JVC KD-S895 User manual

Category
Car media receivers
Type
User manual
ENGLISH
‰∑¬
SOUND
VOL
VOL
SOURCE
R
F
U
D
ATT
CD RECEIVER KD-S895
INSTRUCTIONS
§”·π–π”
GET0134-001A
[U]
For installation and connections, refer to the separate manual.
°√ÿ≥“¥Ÿ§ŸË¡◊Õ∑’Ë·¬°µË“ßÀ“° „π°“√µ‘¥µ—Èß·≈–°“√‡™◊ËÕ¡µËÕ
CD KD-S895
‡§√◊ËÕ߇≈Ëπ CD KD-S895
Cover001AKD-S895[U]3.p65 12/26/02, 6:06 PM1
2
ENGLISH
IMPORTANT FOR LASER PRODUCTS
Precautions:
1. CLASS 1 LASER PRODUCT
2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure
to beam.
3. CAUTION: Do not open the top cover. There are no user-serviceable parts inside. Leave all
servicing to qualified service personnel.
4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches
to prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.
5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
BEFORE USE
*
For safety....
Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
Stop the car before performing any complicated
operations.
*
Temperature inside the car....
If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
How to reset your unit
While holding SEL (select), press (standby/on/attenuator) for more than 2 seconds.
This will reset the built-in microcomputer.
Notes:
Your preset adjustments—such as preset channels or sound adjustments—will also be erased.
If a disc is in the unit, it will eject when you reset the unit. Be careful not to drop the disc.
SEL (select)
(standby/on/attenuator)
EN02-04KD-S895[U]f.p65 1/8/03, 11:59 AM2
3
ENGLISH
CONTENTS
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
How to reset your unit ............................... 2
How to use the M (MODE) button ............. 3
LOCATION OF THE BUTTONS ............ 4
Control panel ............................................. 4
Remote controller ...................................... 5
Preparing the remote controller ................ 6
BASIC OPERATIONS ....................... 7
Turning on the power ................................ 7
Setting the clock ........................................ 8
RADIO OPERATIONS ...................... 9
Listening to the radio ................................. 9
Storing stations in memory ....................... 10
Tuning in to a preset station ...................... 11
CD OPERATIONS ........................... 12
Playing a CD ............................................. 12
Locating a track or a particular portion
on a CD .................................................. 13
Selecting CD playback modes .................. 14
Playing a CD Text ...................................... 15
Prohibiting disc ejection ............................ 15
MP3 INTRODUCTION ...................... 16
What is MP3? ............................................ 16
How are MP3 files recorded and
played back? .......................................... 16
MP3 OPERATIONS ......................... 18
Playing an MP3 disc ................................. 18
Locating a file or a particular portion
on an MP3 disc ....................................... 19
Selecting MP3 playback modes ................ 21
SOUND ADJUSTMENTS ................... 22
Selecting preset sound modes
(C-EQ: custom equalizer) ....................... 22
Adjusting the sound .................................. 23
OTHER MAIN FUNCTIONS ................ 24
Changing the general settings (PSM) ....... 24
Detaching the control panel ...................... 25
TROUBLESHOOTING ...................... 26
MAINTENANCE ............................. 28
Handling discs ........................................... 28
SPECIFICATIONS ........................... 29
How to use the M (MODE) button
If you press M (MODE), the unit goes into functions mode, then the number buttons and 5/ buttons
work as different function buttons.
Ex.: When number button 2 works as MO (monaural) button.
To use these buttons for original functions again after pressing M (MODE), wait for 5 seconds
without pressing any of these buttons until the functions mode is cleared.
Pressing M (MODE) again also clears the functions mode.
Time countdown indicator
EN02-04KD-S895[U]f.p65 1/8/03, 11:59 AM3
4
ENGLISH
LOCATION OF THE BUTTONS
Control panel
1 (standby/on/attenuator) button
2 SEL (select) button
3 Control dial
4 Display window
5 Loading slot
6 4 /¢ buttons
7 FM/AM button
8 5 (up) button
+10 button
9 0 (eject) button
p (down) button
10 button
q DISP (display) button
Also functions as SSM buttons when pressed
together with M (MODE) button.
w M (MODE) button
Also functions as SSM buttons when pressed
together with DISP (display) button.
e Remote sensor
r MO (monaural) button
t RPT (repeat) button
y RND (random) button
u Number buttons
i E (EQ: equalizer) button
o CD button
; (control panel release) button
Display window
a LOUD (loudness) indicator
s EQ (equalizer) indicator
d CDin indicator
f CD indicator
g FM band indicators (FM1, FM2, FM3)
h AM band indicator
j Tuner reception indicators
MO (monaural), ST (stereo)
k Volume (or audio) level indicator
l (folder) indicator
/ MP3 indicator
z (disc) indicator
x Disc information indicators
TAG (ID3 tag), (folder), (track/file)
c Main display
v RND (random) indicator
b RPT (repeat) indicator
Display window
EN02-04KD-S895[U]f.p65 1/8/03, 11:59 AM4
5
ENGLISH
Remote controllerRemote controller
3 Selects the preset stations while listening
to the radio.
Each time you press the button, the preset
station number increases, and the selected
station is tuned in.
Skips to the first file of the previous folder
while listening to an MP3 disc.
Each time you press the button, you can
move to the previous folder and start playing
the first file.
4 Functions the same as the control dial on the
main unit.
Note:
These buttons do not function for the
preferred setting mode adjustment.
5 Selects the sound mode (C-EQ: custom
equalizer).
Each time you press the button, the sound
mode (C-EQ) changes.
6 Selects the source.
Each time you press the button, the source
changes.
7 Searches for stations while listening to the
radio.
Fast-forwards or reverses the track/file if
pressed and held while listening to a disc.
Skips to the beginning of the next track/file
or goes back to the beginning of the
current (or previous) tracks/files if pressed
briefly while listening to a disc.
1 Turns on the unit if pressed when the unit
is turned off.
Turns off the unit if pressed and held until
“SEE YOU” appears on the display.
Drops the volume level in a moment if
pressed briefly.
Press again to resume the volume.
2 Selects the band while listening to the radio.
Each time you press the button, the band
changes.
Skips to the first file of the next folder while
listening to an MP3 disc.
Each time you press the button, you can
move to the next folder and start playing
the first file.
SOUND
VOL
VOL
SOURCE
R
F
U
D
ATT
EN05-06KD-S895[U]f.p65 1/8/03, 11:59 AM5
6
ENGLISH
3. Return the battery holder.
Insert again the battery holder by pushing it
until you hear a clicking sound.
WARNING:
Store the battery in a place where children
cannot reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
Do not recharge, short, disassemble, or heat the
battery or dispose of it in a fire.
Doing any of these things may cause the battery
to give off heat, crack, or start a fire.
Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off
heat, crack, or start a fire.
When throwing away or saving the battery,
wrap it in tape and insulate; otherwise, the
battery may start to give off heat, crack, or start
a fire.
Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off
heat, crack, or start a fire.
CAUTION:
DO NOT leave the remote controller in a place
(such as dashboards) exposed to direct sunlight
for a long time. Otherwise, it may be damaged.
Preparing the remote controller
Before using the remote controller:
Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.
Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiveness of
the remote controller decreases, replace the
battery.
1. Remove the battery holder.
1) Push out the battery holder in the
direction indicated by the arrow using a
ball point pen or a similar tool.
2) Remove the battery holder.
2. Place the battery.
Slide the battery into the holder with the +
side facing upwards so that the battery
is fixed in the holder.
Remote sensor
Lithium coin
battery (product
number: CR2025)
(back side)
(back side)
EN05-06KD-S895[U]f.p65 1/8/03, 11:59 AM6
7
ENGLISH
BASIC OPERATIONS
4
Adjust the sound as you want. (See
pages 22 and 23.)
To drop the volume in a moment
Press briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
If you turn the control dial, you can also restore
the sound.
To turn off the power
Press and hold for more than one
second.
SEE YOU appears, then the unit turns off.
If you turn off the power while listening to a
disc, disc play will start from where playback
has been stopped previously, next time you
turn on the power.
CAUTION on Volume Setting:
Discs produce very little noise compared with
other sources. If the volume level is adjusted for
the tuner, for example, the speakers may be
damaged by the sudden increase in the output
level. Therefore, lower the volume before playing a
disc and adjust it as required during playback.
Turning on the power
1
Turn on the power.
Note on One-Touch Operation:
When you select a source in step
2
below, the
power automatically comes on. You do not have
to press this button to turn on the power.
2
Select the source.
To operate the tuner (FM or AM),
see pages 9 11.
To play a CD,
see pages 12 15.
To play an MP3 disc,
see pages 16 21.
3
Adjust the volume.
Volume level appears.
To increase the volume
To decrease the volume
Volume (or audio) level indicator
(see page 24)
3
1
2
EN07-08KD-S895[U]f.p65 1/8/03, 11:59 AM7
8
ENGLISH
Setting the clock
1
Press and hold SEL (select) for more
than 2 seconds.
CLOCK H, CLOCK M,
LEVEL, SCROLL, or TAG
DISP appears on the display.
2
Set the hour.
1 Select CLOCK H (hour) if not shown on
the display.
2 Adjust the hour.
12
3
Set the minute.
1 Select CLOCK M (minute).
2 Adjust the minute.
12
4
Finish the setting.
To check the current clock time or change the
display mode
Press DISP (display) repeatedly.
Each time you press the button,
the display changes as follows.
During tuner operation:
During disc operation:
Notes:
While playing a conventional CD, “NO NAME”
appears for the disc title/performer and the track
title.
For indication change while playing a CD Text or
an MP3 disc, see pages 15 and 19.
During power off:
The power turns on and the clock time is
shown for 5 seconds, then the power turns
off.
Frequency
Clock
Elapsed
playing time
Clock
Disc title /
performer
Track title
EN07-08KD-S895[U]f.p65 1/8/03, 11:59 AM8
9
ENGLISH
RADIO OPERATIONS
Listening to the radio
You can use either automatic searching or manual
searching to tune in to a particular station.
Searching a station automatically:
Auto search
1
Select the band (FM 1 – 3, AM).
Each time you press the
button, the band changes as
follows:
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2
Start searching a station.
When a station is received, searching stops.
To stop searching before a station is
received, press the same button you have
pressed for searching.
Searching a station manually:
Manual search
1
Select the band (FM 1 – 3, AM).
Each time you press the
button, the band changes as
follows:
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2
Press and hold ¢ or 4
until “M” (manual) starts flashing on
the display.
Selected band appears.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
FM1 FM2 FM3 AM
FM1 FM2
FM3 AM
CONTINUED ON THE NEXT PAGE
To search stations of
higher frequencies
To search stations of
lower frequencies
EN09-11KD-S895[U]f.p65 1/8/03, 12:00 PM9
10
ENGLISH
3
Tune in to a station you want while
M (manual) is flashing.
If you release your finger from the button,
the manual mode will automatically turns
off after 5 seconds.
If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for FM
and 9 kHz intervals for AM) until you
release the button.
When an FM stereo broadcast is hard to
receive:
1 Press M (MODE) to enter the
functions mode while listening
to an FM stereo broadcast.
2 Press MO (monaural), while
still in the functions mode, so
that the MO indicator lights up
on the display.
Each time you press the
button, the MO indicator lights
up and goes off alternately.
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved.
To tune in to stations of
lower frequencies
To tune in to stations of
higher frequencies
MO (monaural) indicator
Storing stations in memory
You can use one of the following two methods to
store broadcasting stations in memory.
Automatic preset of FM stations: SSM (Strong-
station Sequential Memory)
Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).
1
Select the FM band (FM1 3) you
want to store FM stations into.
Each time you press the
button, the band changes as
follows:
2
Press and hold both buttons for
more than 2 seconds.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number
buttons—No.1 (lowest frequency) to No.6 (highest
frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
“- -SSM- -” appears, then disappears
when automatic preset is over.
FM1 FM2 FM3 AM
EN09-11KD-S895[U]f.p65 1/8/03, 12:00 PM10
11
ENGLISH
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.
Ex.: Storing FM station of 88.3 MHz into the
preset number 1 of the FM1 band.
1
Select the band (FM1 3, AM) you
want to store stations into (in this
example, FM1).
Each time you press the
button, the band changes as
follows:
2
Tune in to a station (in this example,
of 88.3 MHz).
3
Press and hold the number button
(in this example, 1) for more than
2 seconds.
4
Repeat the above procedure to store
other stations into other preset
numbers.
To tune in to stations of
lower frequencies
To tune in to stations of
higher frequencies
FM1 FM2 FM3 AM
P1 flashes for a few seconds.
Notes:
A previously preset station is erased when a new
station is stored in the same preset number.
Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.
Tuning in to a preset station
You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see Storing
stations in memory on pages 10 and 11.
1
Select the band (FM1 3, AM).
Each time you press the
button, the band changes as
follows:
2
Select the number (1 6) for the
preset station you want.
Note:
You can also use the 5 (up) or (down) button on
the unit to select the next or previous preset stations.
Each time you press the 5 (up) or (down) button,
the next or previous preset station is tuned in.
FM1 FM2 FM3 AM
EN09-11KD-S895[U]f.p65 1/8/03, 12:00 PM11
12
ENGLISH
Refer to “MP3 OPERATIONS” on pages 18 to 21
for operating MP3 discs.
Playing a CD
Insert a CD into the loading slot.
The unit turns on, draws
the CD and starts
playback automatically.
Note on One-Touch Operation:
When a CD is alr eady in the loading slot, pressing CD
tur ns on the unit and star ts pla yback automa ticall y.
CD OPERATIONS
All tracks will be played repeatedly until you stop
playback.
Note:
When a CD is inserted upside down, “EJECT” and
the CD–in indicator flash on the display and the CD
automatically ejects.
To stop play and eject the CD
Press 0.
CD play stops and the CD automatically ejects
from the loading slot. The source changes to the
tuner (you will hear the last received station.)
If you change the source, CD play also stops
(without ejecting the CD).
Next time you select “CD” as the source, CD
play starts from where playback has been
stopped previously.
Notes:
If the ejected disc is not removed for about
15 seconds, the disc is automatically inserted again
into the loading slot to protect it from dust.
(Disc play will not start this time.)
You can eject the disc even when the unit is turned
off.
If the disc is a CD Text, disc title/performer and
then track title will automatically appear.
Elapsed playing time Current track
Total track number
of the inserted disc
Total playing time
of the inserted disc
The CD–in indicator lights up.
The CD–in indicator flashes.
EN12-15KD-S895[U]f.p65 1/8/03, 12:00 PM12
13
ENGLISH
Locating a track or a
particular portion on a CD
To fast-forward or reverse the track
To go to the next or previous tracks
To go to a particular track directly
Press the number button corresponding to the
track number to start its playback.
To select a track number from 1 6:
Press 1 (7) 6 (12) briefly.
To select a track number from 7 12:
Press and hold 1 (7) 6 (12) for more than one
second.
Press and hold ¢ ,
while playing a CD, to fast-
forward the track.
Press and hold 4 ,
while playing a CD, to
reverse the track.
Press ¢ briefly, while
playing a CD, to go ahead
to the beginning of the next
track.
Each time you press the
button consecutively, the
beginning of the next tracks
is located and played back.
Press 4 briefly, while playing a CD, to go
back to the beginning of the current track.
Each time you press the button consecutively,
the beginning of the previous tracks is located
and played back.
To go to a track quickly (+10 and –10 buttons)
1 Press M (MODE) to enter the functions mode
while playing a CD.
2 Press +10 or 10.
* The first time you press +10 or 10 button,
the track skips to the nearest higher or
lower track with a track number of multiple
ten (ex. 10th, 20th, 30th).
Then each time you press the button, you can
skip 10 tracks (see How to use the +10 and
10 buttons below).
After the last track, the first track will be
selected, and vice versa.
How to use the +10 and –10 buttons
Ex. 1: To select track number 32 while
playing track number 6
Ex. 2: To select track number 8 while playing
track number 36
To skip 10 tracks* forwards
to the last track
To skip 10 tracks* backwards
to the first track
(Three times) (Twice)
Track 6 \ 10 \ 20 \ 30 \ 31 \ 32
Track 36 \ 30 \ 20 \ 10 \ 9 \ 8
(Three times) (Twice)
EN12-15KD-S895[U]f.p65 1/8/03, 12:00 PM13
14
ENGLISH
Selecting CD playback modes
To play back tracks at random
(Disc Random Play)
You can play back all tracks on the CD at random.
1 Press M (MODE) to enter the
functions mode while playing a
CD.
2 Press RND (random), while
still in the functions mode, so
that DISC RND appears on
the display.
Each time you press the
button, disc random play mode
turns on and off alternately.
When disc random play is turned on, the and
RND indicators light up on the display. A track
randomly selected starts playing.
To play back tracks repeatedly
(Track Repeat Play)
You can play back the current track repeatedly.
1 Press M (MODE) to enter the
functions mode while playing a
CD.
2 Press RPT (repeat), while still
in the functions mode, so that
TRK RPT appears on the
display.
Each time you press the
button, track repeat play mode
turns on and off alternately.
When track repeat play is turned on, the RPT
indicator lights up on the display. The current
track starts playing repeatedly.
RND indicator
RPT indicator
(disc) indicator
EN12-15KD-S895[U]f.p65 1/8/03, 12:01 PM14
15
ENGLISH
Prohibiting disc ejection
You can prohibit disc ejection and can lock a disc
in the loading slot.
While pressing CD, press and hold 0 for
more than 2 seconds.
EJECT flashes on the display for about
5 seconds, and the disc is locked and cannot be
ejected.
To cancel the prohibition and unlock the disc
While pressing CD, press and hold 0 again for
more than 2 seconds.
EJECT and the CDin indicator flash on the
display, and the disc ejects from the loading slot.
Playing a CD Text
In a CD Text, some information about the disc (its
disc title, performer, and track title) is recorded.
This CD Text information will be shown
automatically when you play a CD Text.
To change the CD Text information
manually, select text display mode while
playing a CD Text.
Each time you press the
button, the display changes as
follows:
Notes:
The display shows up to 8 characters at a time and
scrolls if there are more than 8 characters.
See also To select the scroll modeSCROLL on
page 24.
Some characters or symbols will not be shown (and
be blanked) on the display.
(Ex. ABCå!d# ]ABCA D )
When you press DISP (display) while playing a
conventional CD, NO NAME appears for the
disc title/performer and the track title.
The CDin indicator flashes.
Disc Title / performer
Track title
( lights up on the display)
Elapsed playing time and
Current track number
Clock and
Current track number
EN12-15KD-S895[U]f.p65 1/8/03, 12:01 PM15
16
ENGLISH
MP3 INTRODUCTION
Precautions when recording MP3 files
on a CD-R or CD-RW
This unit can only read MP3 files that are
recorded in the format that is compliant with ISO
9660 Level 1, Level 2, or Joliet.
How are MP3 files recorded
and played back?
MP3 “files (tracks) can be recorded in “folders”—
in PC terminology.
During recording, the files and folders can be
arranged in a way similar to arranging files and
folders of computer data.
Root is similar to the root of a tree. Every file
and folder can be linked to and be accessed from
the root.
Playback order, file search order, and folder
search order of the MP3 files recorded on a disc
are determined by the writing (or encoding)
application; therefore, playback order may be
different from the one you have intended while
recording the folders and the files.
The illustration on the next page shows an
example of how MP3 files are recorded on a
CD-R or CD-RW, how they are played back, and
how they are searched for on this unit.
Notes:
The unit can read a CD-ROM containing MP3 files.
However, if non-MP3 files are recorded together
with MP3 files, this unit will take a longer time to
scan the disc. It may also cause the unit to
malfunction.
The unit cannot read or play an MP3 file without
the extension code—mp3.
This player is not compatible with the data encoded
with Layer 1 and Layer 2 formats.
The unit is not compatible with Playlist**.
**A playlist is a simple text file, used on a PC, which
enables users to make their own playback order
without physically rearranging the files.
What is MP3?
MP3 is an abbreviation of Motion Picture Experts
Group (or MPEG) Audio Layer 3. MP3 is simply a
file format with a data compression ratio of 1:10
(128 Kbps*). That means, by using MP3 format,
one CD-R or CD-RW can contain 10 times as
much data volume as a regular CD can.
* Bit rate is the average number of bits that one
second of audio data will consume. The unit
used is Kbps (1024 bits/second). To get a better
audio quality, choose a higher bit rate. The
most popular bit rate for encoding is 128 Kbps.
This unit is incorporated with an MP3 decoder.
You can play back MP3 files (tracks) recorded on
CD-Rs, CD-RWs, and CD-ROMs.
Compatible with ID3v1 (Version 1)
Extra information data such as album title,
performer name, song title, recording year, music
genre and a brief comment can be stored within
an MP3 file.
This unit can show ID3v1 (Version 1) tags (album
name, performer name, and song title) on the
display. (See page 19.)
Some characters cannot be shown correctly.
This unit is not compatible with ID3v2
(Version 2).
Other main features in this unit:
Maximum number of folders/files:
289 (Total)
Available characters for folder/file names:
A–Z, 0–9, _ (underscore)
Maximum number of characters for file name
(ISO 9660 Level 1): 12 (inclusive of
separation mark—“.
and extension code
—“mp3”)
(ISO 9660 Level 2): 31 (inclusive of
separation mark—“.
and extension code
—“mp3”)
(Joliet): 64 (inclusive of
separation mark—“.
and extension code
—“mp3”)
Maximum number of characters for folder
name: 64
EN16-21KD-S895[U]f.p65 1/8/03, 12:01 PM16
17
ENGLISH
MP3 folder/file configuration
: Root
: Folders
: MP3 files
MP3 playback/search order
The numbers in circles below the MP3 files ( ) indicate the playback order and search order of
the MP3 files. Normally this unit plays back MP3 files in the recorded order.
The numbers inside the folders indicate the playback order and search order of the folders on an
MP3 disc. Normally this unit plays back MP3 files in the folders in the recorded order.
Note:
There is no limit on the number of the hierarchy levels (nested folders). However, up to 8 hierarchy levels is
recommended for stable operations.
1312
18
19
17
2322 24
1110 2120
1 2
5 6
3 4
02
04
ROOT
15 1614
06 07
05 09
01
08
7
8
9
03
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Hierarchy
ROOT
01
EN16-21KD-S895[U]f.p65 1/8/03, 12:01 PM17
18
ENGLISH
Refer also to CD OPERATIONS on pages
12 to 15.
Playing an MP3 disc
Insert an MP3 disc into the loading slot.
The unit turns on, draws
the MP3 disc and starts
playback automatically.
Note on One-Touch Operation:
When a disc is already in the loading slot, pressing CD
turns on the unit and starts playback automatically.
MP3 OPERATIONS
All files will be played repeatedly until you stop
playback.
Notes:
MP3 discs require a longer readout time.
(It differs due to the complexity of the folder/file
configuration.)
When playback starts, folder and file names (or ID3
tags) will automatically appears. (See also page 19.)
If you change the source or turn the power off, disc
playback stops (without ejecting the disc).
Next time you select the CD player as the source or
turn the power on, disc playback starts from where
playback has been stopped previously.
To stop play and eject the disc
Press 0.
Playback stops and the disc automatically ejects
from the loading slot.
Ex.: When the disc contains 19 folders and
144 MP3 files
The CDin indicator flashes.
The CDin indicator lights up.
Total file numberTotal folder number
MP3 indicator lights up.
EN16-21KD-S895[U]f.p65 1/8/03, 12:01 PM18
19
ENGLISH
To change the display information
While playing back an MP3 file, you can change
the MP3 disc information shown on the display.
Each time you press DISP
(display), the display changes to
show the following:
When “TAG DISP” is set to “TAG ON”
(initial setting: see page 24)
* If an MP3 file does not have ID3 tags, folder
name and file name appear. In this case, the
TAG indicator will not light up on the display.
When “TAG DISP” is set to “TAG OFF”
Note:
The display shows up to 8 characters at a time and
scrolls if there are more than 8 characters.
See also To select the scroll modeSCROLL on
page 24.
Locating a file or a particular
portion on an MP3 disc
For MP3 playback/search order see page 17.
To fast-forward or reverse the file
To skip to the next or previous files
To go to a particular file quickly within the
current folder (+10 and –10 buttons)
1 Press M (MODE) to enter the functions mode
while playing an MP3 disc.
Press and hold 4
while playing an MP3 disc,
to reverse the file.
Press and hold ¢
while playing an MP3 disc,
to fast-forward the file.
CONTINUED ON THE NEXT PAGE
Press ¢ briefly while
playing, to skip ahead to
the beginning of the next
file.
Each time you press the
button consecutively, the
beginning of the next files
is located and played back.
Press 4 briefly, while playing, to skip back
to the beginning of the current file.
Each time you press the button consecutively,
the beginning of the previous files is located and
played back.
Album name / performer
(folder name*)
(TAG lights up on the display)
Track title (file name*)
(TAG lights up on the display)
Elapsed playing time and
Current file number
Clock and
Current file number
Folder name
( lights up on the display)
File name
( lights up on the display)
Elapsed playing time and
Current file number
Clock and
Current file number
EN16-21KD-S895[U]f.p65 1/8/03, 12:01 PM19
20
ENGLISH
2 Press +10 or 10.
* The first time you press +10 or 10 button,
the file skips to the nearest higher or lower
file with a file number of multiple ten (ex.
10th, 20th, 30th).
Then each time you press the button, you can
skip 10 files (see How to use the +10 and
10 buttons below).
After the last file, the first file will be
selected, and vice versa.
How to use the +10 and 10 buttons
Ex. 1: To select file number 32 while
playing file number 6
Ex. 2 : To select file number 8 while playing
file number 36
To go to a particular folder directly
IMPORTANT:
To directly select the folders using the number
button(s), it is required that folders are
assigned 2 digit numbers at the beginning of
their folder names. (This can only be done
during the recording of CD-Rs or CD-RWs.)
Ex.: If folder name is 01 ABC
= Press 1 to go to Folder 01 ABC.
If folder name is 1 ABC, pressing 1
does not work.
If folder name is 12 ABC
= Press and hold 6 (12) to go to Folder
12 ABC.
To skip 10 files* forwards
to the last file
To skip 10 files* backwards
to the first file
File 36 \ 30 \ 20 \ 10 \ 9 \ 8
(Three times) (Twice)
(Three times) (Twice)
File 6 \ 10 \ 20 \ 30 \ 31 \ 32
Press the number button corresponding to the
folder number to start playing the first file in the
selected folder.
To select a folder number from 01 06:
Press 1 (7) 6 (12) briefly.
To select a folder number from 07 12:
Press and hold 1 (7) 6 (12) for more than one
second.
Notes:
If MP3 flashes on the display after you have
selected a folder, it means that the folder does not
contain any MP3 files.
You cannot directly select a folder with a number
greater than 12.
To select a particular file in a folder, press
¢ or 4 after selecting the folder.
To skip to the next or previous folder
Note:
If the folder does not contain any MP3 files, it is
skipped.
Press 5 (up) while playing an
MP3 disc to skip to the next
folder.
Each time you press the button
consecutively, the next folder is
located (and the first file in the
folder starts playing, if
recorded).
Press (down) while playing an MP3 disc to
skip back to the previous folder.
Each time you press the button consecutively,
the previous folder is located (and the first file in
the folder starts playing, if recorded).
EN16-21KD-S895[U]f.p65 1/8/03, 12:01 PM20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33

JVC KD-S895 User manual

Category
Car media receivers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI