Golden Lighting 3602-L AB-RBZ Installation guide

Type
Installation guide
Assembly Instructions: 3602-L (Duncan)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Carefully remove all of the contents from the carton. See the
important notes above. Shut off the power at the circuit breaker
andcompletelyremovetheoldxturefromthewall,including
theoldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.One
endofnipple(F)shouldbeattachedtomountingstrap(A)with
washerandhexnuts(C,D)inplace.Theotherendshouldhave
canopy loop (H) attached.
Attachmountingstrap(A)tothejunctionboxusingmounting
screws(B)andascrewdriver.Tightensecurely.Unscrewcanopy
loop collar (I) from canopy loop (H). Pass canopy (G) over the
mountedcanopylooptotesttheheight.Approximatelyhalf
ofthecanopyloop’sexteriorthreadsshouldbeexposed,and
thecanopyloopcollarshouldtsnuglyontothecanopyloop.
Removecanopy(G)andadjusttheheightofnipple(F)and
canopyloop(H)untilthedesiredheightisreached.
ASSEMBLING THE FIXTURE
Bymeasuring,determinethecorrectlengthofchainneededfor
properhangingheight.Ifnecessary,useapairofplierstoopen
andremoveanyexcesschain.Attachoneofchainconnectors
(K)tochain(J).Passthexturewiresthroughtoploop(L).Pull
thewiresuntiltaut.Feedthexturewiresupthroughthechain
(everythreelinksorso),pullingthewiresuntiltaut.Usethefree
chain connector (K) to attach chain (J) to canopy loop (H). Slide
canopy loop collar (H) and canopy (G) down onto the chain/
wires. Pull the wires until taut. Trim the wires to the desired
lengthplus8to10inches.
CONNECTING THE WIRES
Haveanassistantsupportthextureweightwhilecompleting
thewiring.Cutawayexcesswire.Threadthexturewires
throughcanopyloop(H)andcanopy(G).Attachthexture’s
wirestothepowersupplywiresfromthejunctionbox.Connect
blacktoblack(orsmooth);whitetowhite(orribbed);ground
toground(greenorcopper).Twisttheendsofthewirepairs
together,thentwistonawireconnector.Makesurealltwistsare
inthesamedirection.Ifthereisnogroundwire(greenorcopper)
fromthejunctionbox,locategroundscrew(E)onmounting
strap(A)andwrapthexturegroundwirearoundthegreen
groundscrew(E).Useascrewdrivertosecuregroundscrew(E)
ontothemountingbracket.Tuckallwiresneatlyintothejunction
box.
FINISHING THE INSTALLATION
Pushcanopy(G)uptotheceilingandslidecanopyloopcollar(I)
upbeneaththecanopy.Tightlythreadcanopyloopcollar(I)onto
canopy loop (H) to secure canopy (G) in place.
Slide the shade (Q) over socket (M) and secure in place with
socketwasher(N)andsocketring(O).
Installlightbulb(P)(notincluded)inaccordancewiththexture’s
specications.Donotexceedthemaximumrecommended
wattage.
Place diffuser (R) and cover (S) up beneath the bottom of shade
(Q).Securethediffuserandcoverinplacebytighteningthe
provided screws. Please note: Diffuser (R) and cover (S) are packed
beneath Shade (Q) in the box.
Your installation is now complete. Turn on the power and test
thexture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
H
I
G
J
K
A
B
C
E
D
F
L
M
N
O
P
R
Q
  • Page 1 1

Golden Lighting 3602-L AB-RBZ Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI