luminii STENOS Suspended Track Installation guide

Type
Installation guide

The luminii STENOS Suspended Track is a versatile and stylish lighting system designed for use in a variety of commercial applications. It features a suspended aircraft cable design that allows for flexible positioning of the track and fixtures, making it ideal for use in retail stores, restaurants, galleries, and other commercial spaces. The track is compatible with a wide range of luminii fixtures and accessories, allowing you to create a custom lighting solution that meets your specific needs.

The luminii STENOS Suspended Track is a versatile and stylish lighting system designed for use in a variety of commercial applications. It features a suspended aircraft cable design that allows for flexible positioning of the track and fixtures, making it ideal for use in retail stores, restaurants, galleries, and other commercial spaces. The track is compatible with a wide range of luminii fixtures and accessories, allowing you to create a custom lighting solution that meets your specific needs.

*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
A. READ ALL INSTRUCTIONS
B. DO NOT INSTALL THIS TRACK IN DAMP OR WET LOCATIONS
C . DO NOT INSTALL ANY PART OF THE TRACK SYSTEM LESS THAN 5 FEET ABOVE THE FLOOR
D. DO NOT INSTAL ANY LUMINAIRE ASSEMBLY CLOSER THAN 6 INCHES FROM ANY CURTAIN OR SIMILARCOMBUSTIBLE MATERIAL
E. DISCONNECT ELECTRICAL POWER BEFORE ADDING TO OR CHANGING THE CONFIGURATION OF THE TRACK
F. DO NOT ATTEMPT TO ENERGIZE ANYTHING OTHER THAN LIGHTING TRACK LUMINARES ON THE TRACK. TO REDUCE THE RISL OF
FIRE AND ELECTRIC SHOCK, DO NOT ATTEMPT TO CONNECT POWER TOOLS, EXTENSION CORDS, APPLIANCE, OR THE LIKE TO
THE TRACK.
IMPORTANT SAFET Y INSTRUCTIONS!
WHEN INSTALLING OR USING THIS TRACK SYSTEM, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING:
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
1 / 14
Suspended Aircraft Cable
Track System
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
8’ Individual Track
8‘
4’ Individual Track
4‘
12’ Individual Track
12‘
16’ Continuous Run with Power Feed Straight Joiner
8‘ 8‘
* Track sections longer than 96” require a middle suspension point. Use diagrams for reference.
Example Track Layouts
16’ Continuous Run with Straight Joiner
8‘ 8‘
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
2 / 14
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
1
1.1 Start by removing the magnetic
finish plate on the Power Feed
Endcap. Loosen the cover plate
screws. Remove cover plate.
1.2 Insert power cable into power
feed endcap.
1.3 Slide the power feed endcap to the track housing and fasten the two set
screws to secure to the track.
1.4 Flip down and snap in the power feed
connector to the track housing. Perform
a continuity check between the track
conductors and power feed connector
wires to ensure the connector is seated
properly in the track.
1.6 Re-attach the cover plate by fastening the cover plate screws, then, attach
magnetic finish plate.
1. Power Feed Endcap Installation
1.5 Tighten the nylon
set screw until
the power cord is
secure. Take care
not to over-tighten
and damage the
power cord.
Cover Plate
Magnetic Finish
Plate
Cover Plate
Screws
Power Feed
Endcap
Power
Cable
Power Feed
Endcap
Power Feed
Endcap
Track Housing
Set Screws
Power Cord
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
3 / 14
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
2. Track Gripper Installation (used at end of runs or middle of track sections > 96” long)
2
2.1 Slide the nut to the back of the track housing channel and fasten the set
screw. Make sure the nut is fastened 1” +/- from the end of the track
housing.
2.2 Fasten gripper to the nut using the set screw and washer as shown.
1” +/-
Set Screw
Nut
Washer
Aircraft Cable
Mount
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
4 / 14
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
3. Blank Endcap Installation
3.1 Slide endcap into track housing.
3
3.2 Fasten set screw to endcap so
that it is secured to the track
housing.
Set Screw
Endcap
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
5 / 14
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
ceiling
S
S
c
c
r
r
e
e
w
w
/
/
A
A
n
n
c
c
h
h
o
o
r
r
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
S
S
c
c
r
r
e
e
w
w
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
4.2 If using the supplied toggle anchor, drill a 3/8” hole at all marked locations.
4.3 Feed the screw through the cap, washer, and toggle anchor and properly secure into place. Repeat for all remaining marks.
OR
4.4 If securing to a solid surface or into framing, feed the screw (not provided) through the cap and washer, and secure directly into the
surface. Repeat for all remaining marks.
4. Mounting Preparations
Note: Prior to installation all 24VDC wires must be present in junction box. Refer to
the power supply installation instruction for additional information.
Note: More than one person is recommended for this installation.
4.1 Measure the distance between the two standoff hubs. Then center the
fixture to the junction box and mark the distance of the two standoff
hubs to the ceiling.
Measure
Stenos Fixture Standoff Hub
Note: If not using the supplied toggle anchor, and installing to a hollow ceiling or concrete, must use a #6 screw size anchor, that must be rated for a
