Restmoment RX-M3500B User manual

—— ——

Restmoment digital conference system

RX-3500 SERIES

Installation operation

RESTMOMENT ELECTRONIC CO.,LTD

www.restmoment.com

-1-

CONTENTS

RESTMOMENT DIGITAL CONFERENCE SYSTEM...............................................................................................0

RX-3500 SERIES..............................................................................................................................................................0

PART 1 SAFETY OPERATION ......................................................................................................................2

1.1 SAFETY OPERATION.............................................................................................................................................2

PART 2 SYSTEM CONNECTIO2.1...............................................................................................................................3

SYSTEM CONNECTION DIAGRAM...........................................................................................................................3

PART 3 SYSTEM PORTS AND KEYS..........................................................................................................................4

3.1 PORTS AND KEYS ........................................................................................................................................................4

3.1.1 RX-3500 series controller...................................................................................................................................4

3.1.1.1 RX-3500 front panel ports...............................................................................................................................................4

3.1.1.2 RX-3500 back panel ........................................................................................................................................................4

3.1.2 RX-3500 serial unit.............................................................................................................................................5

3.1.2.1 RX-3500..........................................................................................................................................................................5

3.1.2.2 RX-3500..........................................................................................................................................................................7

4.1 RX-3500 HARDWARE CONNECTION............................................................................................................................7

4.1.1 system controller and unit connection.............................................................................................................7

4.1.2 unit and unit connection. .................................................................................................................................8

4.1.3 system controller and speed done camera connection.....................................................................................8

4.2 SYSTEM CONTROLLER ADJUSTMENT...........................................................................................................................9

4.2.1 System controller interface and key:................................................................................................................9

4.2.2 main menu instruction:..................................................................................................................................10

4.2.3 new system adjustment steps; ........................................................................................................................10

4.2.3.1 Adjustment steps:........................................................................................................................................................10

4.2.3.3 setup work mode in controller .......................................................................................................................................14

4.2.3.5 setup video trace in controller.....................................................................................................................................15

4.2.3.6 setup system function in controller................................................................................................................................18

4.3 RX-MBVS SOFTWARE SETUP AND ADJUSTMENT......................................................................................................19

4.3.1 RX-MBVS RX-MBVS function ....................................................................................................................21

4.3.1.1 System setting................................................................................................................................................................23

4.3.1.2 Attendance file............................................................................................................................................................24

4.3.1.3 genda management .....................................................................................................................................................24

4.3.1.4 screen info...................................................................................................................................................................24

4.3.1.5 ideo tracing .................................................................................................................................................................25

4.3.1.6 onference video...........................................................................................................................................................26

4.3.1.7 Help...............................................................................................................................................................................26

4.3.1.8 Back...............................................................................................................................................................................26

www.restmoment.com

-2-

PART 5 FAQ....................................................................................................................................................................27

Part 1 SAFETY OPERATION

1.1 SAFETY OPERATION

Thanks to the use of RESTMOMENT conference system. Please read

this operation carefully before you use the equipment, and operate it as request.

1、Please confirm the power supply system is under the requirement of the equipment

normal level.

2、Please protect cable not be treaded and pressed, special joint.

3、When setup system, should insure the connection of ground is well, don’t use 2 Pin

plug. Input voltage AC 100～240V50Hz

4、Resist 1.5M free falling body industrial level aseismatic standard.

5、Please notice the system environment, not too hot or too cold, keep the suitable

temperature

6、Equipment power supply will get hot when it work, so should keep work

environmental aeration, avoid hot temperature.

7、 Please turn off main supply in wet weather or free time.

8、Please pull out power supply before below operation.

☆ Apart or rerun setup any spare parts

☆ Reload any plug or other conncetions.

9、Equipment with AC 100～240V components, please don’t open machine cover.

Not professional, please don’t maintain equipment privately.

10、All kinds of chemical was forbidden to contact any part of the appliance

11、Before turn on controller power, please comb-out system connection, and

controller setup.

www.restmoment.com

-3-

PART 2 SYSTEM CONNECTIO2.1

system connection diagram

www.restmoment.com

-4-

PART 3 system ports and keys

3.1 ports and keys

3.1.1 RX-3500 series controller

3.1.1.1 RX-3500 front panel ports

1、Mounting hole for 19 inch stand

2、Front panel

3、LCD screen, adjust brightness and contrast.

4、5-dimensional direction operate、control key

5、Switch, with electrifying indicator

6、Mounting hole for 19 inch stand

3.1.1.2 RX-3500 back panel

1、Power port: Input AC 100~240V, 4A 50-60Hz

2、RS232 interface (PC): Computer control system interface.

www.restmoment.com

-5-

3、RS232 interface(CCU): Central control system interface.

4、USB interface ( CONTRUL IN): Function extension interface. Reserve for function extension

5~8、4 PCS 6P DIN digital interfaces ( DRAGOMAN ): 4 channels conference unit output. Can

connect all digital all conference unit equipment in same series, and single function equipment.

9、6P DIN digital interface ( EXTEND ): Extension main unit digital interface, connect to EXTEND

IN port of extension main unit.

10、RCA Audio interface ( LINK OUT ): Audio output interface of System controller, can connect

peripheral amplifying system or recording system

11、RCA Audio interface ( LINK IN ): Input interface of the third sound source

12、RCA Audio interface ( LINK OUT ):Audio output interface of System controller, can connect

peripheral amplifying system or recording system

13、RCA Audio interface ( LINK IN ): Input interface of the third sound source

14、6.3mm MIC input socket

15、Cannon balance interface MIC, connect MIC

16、RS 485 interface: Connect to camera. Connect positive and negative electrode correctly.

17~18、2 USB interfaces ( CONTROL OUT ): Function extension interface. Reserve for function

extension

3.1.2 RX-3500 serial unit

3.1.2.1 RX-3500

RX-C/D 3500 unit front panel schematic diagram

1. Unit LCD display

* Display related information

2. MENU multi-complex function key

*Function selection key. Used for simultaneous

interpretation receiving channel selection and

unit function setting enter and exit

*Used as digital key 1/6 when input unit location

3. Multi-complex function

www.restmoment.com

-6-

* Left key. Select function menu of the unit.

Cursor move key

*Used as digital key 2/7 when input unit location

Utilizada para decrementar volumen.

4．PRIOR Chairman function control key, essage rapid key

* Conference Chairman operate chairman ontrol right

*Set MIC management mode.

Utilizada para incrementar volumen.

5. Multi-complex function

*Right key. Select function menu of the unit. Cursor move key

*Used as digital key 3/8 when input unit location

6. Multi-complex function

* MIC floor “ON/OFF” key

*Switching key. Inputting mobile cursor on location to function key MIC ON/OFF key indicator

when input unit location

7. Multi-complex function

*Act as ENTER key when set unit function or parameter

*Used as digital key 4/9 when input unit location

8. Multi-complex function

* message rapid key

*Used as digital key 5/0 when input unit location

9. Loudspeaker inside

10. Unit earphone jack

*Monitor the language of corresponding channel

*Listen to the language of corresponding channel

11. Chairman / Delegate unit IC card

www.restmoment.com

-7-

Chairman / Delegate unit sign-in and other function

12. Gooseneck microphone: With red ring to indicate floor

13. Red indicating ring: Indicate the microphone is working when the light is on.

14. Microphone: High Sensitivity, Cardioid, Electret condenser microphone

3.1.2.2 RX-3500

RX-C/D 3500 unit back panel schematic diagram

1. Screw hole

2.Shake proof and corrosion

proof rubber pad

3.IN 6 pin socket

4.Wire chase

5.OUT 6 pin socket

setup and function RX-MBVS

RX-MBVS is RESTMOMENT digital conference system RX-3500 serial software.

When it work with conference system, could manage MIC, and have sign-in、vote、

video function. It can’t work without hardwork.

4.1 RX-3500 hardware connection

4.1.1 system controller and unit connection.

system controller and unit connection use 6P cable. system controller Output port connect the

first unit IN port. Every Output could connect 20 units. For avoiding interference, system

controller cable should have special duct. Standard cable length is 10 M, could order more long

cable as actually.

Notice:

www.restmoment.com

-8-

Please don’t change the connection between unit and system controller. It could

lead Anomalies.

4.1.2 unit and unit connection.

Hand-in-Hand connection. Unit with 6P-2M cable. The first unit Out port to the

second unit In port. The second unit Out port to the third unit In port. Followed

by analogy.

4.1.3 system controller and speed done camera connection.

speed done camera, have ceiling and wall-mounted mode. Camera high less than 2-3 M. The

distance between camera and rostrum is 10-15M. Camera need independence power supply,

should be setup with 100～240V socket

System controller have 8 video input, 4 video output, could handle 8 PCS

camera.

Camera double Pin cable connect corresponding video port of system

controller.

For instance, the camera address No is 1, video info should connect the

first input.

Camera communication adopt RX-485 transmit way. For insure transmit

distance and anti-jamming, suggest use twisted-pair, from camera RS-485 +/-

port to system controller RS-485 +/- port.

Camera and keyboard connection as above.

Notice:

Please don’t mess camera +/-, otherwise, will lead unusual situation.

Please don’t use software and keyboard for camera simultaneous. It will

lead camera out off control.

www.restmoment.com

-9-

4.2 system controller adjustment

Insure system controller and unit connection, then turn on system controller power, it

will check automatically.

4.2.1 System controller interface and key:

ADCS System controller interface

ADCS System controller display interface ADCS System controller operate interface

Four-dimensional key“up” Four-dimensional key“down”

Four-dimensional key“left” Four-dimensional key“right”

MENU／CONFIRM

system controller standby interface:

standby interface system main menu

www.restmoment.com

-10-

enter main menu

Press MENU／CONFIRM, enter system main menu. See photo

4.2.2 main menu instruction:

Conference event: edit conference event and check agenda result.

Work mode: setup unit work mode.

Speaker set: setup output and input volume.

Video-tracing: setup panorama/unit video tracing.

System setup: unit NO、chairman unit、LED setup、language、IC card and speech count

down time.

Help: system version No.

Exit: Exit system menu.

4.2.3 new system adjustment steps;

4.2.3.1 Adjustment steps:

Si el sistema viene reseteado de fábrica y no se utilizan tarjetas IC, tiene que deshabilitarse esta opción.

MENU Æ SYSTEM SETTING Æ OTHER SETTING Æ IC CARD OFF

1)Check connection as system connection diagram, then turn on system controller. System

check units automatically and show equipment list. Please confirm the equipment list is the same as

actually quantity. After than, system enter standby interface.

www.restmoment.com

-11-

Notice: in this list, the chairman unit is executive chairman.

2) setup unit quantity and ID No.

Press , enter system main unit, select system setup, then select to edit ID No,

press again. Move cursor to “start” key, press at previous.

El 0050 es el número máximo de unidades del sistema actual. Debe ponerse el nº real.

units prompt as below photo:

When press unit’s “MIC” key, system will send this unit one ID No, as below photo

When all units have ID No, close this operation.

Notice:

System need re-edit ID No in below instance

1、Setup new system

2、Move、change、add or delete units

3、unit prompt no ID No.

Unit prompt no ID No as below photo,

www.restmoment.com

-12-

At this moment, we could edit ID No for this unit. Enter “Edit ID No” , select right key, edit one

ID No, as below photo:

Setup ID No, move cursor to “start”, press . At previous, press unit’s “MIC” key.

4.2.3.2 vote in controller

Para poder realizar una votación es necesario identificar previamente las unidades que van a poder votar.

Esto se hace mediante la opción Sign in.

Before vote, should setup units quantity. Vote people quantity should be the same as setup

quantity ( for instance, we setup units quantity as 50.

Press , enter system main menu, then enter Meeting event setup interface, see below

photo

menu include:

New sign in: setup sign in conference event, enter sign in interface, press “start”, see below

photo:

Ought seria el número de unidades totales. Al pulsar start se activará una cuenta atrás de 30s para que todas

las unidades activas puedan darse de alta en la votación pulsando su propia tecla mic. Para finalizar el

proceso sin acabar la cuenta atrás debe pulsarse la tecla menú, que la dejará con solo 2s de margen.

www.restmoment.com

-13-

New vote: setup vote conference event, enter vote interface, press “start”. More than 10 vote

modes could be selected. see below photo.

Al pulsar start se activará una cuenta atrás de 30s para que todas las unidades puedan votar. Para finalizar el

proceso sin acabar la cuenta atrás debe pulsarse la tecla menú, que la dejará con solo 2s de margen.

New poll: setup poll conference event, enter poll interface, press “start”. Many poll modes

could be selected, for instance, 5 elect 4, see below photo

Result Display: enter result display interface, could see vote、sign in and poll

result.

see below photo

result display

sign in result inquiry

vote result inquiry

www.restmoment.com

-14-

poll result inquiry

Meeting Setting: setup count-down time and count rule, see below photo

Pre-> Si, Agt->-No, Abs-> Abstensión

Back: back to previous menu

4.2.3.3 setup work mode in controller

Press enter system main menu and Mode setting interface, see below photo:

this menu include:

Limit mote: set the number of delegates permitted to speak at the same time. see below photo

Al limitar a una unidad abierta pasaría a funcionar como modo FIFO.

FIFO mode :microphone key control with override of the active microphones. see below

photo.

Este modo funciona realmente como LIFO.

www.restmoment.com

-15-

Apply mode: microphone key with request –to-speak registration (AUTO). see below photo

Voice mode: voice-activated microphones with selectable threshold. see below photo

4.2.3.4 setup volume in controller

Press enter system main menu and volume setup interface, see below photo:

This menu include

Input volume: could adjust volume as meeting room request.

Output volume: could adjust volume as meeting room request.

4.2.3.5 setup video trace in controller

www.restmoment.com

-16-

Press enter system main menu and volume setup interface, see below photo:

This menu include:

Camera parameter: setup baud rate、protocol、save No. See below photo

Could setup 8 cameras with difference protocol and baud rate.

Operation option: setup scene、save No. See below photo

Setup scene

1．Unit:001 option, select scene 0001, press .

Notice: left and right key adjust camera panorama. One camera could have 2 panorama.

2．Move cursor to , adjust camera panorama position.

Notice: “up down、left right” is for camera moving speed.

3．Adjust Focus、Aperture、Zoom、up down、left right.

Notice: “up down、left right” is for camera moving speed.

4．Move cursor to “ camera 01”, select correspondence panorama.

www.restmoment.com

-17-

Notice: Camera address No will change automatically when adjust panorama position.

5．Move cursor to save NO:001, select one to save camera position.

6．Move cursor to save “ panorama 001” as preset point

Notice: Save No can’t repeat. back to previous menu, RST meat clear all save No.

setup unit tracing steps: ( see below photo)

1、Select “unit 0001”, press .

2、Move cursor to , preset unit position

3、“up down、left right” is for camera moving speed.

4、Move cursor to “ camera 01”, select correspondence unit.

5、Move cursor to save NO:001, select one to save camera position.

6、Move cursor to save “ unit 001” as preset point

Notice: Save No can’t repeat. back to previous menu, RST meat clear all save No.

Video matrix: setup controller 4 matrix video output. See below photo

Out put 1-4 meant video output; 1-8 meant 8 cameras.

For instance, setup output 1 with 1-3 cameras video signal, as below steps:

1、Move cursor to “output1”, press , move cursor to 1-3, press , grounding is

black.

2、Move cursor to save it.

Turn off video:

www.restmoment.com

-18-

As above photo: preset camera 1 to trace unit No1-5, setup 4 panorama.

“camera 1 corresponding MIC” setup unit 1-5.

3 options

“previous unit”

“ No action”

“ID 0001”

“ turn off all to panorama” camera switch to panorama when all units are off.

“1~4”meant panorama 1~4. black grounding.

“time” meant camera 1 panorama switch time.

“cameras switch” panorama switch have two types.

“gradation” select panorama gradation according to port.

“dependence” select panorama gradation according to camera No.

for instance

Port 1 have camera 1、camera 2、camera 3, all cameras have 4 panoramic positions.

“gradation”, panoramic switch gradation: 1a、1b、1c、1d、2a、2b、2c、2d、3a、3b、3c、3d、

4a、4b、4c、4d

“dependence”, panoramic switch gradation: 1a、2a、3a、4a、1b、2b、3b、4b、1c、2c、3c、

4c、1d、2d、3d、4d

4.2.3.6 setup system function in controller

Press , enter system main menu, then enter system setup interface, see below photo

www.restmoment.com

-19-

This menu include:

Edit No: setup total human quantity and unit No.

Status setup: setup executive chairman unit.

One system only have one executive chairman unit. ID item display all common chairman unit.

Screen setup: setup LED brightness and contrast. See below photo:

Menu language setup: setup controller language. See below photo:

System have Chinese and English. Could order other languages.

Other setup: IC card sign-in function, speech count down time. As below photo:

Back: back to previous menu.

4.3 RX-MBVS software setup and adjustment.

Page is loading ...

Restmoment RX-M3500B User manual

This manual is also suitable for

Restmoment RX-M3500B User manual

Other documents