

Appendix A Chassis views and technical specifications ·························· 51

Chassis views ························································································································· 51

S5130-30S-HI ··················································································································· 51

S5130-54S-HI ··················································································································· 52

S5130-30F-HI ··················································································································· 53

S5130-30C-HI ·················································································································· 54

S5130-30C-PWR-HI ·········································································································· 55

S5130-34C-HI ·················································································································· 56

S5130-54C-HI ·················································································································· 57

S5130-54C-PWR-HI ·········································································································· 58

S5130-54QS-HI ················································································································ 59

Technical specifications ············································································································· 60

Appendix B FRUs and compatibility matrixes ······································· 65

FRUs and compatibility matrixes ································································································· 65

Hot swappable power modules ··································································································· 66

Hot swappable fan trays ············································································································ 66

Hot swappable expansion cards ·································································································· 67

Connecting cables to the copper ports on the interface cards ······················································ 67

Appendix C Ports and LEDs ····························································· 69

Ports ····································································································································· 69

Console port ····················································································································· 69

Management Ethernet port ·································································································· 69

USB port ························································································································· 69

10/100/1000BASE-T autosensing Ethernet port ······································································· 70

1/10BASE-T autosensing Ethernet port ·················································································· 70

100/1000Base-X SFP port ··································································································· 70

SFP+ port ························································································································ 71

QSFP+ port ······················································································································ 75

Combo interface ················································································································ 75

LEDs ····································································································································· 76

System status LED ············································································································ 76

Power module status LED ··································································································· 76

RPS status LED ················································································································ 76

Port mode LED ················································································································· 77

10/100/1000BASE-T autosensing Ethernet port LED ································································ 77

100/1000Base-X SFP port LED ···························································································· 78

SFP+ port LED ················································································································· 78

QSFP+ port LED ··············································································································· 78

Management Ethernet port LEDs ·························································································· 79

Expansion card status LED ································································································· 79

Port status LED on the expansion card ·················································································· 80

Input status LED and output status LED on the power module ···················································· 80

Fan tray status LED on the fan tray ······················································································· 80

Appendix D Cooling system ······························································ 81

1

Preparing for installation

H3C S5130-HI Switch Series includes the following models:

• S5130-30S-HI

• S5130-54S-HI

• S5130-30F-HI

• S5130-30C-HI

• S5130-30C-PWR-HI

• S5130-34C-HI

• S5130-54C-HI

• S5130-54C-PWR-HI

• S5130-54QS-HI

Safety recommendations

To avoid any equipment damage or bodily injury caused by improper use, read the following safety

recommendations before installation. Note that the recommendations do not cover every possible

hazardous condition.

• Before cleaning the switch, remove all power cords from the switch. Do not clean the switch

with a wet cloth or liquid.

• Do not place the switch near water or in a damp environment. Prevent water or moisture from

entering the switch chassis.

• Do not place the switch on an unstable case or desk. The switch might be severely damaged in

case of a fall.

• Ensure good ventilation of the equipment room and keep the air inlet and outlet vents of the

switch free of obstruction.

• Connect the yellow-green protection grounding cable before power-on.

• Make sure the operating voltage is in the required range.

• To avoid electrical shocks, do not open the chassis while the switch is operating or when the

switch is just powered off.

• When replacing field replaceable units (FRUs), including expansion cards, power modules, and

fan trays, wear an ESD wrist strap to avoid damaging the units.

Examining the installation site

The switch must be used indoors. You can mount your switch in a rack or on a workbench, but make

sure:

• Adequate clearance is reserved at the air inlet and outlet vents for ventilation.

• The rack or workbench has a good ventilation system.

• Identify the hot aisle and cold aisle at the installation site, and make sure ambient air flows into

the switch from the cold aisle and exhausts to the hot aisle.

• Identify the airflow designs of neighboring devices, and prevent hot air flowing out of the

neighboring device from entering the device.

• The rack is sturdy enough to support the switch and its accessories.

• The rack or workbench is reliably grounded.

2

To ensure correct operation and long service life of your switch, install it in an environment that meets

the requirements described in the following subsections.

Temperature/humidity

Maintain temperature and humidity in the equipment room as described in "Appendix A Chassis

views and technical specifications."

• Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical

property change of materials, and metal corrosion.

• Lasting low relative humidity can cause washer contraction and ESD and bring problems

including loose mounting screws and circuit failure.

• High temperature can accelerate the aging of insulation materials and significantly lower the

reliability and lifespan of the switch.

For the temperature and humidity requirements of different switch models, see "Technical

specifications."

Cleanliness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of

metal components and contact points, especially when indoor relative humidity is low. In the worst

case, electrostatic adsorption can cause communication failure.

Table 1 Dust concentration limit in the equipment room

Substance Concentration limit (particles/m³)

Dust

≤ 3 x 10

4

(no visible dust on the tabletop over three days)

NOTE:

Dust diameter ≥ 5 μm

The equipment room must also meet strict limits on salts, acids, and sulfides to eliminate corrosion

and premature aging of components, as shown in Tabl e 2.

Table 2

Harmful gas limits in the equipment room

Gas Maximum concentration (mg/m

3

)

SO

2

0.2

H

2

S 0.006

NH

3

0.05

Cl

2

0.01

EMI

All electromagnetic interference (EMI) sources, from outside or inside of the switch and application

system, adversely affect the switch in the following ways:

• A conduction pattern of capacitance coupling.

• Inductance coupling.

• Electromagnetic wave radiation.

• Common impedance (including the grounding system) coupling.

3

To prevent EMI, use the following guidelines:

• If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)

to filter interference from the power grid.

• Keep the switch far away from radio transmitting stations, radar stations, and high-frequency

devices.

• Use electromagnetic shielding, for example, shielded interface cables, when necessary.

• To prevent signal ports from getting damaged by overvoltage or overcurrent caused by lightning

strikes, route interface cables only indoors.

Laser safety

WARNING!

The switch is Class 1 laser device. Do not stare into any fiber port when the switch has power. The

laser light emitted from the optical fiber might hurt your eyes.

Installation tools

• Flat-blade screwdriver

• Phillips screwdriver

• ESD wrist strap

All these installation tools are user supplied.

4

Installing the switch

CAUTION:

Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open

the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any consequence.

5

Figure 1 Hardware installation flow

Ground the switch

Install the switch

Start

Connect power cords

Verify the installation

Power on the switch

Select and install power

modules

Hot-swap power

modules?

Yes

No

Operating correctly?

Power off the switch

Troubleshoot the switch

No

Yes

Hot-swap cards?

Install expansion cards

Yes

Troubleshoot the switch

Yes

No

End

No

Hot-swap

fan trays?

Select and install fan trays

Yes

No

Operating correctly?

Install transceiver modules

and cables

6

Installing the switch in a 19-inch rack

Installation methods

Table 3 Installation methods for the S5130-HI switches

Chassis

Installation

methods

Installation requirements

Installation

procedure

S5130-30S-HI

S5130-54S-HI

S5130-30F-HI

S5130-30C-HI

S5130-34C-HI

S5130-54C-HI

Using front

mounting

brackets

Install the front mounting brackets at the port side or

power module side.

See

"Rack-mountin

g b

y using

front mounting

brackets."

S5130-30C-PW

R-HI

S5130-54C-PW

R-HI

Using front

and rear

mounting

brackets

• Install the front mounting brackets at the port

side or power module side.

• Install the rear mounting brackets according to

the rack depth.

{ If the rack depth is in the range of 429 to 595

mm (16.89 to 23.43 in), orient the bracket

with the wide flange inside the rack.

{ If the rack depth is in the range of 274 to 440

mm (10.79 to 17.32 in) and the distance from

the rear rack posts to the inner surface of the

cabinet door is longer than 153 mm (6.02 in),

orient the bracket with the wide flange

outside the rack.

See

"Rack-mountin

g by using

front and rear

mounting

brackets."

S5130-54QS-HI

Using front

mounting

brackets

Install the front mounting brackets at the power

module side.

See

"Rack-mountin

g b

y using

front mounting

brackets."

Using front

and rear

mounting

brackets

• Install the front mounting brackets at the port

side or power module side.

• Install the rear mounting brackets according to

the rack depth.

{ If the rack depth is in the range of 332 to 496

mm (13.07 to 19.53 in), orient the bracket

with the wide flange inside the rack.

{ If the rack depth is in the range of 174 to 341

mm (6.85 to 13.43 in) and the distance from

the rear rack posts to the inner surface of the

cabinet door is longer than 153 mm (6.02 in),

orient the bracket with the wide flange

outside the rack.

As a best practice, use this method for enterprise

networks.

See

"Rack-mountin

g b

y using

front and rear

mounting

brackets."

Using front

mounting

brackets and

mounting rail

assemblies

Install the front mounting brackets at the port side or

power module side.

The distance between the front rack post and the rear

rack post must be in the range of 562 to 754 mm

(22.13 to 29.69 in).

As a best practice, use this method for data centers.

See

"Rack-mountin

g b

y using

front mounting

brackets and

mounting rail

assemblies."

7

Figure 2 Rack-mounting procedure (1)

Figure 3 Rack-mounting procedure (2)

Figure 4 Rack-mounting procedure (3)

NOTE:

If a rack shelf is available, you can put the switch on the rack shelf, slide the switch to an appropriate

location, and attach the switch to the rack by using the mounting brackets.

Installation accessories

Table 4 Installation accessories for the S5130-HI switches

Installation

accessories

S5130-30S-HI

S5130-54S-HI

S5130-30F-HI

S5130-30C-HI

S5130-34C-HI

S5130-54C-HI

S5130-30C-PWR-HI

S5130-54C-PWR-HI

S5130-54QS-HI

Front mounting

brackets (Figure 5)

Provid

ed Provided Provided

Rear mounting

brackets and

shoulder screws

(Figure 6)

N/A Provid

ed Provided

Chassis rails and

slide rails (Figure 7)

N/A N/A

Optional

Grounding cable Provided Provided Provided

8

Figure 5 Front mounting bracket

(1) Hole for attaching the bracket to a rack (2) Hole for attaching the bracket to the switch chassis

Figure 6 Rear mounting bracket and shoulder screw

(1) Hole for attaching the bracket to a rack (2) Shoulder screw

Figure 7 Rack mounting rail kit

(1) Chassis rail (2) Slide rail

9

Rack-mounting by using front mounting brackets

This task requires two people.

This mounting method is applicable only to the S5130-30S-HI, S5130-54S-HI, S5130-30F-HI,

S5130-30C-HI, S5130-34C-HI, S5130-54C-HI, and S5130-54QS-HI switches.

To install the switch in a 19-inch rack by using the front mounting brackets:

1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.

2. Determine the mounting position on the switch for the front mounting brackets.

You can install the front mounting brackets at one of the following positions:

{ S5130-30S-HI, S5130-54S-HI, S5130-30F-HI, S5130-30C-HI, S5130-34C-HI, and

S5130-54C-HI switches—Port side or power module side installation position.

{ S5130-54QS-HI switch—Power module side installation position.

3. Attach the front mounting brackets to the chassis:

a. Unpack the front mounting brackets and the M4 screws (supplied with the switch) for

attaching the brackets to the switch chassis.

b. Align the round holes in the wide flange of one front mounting bracket with the screw holes

in the chassis.

c. Use M4 screws to attach the mounting bracket to the chassis.

d. Repeat the proceeding two steps to attach the other mounting bracket to the chassis.

Figure 8 Attaching the front mounting bracket to the port side

Figure 9 Attaching the front mounting bracket to the power module side

10

4. Mount the chassis in the rack:

a. Install cage nuts (user-supplied) in the mounting holes in the front rack posts. Make sure the

corresponding cage nuts on the left and right front rack posts are at the same height.

b. One person holds the switch chassis and aligns the installation holes on the mounting

brackets with the cage nuts on the rack posts.

c. The other person uses M6 screws (user supplied) to attach the mounting brackets to the

rack.

Figure 10 Mounting the switch in the rack (front mounting brackets at the port side)

Figure 11 Mounting the switch in the rack (front mounting brackets at the power module

side)

11

Rack-mounting by using front and rear mounting brackets

This mounting method is applicable only to the S5130-30C-PWR-HI, S5130-54C-PWR-HI, and

S5130-54QS-HI switches. You can install the front mounting brackets at the port-side or power-side

mounting position as needed. The following takes port-side mounting as an example. The

power-side mounting is similar.

This task requires two people.

To install the switch in a 19-inch rack by using the front and rear mounting brackets:

1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.

2. Attach the front mounting brackets and shoulder screws to the chassis:

a. Unpack the front mounting brackets and the M4 screws for attaching the brackets to the

switch chassis.

b. Align the round holes in the wide flange of one front mounting bracket with the screw holes

in the port-side mounting position on one side of the chassis (see Figure 12 and Figure 13).

c. Use M4 scre

ws (supplied with the switch) to attach the mounting bracket to the chassis.

d. Repeat the proceeding two steps to attach the other mounting bracket to the chassis.

e. Unpack the shoulder screws. Attach the shoulder screw to one of the two installation

positions as red-marked in Figure 12 an

d Figure 13.

Figure 12 Attaching the front mounting brackets and shoulder screws to the chassis

(S5130-30C-PWR-HI/S5130-54C-PWR-HI)

Figure 13 Attaching the front mounting brackets and shoulder screws to the chassis

(S5130-54QS-HI)

12

3. Attach the rear mounting brackets to the rack:

a. Determine to orient the rear mounting brackets with the wide flange inside or outside the

rack.

b. Install cage nuts (user-supplied) in the mounting holes in the rear rack posts. Make sure the

corresponding cage nuts on the left and right rear rack posts are at the same height.

c. Attach the rear mounting brackets to the rear posts with M6 screws (user supplied), as

shown in Figure 14. Do

not completely fasten the screws until you mount the switch chassis

in the rack.

Figure 14 Attaching the rear mounting brackets to a rack with the wide flange inside the

rack

Figure 15 Attaching the rear mounting brackets to a rack with the wide flange outside

the rack



13

4. Mount the switch chassis in the rack:

a. Install cage nuts (user-supplied) in the mounting holes in the front rack posts. Make sure the

corresponding cage nuts on the front and rear rack posts are at the same height.

b. One person supports the chassis bottom with one hand, holds the front part of the chassis

with the other hand, and pushes the chassis into the rack gently.

Make sure the shoulder screws closely contact with the upper edges of the rear mounting

brackets, as shown in Figure 16 a

nd Figure 17.

c. The other person uses M6 screws (user-supplied) to attach the front mounting brackets to

the front rack posts. Make sure the switch is installed securely in the rack.

Figure 16 Mounting the switch in the rack (with the wide flange of the mounting brackets

inside the rack)

Figure 17 Mounting the switch in the rack (with the wide flange of the mounting brackets

outside the rack)

Page is loading ...

H3C S5130-30C-HI, S5130-30C-PWR-HI, S5130-30F-HI, S5130-30S-HI, S5130-34C-HI, S5130-54C-HI, S5130-54C-PWR-HI, S5130-54QS-HI, S5130-54S-HI, S5130-HI Series Installation guide

Related papers

Other documents