minimum of 30lbs.
standoff
location
marks
drill
bit
drill
anchor
cap
screw
washer
screw
cap
washer
anchor
4.2
4.3
4.4
4.3 4.4
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
6 / 14
4
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
5.1 While one person is holding the fixture, the
other will slide the power cable through the
strain relief bushing, canopy, and crossbar
assembly.
5.5 Tighten the set screw on the strain relief bushing to secure the position
of the power cable.
5.3 Insert the wire nut connections into the junction box, align the crossbar to the
junction box holes, and secure using the provided two #8-32 screws.
5. Canopy Installation (steps require multiple people)
5.2 Strip back the power cable and connect the track
wires (Red = Common 24V DC +, Black = Channel
1 24V DC -, White = Channel 2 24V DC -) to the
remote power supply wires.
5.4 Slide the canopy up to the crossbar and secure by threading the strain relief
bushing onto the crossbar assembly nipple.
Power Cable
Strain Relief
Bushing
Canopy
Backplate
Crossbar
Assembly
Can Be installed
without Aircraft
Cable Cap
Junction Box
#8-32 Screws
5.6 The same process would be followed without suspensions.
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
7 / 14
5
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
6.1 Unscrew ceiling mount cap. Un-tangle cable and insert through cap.
6.2 Tighten cap and feed aircraft cable into the gripper.
6.3 Tighten each threaded post into the ceiling mounted caps.
6. Track Hanging Instructions
6.4 Level the track and cut off any extra aircraft cable from the grippers.
6.2
6.3
6.5 This image shows if a canopy were to be installed offset of the
suspension.
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
8 / 14
6
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Straight Joiner L Joiner
7. Installation of Joiners without Power Feeds
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
9 / 14
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
7.1 Start by removing the magnetic finish plate and loosen the cover plate
screws. Then remove cover plate and power feed jumper.
7
7.2 Slide joiner into the track housings and tighten the set screws until secure.
7.3 Snap in the electrical jumper connector to the track housings. Perform a continuity check between the track conductors to ensure the connector is seated properly in
the track.
Electrical Jumper
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
10 / 14
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
7.4 Re-attach the cover plate and tighten screws to secure it to the joiner.
7
7.5 Attach the magnetic finish plate to joiner.
7.6 Follow step 6 for hanging instructions. NOTE: Same process will be done for L - joiners without power feeds.
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
11 / 14
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
8. Installation of Joiners with Power Feeds
Straight Joiner w/ Feed L Joiner w/ Feed
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
12 / 14
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
8.1 Start by removing the magnetic finish plate and loosen the cover plate
screws. Then remove cover plate and power feed jumper.
8
8.2 Slide joiner into the track housings and tighten set screws until the power
cord is secure. Take care not to over-tighten and damage power cord.
8.3 Insert power cable into power feed joiner and snap in power feed
connector to desired track housing (only one end joiner can be
energized). Perform a continuity check between track conductors and
power feed connector to ensure connector is seated properly in track.
8.4 Tighten nylon set screw, making sure not to damage power cord.
8.5 Re-attach the cover plate and tighten screws to secure it to the joiner.
8.6 Attach the magnetic finish plate to the joiner.
8.5 8.6
Nylon Set Screw
8.4
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
13 / 14
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
8.7 Follow step 5 for canopy installation and step 6 for hanging instructions.
8.8 When using a joiner with power feed, the aircraft cable gripers are to
be mounted on both track sections adjacent to the joner. (Use image for
reference)
8.8
Stenos Track System - Installation Instructions
Suspended Aircraft Cable
Please read all instructions prior to installation and keep for future reference!
• PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
• USE ONLY WITH CLASS 2 POWER UNIT
• 24 VOLTS DC
• SUITABLE FOR DRY LOCATIONS ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.8
02112022
14 / 14
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

luminii STENOS Suspended Track Installation guide

Type
Installation guide

The luminii STENOS Suspended Track is a versatile and stylish lighting system designed for use in a variety of commercial applications. It features a suspended aircraft cable design that allows for flexible positioning of the track and fixtures, making it ideal for use in retail stores, restaurants, galleries, and other commercial spaces. The track is compatible with a wide range of luminii fixtures and accessories, allowing you to create a custom lighting solution that meets your specific needs.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI