Page is loading ...
Page |
1
PO#:13864
HO730400TX
Kedzie Multilevel Desk
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
www.seidal.com
Page |
2
1) Quantity
of 1
Left Top Panel
2) Quantity
of 1
Centre Top Panel
3) Quantity
of 1
Right Top Panel
4) Quantity
of 1
Left Side Panel
5) Quantity
of 1
Right Side Panel
6) Quantity
of 1
Down Right Side Panel
7) Quantity
of 1
Left Middle Panel
8) Quantity
of 1
Right Middle Panel
9) Quantity
of 1
Left Bottom Panel
10) Quantity
of 1
Centre Bottom Panel
11) Quantity
of 1
Right Bottom Panel
12) Quantity
of 1
Right Shelf Panel
Kedzie Multilevel Desk
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage
Page |
3
13) Quantity
of 2
Small Drawer Front Panel
14) Quantity
of 1
Big Drawer Front Panel
15) Quantity
of 3
Drawer Left Side Panel
16) Quantity
of 3
Drawer Right Side Panel
17) Quantity
of 2
Small Drawer Back Panel
18) Quantity
of 1
Big Drawer Back Panel
19) Quantity
of 2
Small Drawer Bottom Panel
20) Quantity
of 1
Big Drawer Bottom Panel
21) Quantity
of 1
Drawer Bottom Panel
22) Quantity
of 1
Drawer Left Side Panel
23) Quantity
of 1
Drawer Right Side Panel
24) Quantity
of 1
Drawer Back Panel
25) Quantity
of 1
Centre Back Panel
26) Quantity
of 1
Left Back Panel
27) Quantity
of 1
Right Back Pane1-l
Page |
4
28) Quantity
of 1
Right Back Panel-2
29) Quantity
of 1
Metal Front Frame
30) Quantity
of 1
Metal Back Frame
31) Quantity
of 4
Top Stretcher
32) Quantity
of 2
Bottom Stretcher
A) Quantity
of 30
Cam Bolts
B) Quantity
of 30
Cam Locks
C) Quantity
of 36
Wood Dowels
Dia. 5/16"x1-1/4"
D) Quantity
o
f 24
Bolt Dia. 1/4x3/4” L
E) Quantity
o
f 24
Spring Washer Dia.1/4”
F) Quantity
o
f 24
Flat washer Dia.1/4” x3/4”
G) Quantity
of 1
Allen Wrench
H
)
Quantity
of 54
Screw Dia. 1/8” x 5/8”L
I) Quantity
of 4
Knob
Page |
5
J) Quantity
of 4
Bolts
Dia. 5/32”x 1”L
K) Quantity
of 28
Screw
Dia. 5/32” x 1L
L) Quantity
of 4
Metal Nut
M) Quantity
o
f 4
Bolt Dia. 1/4x1-1/2” L
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the surface
with rough or abrasive objects.
For replacement parts or questions, please call
Customer Service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)
Page |
6
Figure 1
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on Centre Bottom Panel (10).
Screw Cam Bolts (A) into threaded holes
on Left / Right Middle Panel (7/8).
Attach Left / Right Middle Panel (7/8) to
Bottom Panel (10) by inserting Cam Bolts
(A) and Wood Dowel (C) into
corresponding holes until all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
Figure 2
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on pre-assembled unit from figure 1.
Screw Cam Bolts (A) into threaded holes
on Centre Top Panel (2).
Attach Centre Top Panel (2) to
pre-assembled unit from figure 2 by
inserting Cam Bolts (A) and Wood Dowel
(C) into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
Kedzie Multilevel Desk
Assembly Instructions
B
A
C
10
C
Page |
7
Figure 3
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on Left Side Panel (4).
Screw Cam Bolts (A) into threaded holes
on Left Bottom Panel (9).
Attach Left Bottom Panel (9) to Left Side
Panel (4) by inserting Cam Bolts (A) and
Wood Dowel (C) into corresponding holes
until all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
Figure 4
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on Right Side Panel (5) & Lower
Right Side Panel (6).
Screw Cam Bolts (A) into threaded holes
on Right Shelf Panel (12).
Attach Right Shelf Panel (12) to Right Side
Panel (5) & Down Right Side Panel (6) by
inserting Cam Bolts (A) and Wood Dowel
(C) into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
5
12
C
Page |
8
Figure 5
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on pre-assembled unit from figure 4.
Screw Cam Bolts (A) into threaded holes
on Right Bottom Panel (11).
Attach Right Bottom Panel (11) to
pre-assembled unit from figure 4 by
inserting Cam Bolts (A) and Wood Dowel
(C) into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
Figure 6
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on pre-assembled unit from figure 5.
Screw Cam Bolts (A) into threaded holes
on pre-assembled unit from figure 2.
Attach pre-assembled unit from figure 2 to
pre-assembled unit from figure 5 by
inserting Cam Bolts (A) and Wood Dowel
(C) into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
11
11
Page |
9
Figure 7
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on pre-assembled unit from figure 3.
Screw Cam Bolts (A) into threaded holes
on pre-assembled unit from figure 6.
Attach
pre-assembled unit from figure 3 to
pre-assembled unit from figure 6 by
inserting Cam Bolts (A) and Wood Dowel
(C) into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
Figure 8
Start with finger to help align Cam Bolts.
Insert Cam Locks (B) into corresponding
holes on
pre-assembled unit from figure 7.
Screw Cam Bolts (A) into threaded holes
on Top Panel (1/3).
Attach Top Panel (1/3) to pre-assembled
unit from figure 7 by inserting Cam Bolts
(A) and Wood Dowel (C) into
corresponding holes until all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver.
9
A
C
A
C
Page |
10
Figure 9
Attach Back Panels (25/26/27/28) to back
of the unit with Screws (H).
Tighten Screws (H) with Phillips
screwdriver
.
Figure 10
Attach Drawer Side Panels (15/16) to
Drawer Back Panel (18) using Screws (K).
Insert Drawer Bottom Panel (20) into
grooves of Panels (15/16/18).
Attach Drawer Front Panel (14) to
assembled unit using Screws (K).
Attach Knobs (I) to Drawer Front Panel
(14) using Bolts (J).
Tighten Bolts and Screws with Phillips
screwdriver.
Repeat process for drawer
panel(15/16/17/19/13)
28
27
26
25
H
Page |
11
Figure 11
Connect Drawer Back Panel (24) to
Drawer Bottom (21) using Wood Dowels
(C). Attach using Screws (K).
Connect Drawer Side Panels (22/23) to
drawer using Wood Dowels (C). Use Bolts
(M), Metal Nuts (L) and Screws (K) to
attach Drawer Side Panels (22/23).
Tighten bolts and screws with Allen
Wrench (G) and Phillips screwdriver.
Attach Knob (I) to Drawer Bottom (21)
using Bolts (J).
Tighten bolts with Phillips screwdriver
Figure 12
Attach the Top Stretchers (31) and Bottom
Stretchers (32) to Metal Back Frames (30)
with Bolts (D), Spring Washers (E) and Flat
Washers (F).
Tighten bolt with Allen Wrench (G).
21
M
L
C
D
G
Page |
12
Figure 13
Attach the Metal Front Frames (29) to Top
Stretchers (31) and Bottom Stretchers (32)
with Bolts (D), Spring Washers (E) and Flat
Washers (F).
Tighten bolt with Allen Wrench (G).
Figure 14
Attach pre-assembled unit from figure 13
to pre-assembled unit from figure 10 with
screw H
Tighten Screws (H) with Phillips
screwdriver.
D
G
H
Page |
13
Figure 15
Insert drawer into assembled unit.
Make sure slides glide smoothly in and
out.
Note: There is a lever located on male
slide for bottom drawer slide. Push
lever to either side in order to detach
male slide from female slide.
Figure 16
Page |
14
Figure 17
Figure 18
Now your Kedzie Multilevel Desk is ready
to us! is ready to us!
Page |
15
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s). If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas),
Mon-Fri 9am – 4pm CST, or email us at servic[email protected]. Please ask for customer service representative for
issues involving damages or replacement parts. Please ask for technical assistance representative for any issues
with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Parts Replacement Form
Customer Service: 1-800-633-5096
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
/
