Extron DTP T EU 332 User manual

Category
Video converters
Type
User manual

This manual is also suitable for

User Guide
DTP T EU 332
DTP T EU 232
DTP T MK 332
DTP T MK 232
DTP Systems
Two-Input Universal Twisted Pair Transmitters for
EU- and MK-type Junction Boxes
68-2713-01 Rev. C
01 19
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website,
www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf. 68-
290-01, sur le site Extron,
www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind
und die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website,
www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron,
www.extron.com.
Инструкция по технике безопасности Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и
других вопросах см. руководство по безопасности и
соблюдению нормативных требований Extron на сайте Extron:
www.extron.com, номер по каталогу - 68-290-01.
安全说明 简体中文
警告 产品上的个标志意在警告用户该产品机壳内有暴露的危险 电压,
险。
注意 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修说明
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容,敬请访问 Extron 网站
www.extron.com,参见
Extron 安全规范指南,产品编号 68-290-01
安全記事 繁體中文
警告: 若產品上使用此符號是為提醒使用產品機殼內存在
能會導致觸電之風險的未絕緣危險電壓
注意 若產品上使用此號,是為了提醒使用者設備隨附的用戶手冊中有
要的操作和維護(維修)説明
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳
細資訊,請瀏覽 Extron 網站:
www.extron.com,然後參閱《Extron 安全性
與法規遵守手冊》,準則編號 68-290-01。
安全上の注意 日本語
警告: この が製品上に表示されている場合は、筐体内に絶縁され
いない高電圧が流れ、電の危険があるを示ています
意: この 品上に表示されている場合は、の取扱説明書
( )
意を喚起するものです
安全上の注意、法規厳守、EMI/EMF適合性、その他の関連項
スト イト
www.extron.com よ り Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をださい
안전 지침 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(
www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause interference. This interference must be corrected at
the expense of the user.
ATTENTION: The Twisted Pair Extension technology works with shielded twisted pair
(STP) cables only. To ensure FCC Class A and CE compliance, STP cables and STP
Connectors are also required.
For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the “Extron Safety and Regulatory
Compliance Guide” on the Extron website.
Copyright
© 2016
-2019 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks
®
, registered service marks
(SM)
, and trademarks
(TM)
are the property of
RGBSystems, Inc. or Extron Electronics:
Registered Trademarks
(®)
Extron, AVTrac, Cable Cubby, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global Configurator, GlobalViewer,
Hideaway, Inline, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, NetPA, PlenumVault, PoleVault, PowerCage, PURE3,
Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork, TouchLink, V‑Lock, VersaTools, VN‑Matrix, VoiceLift,
WallVault, WindoWall, XTP, and XTPSystems
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
)
AAP, AFL (Accu‑RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto‑Image, CableCover, CDRS(ClassD Ripple Suppression),
DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital
Sync Validation Processing), eLink, EQIP, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP,
QS‑FPC(QuickSwitch Front Panel Controller), Room Agent, Scope‑Trigger, ShareLink, SIS, SimpleInstructionSet, Skew‑Free, SpeedNav,
Triple‑Action Switching, True4K, Vector™ 4K , WebShare, XTRA, ZipCaddy, ZipClip
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
Risk of property damage.
Risque de dommages matériels.
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E X! *X1&* X2)* X2#* X2! CE}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” is the capital
letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.
vDTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Contents
Introduction ................................................... 1
About this Guide ................................................. 1
About the Switching Transmitters ....................... 1
Features ............................................................. 3
Installation and Operation ........................... 4
Installation Overview ........................................... 4
Installing the Junction Box or European Cable
Channel System ................................................ 6
Rear Panel and Side Panel Features ................... 7
Mounting the Switching Transmitters .................. 9
Front Panel Connectors .................................... 10
Connection and Wiring Details .......................... 12
HDMI Connector........................................... 12
VGA Connector Wiring ................................. 13
TP Cable Termination and
Recommendations ....................................... 13
IR and RS‑232 Connector Wiring ................. 14
Power Supply Wiring .................................... 15
Operation ......................................................... 17
Front Panel LED Indicators ........................... 17
Switch Modes............................................... 17
EDID ............................................................. 17
Reset ............................................................ 17
Troubleshooting — If No Image Appears ........... 18
Remote Control ........................................... 19
Simple Instruction Set Control .......................... 19
Host‑to‑Switcher Communications ............... 19
Switcher‑Initiated Messages ......................... 19
Error responses ............................................ 20
Timeout ........................................................ 20
Using the Command and Response Table .... 20
Product Configuration Software ........................ 26
Installing the Software ................................... 26
Starting the Program .................................... 28
Downloading and Updating the Firmware ......... 29
Downloading Extron Firmware Loader .......... 29
Installing Firmware Loader ............................ 30
Downloading Firmware ................................. 30
Updating the Firmware ................................. 31
Extron Warranty .......................................... 33
Contents
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Contents vi
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Introduction 1
Introduction
About this Guide
About the Switching Transmitters
Features
About this Guide
This guide describes the following wallplate‑mounted switching transmitter models:
DTP T EU 332
DTP T EU 232
DTP T MK 332
DTP T MK 232
NOTE: In this guide:
The units are commonly referred to as “switchers” or as “switching transmitters.”
Unless specifically identified by the model name, the discussions in the guide apply
to any model.
The switchers output a signal to a compatible DTP receiver. This guide describes how to
install, operate, and configure the switcher.
About the Switching Transmitters
The switching transmitters covered in this guide are 2‑input VGA and HDMI switchers
with DTP transmitter outputs (see figure 1, on the next page). The switchers are HDCP
compliant, and support 1080p/60 Deep Color and 1920x1200 signals.
Each switcher selects between one analog VGA and one HDMI input, including embedded
audio (or DVI video with the appropriate adapter). The switcher converts the selected input,
an optional analog audio input, and bidirectional RS‑232 and infrared (IR) control signals to
a proprietary digital signal. The switcher and a compatible DTP receiver extend the usable
distance of video, audio, and control signals over a single Extron XTP DTP 24 shielded
twisted pair (STP) cable (recommended) or other STP cable.
The DTP T EU 332 and DTP T MK 332 are compatible with a DTP HDMI 330 Rx or
DTP DVI 330 Rx receiver, with a range of up to 330 feet (100 meters).
The DTP T EU 232 and DTP T MK 232 are compatible with a DTP HDMI 230 Rx or
DTP DVI 230 Rx receiver, with a range of up to 230 feet (70 meters).
The DTP T EU and DTP T MK units are controlled by Simple Instruction Set (SIS) commands
(see Simple Instruction Set Control on page 19) and the Extron Product Configuration
Software (see Product Configuration Software on page 26).
The switchers fit into EU or MK two‑gang junction boxes or European cable channel
systems, depending on the transmitter model.
The included external 12 VDC power supply accepts 100 to 240 VAC, 50‑60 Hz. A single
power supply connected to either the transmitter or the compatible receiver can power both
units through the STP cable.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Introduction 2
POWER
12V
2
--A MAX
Rx GTx RxTxG
RS-232 IR
RxTx
1
RGB, Y, R-Y, B-Y HDMI HDMI
SIG LINK
DTP OUT
AUDIO
CONTACTRS-232TALLY
3
123G 123+V
RESET
INPUTS
OVER DTPREMOTE
50-60 Hz
100-240V ~
2.0 A MAX
1
L
R
SIG LINK
OUT
SIG LINK
OUT
1
3
4
4
XTP
RS-232 IR
Tx Rx
RTSCTS
GTxRxG Tx Rx G
RS-232 IR
Tx Rx Tx RxG
Tx Rx G
Tx Rx Tx Rx
XTP
RESET
S/PDIF
OUT
DTP
XTP
DTP
XTP
DTP
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
LAN 2
LAN 1
LAN 3
HDBT
G
DTP
HDBT
2
1234
5
7
8
6
DTP CROSSPOINT 84
4
CLASS 2 WIRING
8/
R
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
REMOTE
SIG LINK
IN
SIG LINK
IN
AUDIO INPUTS
AUDIO OUTPUTS
AMP OUTPUT
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
S
DMP EXPANSION
SGG
1
1
2
2
C34C
INPUTS
-S G+S+V
PWR OUT = 6W
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
IR/SERIAL eBUSRELAYS
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
DTP HDMI 330 Rx
OVER DTP
RS-232
IR
Tx Rx Tx RxG
DTP HDMI 230 Rx
OVER DTP
RS-232
IR
Tx Rx Tx RxG
Extron Extron
Help
System
Off
Display
Room
Control
Off
Mute
Screen
Lighting
December 15, 2013 - 7:58 AM
Audio
Control
Volume
Mute
Tuner
1 2 3
VCRLaptop PC DVD
Doc
Cam
Tuner
On
Channel
Last
Presets
More
Presets
321
654
987
Enter
0
HDMI IN
PWRHDCPHDMI VGA AUTO
VGA IN
DTP T EU 332
AUDIO IN AUDIO IN
HDMI IN
PWRHDCP HDMI VGA AUTO
VGA IN
DTP T EU 332
AUDIO IN AUDIO IN
Extron
DTP T EU 332
Two Input DTP Transmitter
for EU-type Junction Boxes
Display
Extron
DTP HDMI
330 Rx
Receiver
RS-232 HDMI
Display
RS-232 HDMI
CATx Cable
up to 330'
(100 m)
CATx Cable
up to 330'
(100 m)
CATx Cable
up to 230'
(70 m)
CATx Cable
up to 330'
(100 m)
Extron
DTP HDMI
230 Rx
Receiver
Ethernet
Ethernet
AudioAudio
Extron
DTP T USW 333
Transmitter
Inputs
Outputs
AV
Control
Network
Microphones
Extron
DTP CrossPoint 84 IPCP SA
Scaling Presentation Matrix Switcher
with DTP Extension and Control Processor
Extron
SM 26
Surface Mount
Speakers
Extron
TLP Pro 1020T
10" Tabletop TouchLink
Pro Touchpanel
Figure 1. Typical Transmitter and Receiver Application
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Introduction 3
Features
Transmits HDMI or analog video, control, and analog audio up to
330 feet (100 meters) (DTP T EU 332 or DTP T MK 332)or 230 feet (70 meters)
(DTP T EU 232 or DTP T MK 232) over a single STP cable — The units provide
high reliability and maximum performance on an economical and easily installed cable
infrastructure.
HDBaseT compatible The DTP output can be configured to send video and
embedded audio, plus bidirectional RS‑232 and IR signals to an HDBaseT‑enabled
display.
Supports computer video to 1920x1200, including HDTV 1080p/60 Deep Color
and 2K
Analog stereo audio embedding — Analog stereo audio signals can be selectively
embedded onto the digital video output signal and transported over DTP/HDBaseT. The
HDMI inputs can be set to pass the embedded digital audio, embed the analog audio,
or to automatically embed the analog audio when no digital audio is detected.
Accepts additional analog stereo audio signals — The DTP transmitters support
a direct pass through connection for stereo analog audio signals for simultaneous
transmission over the same single twisted pair cable. A DTP 330 or DTP 230 receiver
can output balanced and unbalanced audio, allowing streamlined integration within an
AV system.
Bidirectional RS-232 and IR insertion for AV device control — Control and IR
signals can be transmitted alongside the video signal over DTP connections, allowing
the remote device to be controlled without the need for additional cabling. Bidirectional
control insertion eliminates the need for control system wiring to remote devices.
Remote powering of transmitter or receiver — For simplified installation, only one
power supply is necessary to power both devices.
Digital conversion of analog input signals — Analog signals are digitized, ensuring
that a reliable, high quality digital video signal is sent to the output destination.
EDID Minder — Automatically manages EDID communication between connected
devices, ensuring that all sources power up properly and reliably output content for
display.
Compatible with all DTP HDMI 330 (230) and DTP DVI 330 (230) receivers, and
DTP 330- (230-)enabled products — The switching transmitters can be used with
the Extron IN1608, DTP CrossPoint 84, and other DTP 330‑ (230‑) enabled products to
meet application requirements.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 4
Installation and
Operation
This section contains information for mounting, connecting, wiring, and operating the
DTP T EU 332, DTP T MK 332, DTP T EU 232, and DTP T MK 232 . Topics in this section
include:
Installation Overview
Installing the Junction Box or European Cable Channel System
Rear Panel and Side Panel Features
Mounting the Switching Transmitters
Front Panel Connectors
Connection and Wiring Details
Operation
Troubleshooting — If No Image Appears
Installation Overview
All models can mount into junction boxes. The DTP T EU 332 and DTP T EU 232 can mount
into a European cable channel system (also known as a “trunking system”).
For junction boxes, the DTP T EU 332 and DTP T EU 232 mount into European junction
boxes and the DTP T MK 332 and DTP T MK 232 mount into MK junction boxes.
To mount and connect the transmitters, consider the following:
Ensure there is enough space between the rear panel and the back of the junction box
or European cable channel system to fit connectors. The switchers require a minimum
depth of 36 mm (1.4 inch).
NOTE: The depth of the junction box or European cable channel system can vary.
If you are using a European cable channel system with a DTP T EU 332 or DTP T EU 232,
ensure the transmitter fits in the desired channel. Figure 2, on the next page, shows the
dimensions of both EU transmitter models. The depth of all four transmitters is the same.
If necessary, prepare the mounting surface.
CAUTION: Failure to check the items listed below may result in personal injury or
property damage.
ATTENTION : La non‑vérification des éléments listés ci‑dessous peut provoquer
des blessures ou dommages matériels.
Ensure there are no utility cables or pipes at the intended location that might be
damaged or cause injury when installing the device.
Check that the installation meets the building, electrical, and safety codes.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 5
108.80 mm
(4.28")
Top
80.50 mm
(3.17")
151.50 mm
(5.97")
Front
13.50 mm
(0.53")
29.4 mm
(1.16")
48.8 mm
(1.92")
Side
HDMI IN
PWR HDCP HDMI VGA AUTO
VGA IN
DTP T EU 232
AUDIO IN AUDIO IN
DTP
HDBT
RESET
CONFIG
Figure 2. DTP T EU 332 and DTP T EU 232 Dimensions
Choose a location that allows cable runs without interference.
NOTE: Cables may need to be installed in the wall or conduits before installation.
Install the junction box or European cable channel system (see Installing the Junction
Box or European Cable Channel System on the next page).
NOTE: Refer to the manufacturer for more junction box installation requirements.
Route and connect cables to the rear panel connectors (see Rear Panel and Side
Panel Features on page 7).
Mount the unit into the junction box (see Mounting the Switching Transmitters on
page 9).
Connect inputs to the front panel connectors (see Front Panel Connectors on
page 10).
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 6
Installing the Junction Box or European Cable Channel System
Refer to the junction box or European cable channel system manufacturer for additional
installation considerations. If required to cut an opening in the mounting surface, consider
the following:
For accuracy, use a template or the mounting enclosure to mark cut guidelines.
To avoid making the hole too big, cut inside the marked guidelines.
CAUTION: Smooth the edges of the opening to avoid personal injury during
installation and damage to the mounting device or the cables.
ATTENTION : Limez les bords de l’ouverture afin d’éviter toute blessure lors de
l’installation et d’endommager l’appareil de montage ou les câbles.
Secure cables with clamps or ties to provide strain relief.
Trim back and insulate shields with heat shrink.
ATTENTION:
To prevent short circuits, the outer foil shield can be cut back to the point
where the cable exits the cable clamp. Both braided and foil shields should be
connected to an equipment ground at the other end of the cable.
Afin d’éviter les court circuits, le blindage en aluminium extérieur peut être
réduit jusqu’à ce que le câble sorte de la cosse de câble. Le blindage tressé et
le blindage en aluminium devraient être connectés à la masse d’un équipement
à l’autre bout du câble.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 7
Rear Panel and Side Panel Features
Top
Side Rear
DTP
HDBT
RESET
CONFIG
1.0 A MAX
SIGLINK
OUT
Tx Rx GTxRxGTx Rx
RS-232
OVER TP
RS-232
POWER
12V
IR
REMOTE
B
A
C
G
FED
Figure 3. Rear Panel and Side Panel Features
A
TP function switch (see below)
E
Remote RS-232 port (see page 8)
B
Configuration port (see below)
F
Power connector (see page 8)
C
TP connector (see page 8)
G
Reset button (see page 8)
D
Over TP RS-232 and IR port port (see page 8)
A
TP function switch — If the receiving device is in the Extron DTP series, set this
HDTP
DTP
switch to the DTP position. For an HDBaseT‑enabled receiver type, set this switch
to the HDBT position. This switch tailors the output signal as follows:
ATTENTION:
Position this switch BEFORE connecting the appropriate device to the TP
connector. Failure to comply can damage the endpoint.
Positionnez le sélecteur AVANT de connecter l’appareil approprié au
connecteur TP. Ne pas respecter cette procédure pourrait endommager le
point de connexion.
HDBT position — The TP output consists of HDMI with embedded audio plus RS‑232
and IR.
DTP position — TP output consists of HDMI with embedded audio, analog audio,
RS‑232 and IR, and remote power.
NOTES:
When the switch is in the HDBT position, the transmitter and receiver each
requires a local 12 VDC power supply.
When the switch is in the DTP position, one 12 VDC power supply,
connected to either the transmitter or the receiver, can power both units.
B
Config port — Connect a host device to the USB mini B configuration port.
CONFIG
NOTE: A Configuration port connection and a Remote RS‑232 port connection can
both be active at the same time. If commands are sent simultaneously to both, the
command that reaches the processor first is handled first.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 8
C
TP connector — Plug one end of a STP cable to this RJ‑45 female jack
LINK SIG
OUT
on the switching transmitter. Plug the opposite end of this cable into the
DTP Input RJ‑45 connector on a compatible receiver (see TP Cable
Termination and Recommendations on page 13 to properly wire the
RJ‑45 connector and for detailed NOTES).
Signal LED indicator — Lights green when the transmitter outputs a video signal or a
test pattern.
Link LED indicator — Lights yellow when a device is connected and communication
is established.
ATTENTION:
Do not connect this connector to a computer data or telecommunications
network.
Ne connectez pas ces port à des données informatiques ou à un réseau de
télécommunications.
D
Over TP RS-232 and IR port — Plug a serial RS‑232 signal, a
RxTx RxTxG
RS-232 IR
modulated IR signal (up to 40 kHz), or both into this 3.5 mm, 5‑pole direct
insertion connector for bidirectional RS‑232 and IR communication (see IR
and RS-232 Connector Wiring on page 14 to wire the connector).
RS‑232 and IR data can be transmitted simultaneously.
E
Remote RS-232 port — Plug a host device into the switching transmitter
via the 3.5 mm, 3‑pole direct insertion connector for remote control of
the transmitter (see IR and RS-232 Connector Wiring on page 14 to
wire the connector).
9600 Baud 8 data bits
No parity 1 stop bit
F
Power connector — Plug the included external 12 VDC power supply into
1.0 A M
A
POWE
R
12V
this 2‑pole direct insertion connector . To wire the connector, see Power
Supply Wiring on page 15. Alternately, when the TP function switch is in the
DTP position and connected to a compatible DTP receiver it can be powered
through the receiver (see the DTP HDMI 330 User Guide or DTP HDMI 230
User Guide, available at www.extron.com).
NOTE:
When the TP function switch (item
A
on page 7) is in the DTP position,
one power supply can power both units.
When the TP function switch is in the HDBT position, the transmitter and
receiver each requires a local 12 VDC power supply.
G
Reset button — The Reset button initiates a reset of the switcher
(see Reset on page 17 for details).
GRxTx
RS-232
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 9
Mounting the Switching Transmitters
1. Install the mounting plate with the flanged edges pointing away from the junction box.
For EU junction boxes, use four long screws to attach the mounting plate to the
junction box (see figure 4).
Wall Box
Mounting Plate
Figure 4. Mounting Plate Installation for the DTP T EU Units
For MK junction boxes, use two long screws to attach the mounting plate to the
junction box (see figure 5).
Wall Box
Mounting Plate
Figure 5. Mounting Plate Installation for the DTP T MK Units
To install the adapter plate to a European cable channel system, refer to the
manufacturer of the European cable channel system for any additional equipment or
installation requirements.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 10
2. Using the four short screws, attach the transmitter to the flanged edges of the mounting
plate (see figure 6).
W
all Box
Mounting
Plate
HDMI IN
PWR HDCP HDMI VGA AUTO
VGA IN
AUDIO IN AUDIO IN
DTP T EU 232
Figure 6. Transmitter Installation (EU Unit Shown)
Front Panel Connectors
HDMI IN
PWR HDCP HDMI VGA AUTO
VGA IN
DTP T EU 332
AUDIO IN AUDIO IN
BC CA
Figure 7. Front Panel Connectors (DTP T EU 322 Shown)
A
HDMI input port (see below)
C
Audio In connectors (see page 11)
B
Analog video input port (see below)
NOTE: All transmitter models in this guide have a similar front panel appearance.
A
HDMI input port — Connect a digital video source into the switching
HDMI
transmitter via this HDMI connector. It can accept an HDMI or DVI (with an
appropriate adapter) video source.
NOTES:
The maximum HDMI cable length is 4.5 meters (15 feet).
Use an Extron LockIt HDMI Cable Lacing Bracket to secure the HDMI
connector to the device (see HDMI connector on page 12).
B
Analog video input port — Connect an analog video source (RGB
RGB
and component) into the switching transmitter via this 15‑pin HD
connector. See VGA Connector Wiring on page 13 to for connector
pinout.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 11
C
Audio In connectorsIf desired, plug analog audio sources into the
A
UDIO
switching transmitter via these 3.5 mm tip‑ring‑sleeve (TRS) jacks (see figure 7).
NOTES:
The analog audio input on this connector is in addition to the digital audio that
may be embedded in the HDMI inputs.
See figure 8 to identify the connector tip, ring, and sleeve when you are making
connections for the switching transmitter from existing audio cables. A mono
audio connector consists of the tip and sleeve. A stereo audio connector
consists of the tip, ring, and sleeve.
Sleeve ( )
Ring (
-
)
Tip (+)
3.5 mm Stereo Plug Connector
(balanced)
Figure 8. Wiring for TRS Connector
The analog audio can be assigned to a specific input or set to be always output
(see Assign analog audio SIS commands on page 22).
By default, audio input is selected automatically (see Assign analog audio SIS
commands on page 22 to manually select audio inputs). When the HDMI input is
selected with automatic audio input selection, the transmitter prioritizes embedded
digital audio. The following table shows the audio format that is sent over the DTP
connection when a specific audio format is not specified.
Selected
Video Input
HDMI Embedded
Audio Present
Analog Audio
Present
Audio Sent Over TP
VGA N/A Yes Analog audio
VGA N/A No No audio
HDMI Yes No HDMI embedded audio
HDMI Yes Yes HDMI embedded audio
HDMI No Yes Analog audio
HDMI No No No audio
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 12
Connection and Wiring Details
HDMI Connector
Use the LockIt Lacing Bracket, supplied with the switcher, to securely fasten HDMI cable to
device. The following instructions describe how to attach one HDMI LockIt Lacing Bracket.
For more stability, attach a second HDMI LockIt Lacing Bracket to the other mounting
screw.
1. Plug the HDMI cable into the panel connection (see figure 9).
HDMI IN
1
2
3
444
555
Figure 9. Installing the LockIt Lacing Bracket
2. Loosen the HDMI connection mounting screw from the panel enough to allow the
LockIt lacing bracket to be placed over it. The screw does not have to be removed.
3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then
tighten the screw to secure the bracket.
ATTENTION:
Do not overtighten the HDMI connector mounting screw. The shield to which it
fastens is very thin and can easily be stripped.
Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel
elle est attachée est très fin et peut facilement être dénudé.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing
bracket as shown.
5. While holding the connector securely against the lacing bracket, use pliers or similar
tools to tighten the tie wrap, then remove any excess length.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 13
VGA Connector Wiring
The 15‑pin HD (VGA) universal analog input port accepts RGB (RGBHV, RGBS, RGsB) and
component video. Figure 10 shows the pinout for each format type on the connector.
Pin RGBHV
1
Red
Green
R-Y
Y
Red return R-Y return
Green return Y return
Blue return B-Y return
NC NC
Blue B-Y
RGBS Component
2
Red
Green
NC
6 Red return
7 Green return
8 Blue return
3 Blue
15
11
15
4, 5
Pin RGBHV RGBS Component
9
10
14
15
11
12
13
NC
Ground
V sync
NC
H sync
NC
Ground
NC
NC
NC NC
C sync
NC NC
NC
NC
NC
NC
NC
NC
NC
Figure 10. VGA Connector
TP Cable Termination and Recommendations
Figure 11 details the TIA/EIA T 568 B wiring standard. Use this standard to terminate the
DTP cable with RJ‑45 connectors.
5
Pin
1
2
3
6
7
8
4
Side
12345678
Insert
Twisted
Pair Wires
Pins:
RJ-45
Connector
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA T
568B
Figure 11. TP Cable Termination
NOTE: Do not use Extron UTP23SF‑4 Enhanced Skew‑Free AV UTP cable or STP201
cable to link the switching transmitter and receiver. The DTP T EU and DTP T MK units
do not work properly with these cables.
Supported cables
The DTP T EU and DTP T MK units are compatible with shielded twisted pair (STP) and
unshielded twisted pair (U/UTP) cable. However, Extron strongly recommends that you use
STP cable to achieve best performance.
ATTENTION:
To ensure FCC Class A and CE compliance, STP cables and STP connectors are
required.
Afin de s’assurer de la compatibilité entre FCC ClasseA et CE, les câbles STP et
les connecteurs STP sont nécessaires.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 14
Cable recommendations
Extron recommends using the following practices to achieve full transmission distances
up to 330 feet (100 meters) (DTP T EU 332 and DTP T MK 332) or 230 feet (70 meters)
(DTP T EU 232 and DTP T MK 232) and reduce transmission errors.
Use the following Extron XTP DTP 24 STP cables and DTP 24 connectors for the best
performance:
XTP DTP 24/1000 Non‑Plenum 1000 feet (305 meters) spool 22‑236‑03
XTP DTP 24P/1000 Plenum 1000 feet (305 meters) spool 22‑235‑03
XTP DTP 24 Plug Package of 10 101‑005‑02
If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid
conductor, STP cable with a minimum bandwidth of 400 MHz.
Terminate cables with shielded connectors to the TIA/EIA‑T568B standard.
Use no more than two pass‑through points, which may include patch points, punch
down connectors, couplers, and power injectors. If these pass‑through points are
required, use CAT 6 or 6a shielded couplers and punch down connectors.
NOTE: When using STP cable in bundles or conduits, consider the following:
Do not exceed 40% fill capacity in conduits.
Do not comb the cable for the first 20 meters, where cables are straightened,
aligned, and secured in tight bundles.
Loosely place cables and limit the use of tie wraps or hook‑and‑loop fasteners.
Separate twisted pair cables from AC power cables.
IR and RS-232 Connector Wiring
Figure 12 shows how to wire the Remote RS‑232 and Over DTP RS‑232 and IR
connectors.
TxRx
RxTx
Gnd
Gnd
IR Device
RS-232 De
vice
Rx
G
Tx RxTxG
RS-232 IR
RxTx
RS-232
V
OVER DTP
REMOTE
Figure 12. IR and RS-232 Connectors Wiring
NOTES:
The IR Tx and Rx line pair and the RS‑232 Tx and Rx line pairs must each cross
once between their connectors and the source or destination.
The length and preparation of exposed wires is important (see the second and third
power connector CAUTIONS on the next page for details).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39

Extron DTP T EU 332 User manual

Category
Video converters
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI