—
ABB MEASUREMENT & ANALYTICS | INSTRUCTION | IN/RANDC/007-EN REV. A
SM500F
Field mountable paperless recorder
Battery replacement
Measurement made easy
1 Introduction
This publication details replacement of the battery
(B12454) fitted to the processor board of the
SM500F Paperless recorder. The procedure must be
carried out by a trained technician.
Tools required
• T8 Torx driver
2 For more information
Further information is available from:
www.abb.com/recorders
or by scanning these codes:
Sales Service
3 Safety
IMPORTANT NOTE
Dispose of the old components as detailed in the
instruction manual (IM/SM500F).
SM500F
field mountable
paperless recorder
2 IN/RandC/007-EN Rev. A | SM500F | Paperless recorder | Battery replacement
4 Replacing the battery
1. Isolate the recorder from the power supply.
Referring to Fig. 4.1:
2. Unlock the door with the key (if required) A, press release
catch B and open the door.
Referring to Fig. 4.2:
3. Use a T8 Torx driver to remove 6 Torx screws C securing
the door assembly rear cover and remove the rear cover.
Referring to Fig. 4.3:
4. Disconnect processor board flexi-cable D, display
flexi-cable E keypad membrane cable F and inverter
cable (if fitted) G from the processor board. Lift out and
discard the processor board.
5. Turn the processor board over.
Referring to Fig. 4.4:
6. Remove battery H and insert replacement.
Referring to Fig. 4.3:
7. Position the processor board in the door housing and
reconnect inverter cable G (color recorders only – if fitted)
keypad membrane cable F, display flexi-cable E and
processor board flexi-cable D.
Referring to Fig. 4.2:
8. Refit the door assembly rear cover and use a T8 Torx driver
to secure 6 Torx screws C.
9. Close and lock the door.
10. Restore the recorder's power supply.
CAUTION – Property damage
The recorder is vulnerable to electrostatic damage.
Wear an anti-static strap or place the instrument on
an anti-static workbench.
Fig. 4.1 Opening the door
Fig. 4.2 Removing the rear cover
A
B
C
Fig. 4.3 Disconnecting / removing the processor board
Fig. 4.4 Replacing the battery
D
E
F
H
SM500F | Paperless recorder | Battery replacement | IN/RandC/007-EN Rev. A 3
5 Setting the time and date
1. Enter the Configuration level of the SM500F.
2. Enter password (if required) and select Edit current
configuration.
3. Select the Common configuration parameter:
The Common Configuration menu is displayed:
4. Use the arrows to highlight the Time tab:
5. Press the key to select the Date and time
parameter.
A warning dialog is displayed:
6. Press .
The Date and time menu is displayed:
7. Set the required time and date.
8. Once finished, press and exit and save the
configuration as normal.
Important note
Once the battery has been removed, the battery failed
icon is displayed on the front panel of the unit. To
restore normal operation, the correct time and date must
set.
Important note
Changing the time will potentially cause loss of
data. Ensure that all data archiving is up to date
before proceeding.
IN/RandC/007-EN Rev. A 12.2018
—
We reserve the right to make technical changes or modify the contents of this document
without prior notice. With regard to purchase orders, the agreed particulars shall prevail.
ABB does not accept any responsibility whatsoever for potential errors or possible lack of
information in this document.
We reserve all rights in this document and in the subject matter and illustrations contained
therein. Any reproduction, disclosure to third parties or utilization of its contents – in
whole or in parts – is forbidden without prior written consent of ABB.
© ABB 2018
—
ABB Limited
Measurement & Analytics
Howard Road, St. Neots
Cambridgeshire, PE19 8EU
UK
Tel: +44 (0)0870 600 6122
Fax: +44 (0)1480 213 339
Email: instrumentat[email protected]
ABB Inc.
Measurement & Analytics
125 E. County Line Road
Warminster
PA 18974
USA
Tel: +1 215 674 6000
Fax: +1 215 674 7183
abb.com/measurement
/