anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
Installation Instructions
Mixx Tables, Benches, and Stools
(4) 3/8" Rubber Washers
90130A050
Step-by-Step Installation Sequence
Product ships fully assembled.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the Mixx product.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
Hammer Drill Masonry Drill Bit Set
1/8", and 1/4"
Hammer
Pencil
7/16"Wrench
Wire BrushLevel
Safety Glasses
SUPPLIED HARDWARE:
OPTIONAL HARDWARE:
(4) 1/4" x 3.25"
Stainless Steel Stud Anchors
with Nut & Washer
(8) Plastic Feet (16) Double Sided
Tape Strips
(4) Anchoring Glides
Step-by-Step Installation Sequence
Installation Instructions
Mixx Tables, Benches, and Stools
7. Use the hammer to x the anchor into the drilled hole by giving it several
hammer blows.
8. Repeat steps 4 - 7 until all anchors are installed.
3.
2.
1.
4.
5.
6.
Mark the location of the holes with a pencil. To verify the alignment of the
anchor markings you may reference the bottom of page 3.
Unscrew the current glides on the bottom of your Mixx product and replace
them with the mounting glides. Make sure to align the shape of the glide with
the shape of the legs.
Place the Mixx product in the desired location. Apply the two pieces of the
double side tape to the top of the mounting glide. Place one plastic foot onto
the top making sure it is aligned properly with the shape of the glide. Repeat
the process on the bottom. Assemble the three remaining glides in the same
manner.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 1/8" diameter drill bit followed by a 1/4" diameter bit.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
!
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
4
7
6
2.1
2.2
1
A rubber washer is a suitable replacement option. Mount the Mixx product
to the ground by placing a washer and a nut onto each anchor. Leave the hardware
nger tight until all of them have been installed. Verify that the Mixx product is level
before tightening the anchors. Tighten all of the hardware with a 7/16" wrench.
10.
!
9. Remove the nuts and washers o of the anchors. Align the mounting holes of the
Mixx product over top of the anchors and slide it down into place.
Copyright 2019 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
01/11/2019
Installation Instructions
Mixx Tables, Benches, and Stools
FOOT MOUNT SIZE CHART
SKU # Width Length
MIX2927
MIX2937 12.69" 12.69"
MIX2960 12.69" 57.19"
MIX2925
MIX2935 31.44" 31.44"
MIX2945
MIX2955 31.44" 69.19"
MIX2920
MIX2930 38.94" 38.94"
MIX2940
MIX2950 38.94" 69.19"
7)'8-32%%
7'%0)
% %
% %
& &
THIRD ANGLE PROJECTION
TOLERANCES UNLESS NOTED:
X
1 X.X
.5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX
.015625 ANGULAR ± 1°
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125
.0625 DURING COATING.
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
DRAWN
Mixx 60" Bamboo Bench
SIZE
BMIX2960B_SPEC
DATE 4/11/2016 SCALE
.09375:1 SHEET
DWG NO
TITLE
B. MENDEZ
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
REV
1 OF
003
1
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 ORIGINAL PRINT NONE 4/11/16
002 SIZE REDESIGN NONE 6/28/16
003 REDESIGNED COMPLETELY
WELDED NONE 10/6/16
*6328:-); 7-():-);
834:-);
Length
Width
Ø .40"
(4 PLCS)
9
10.1 10.2
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Anova M2006 Installation guide
-
-
-
-
-
-
-
-
-
