2. Cudy
  3. GS2018PS2
GS2018PS2

Cudy GS2018PS2 Installation guide

  • Hello! I've reviewed the specification document for the cudy Network Switch GS2018PS2. This device is a 16-port Layer 2 Managed Gigabit PoE+ switch with 2 uplink ports and 2 SFP slots. The document includes detailed information about its configuration options using a DIP switch, along with technical specifications. I am ready to answer your questions about the device.
  • What is the input voltage for this device?
    How many ports are available for PoE?
    What is the maximum working height for this device?
    What is the packet forwarding rate?
Specifications
2
Hardware Connection
1
8K
9.6Kbytes
4096
Multi-mode Fiber: 50/125a62.5/125a100/140um
Single-mode Fiber: 8/125a8.7/125a9/125a10/125um
Operating temperature: -20~50°C
Storage temperature: -40~85°C
Operating Humidity: 10%~90%, No condensation
Storage Humidity: 5%~90%, No condensation
Working height: Up to 10,000 feet
Storage height: Up to 10,000 feet
Model GS2018PS2
AC INPUT
Ethernet Port
Bandwidth
Packet Forwarding rate
DDR SDRAM
Flash Memory
Packet Buffer Memory
Power Socket
Internet
AC100-240Vđ50/60Hz
16 * 10/100/1000Mbps PoE Port
2* 10/100/1000Mbps Uplink Port
2* 1000Mbps SFP Port
1 * RJ45 Console Port
40Gbps
29.76Mpps
128MB
16MB
4M
NVR Monitor
Router
MAC Address
Jumbo frame
VLANs
Fiber Medium
Working Environment
PoE/ACT
LNK/ACT 2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
19 2017 18
2 4 6 8 10 12 14 16 18 20
1 3 5 7 9 11 13 15 17 19
PWR
SYS
SW
Act
Link
Link
Act
16-Port Layer 2 Managed Gigabit PoE+
Switch with 2 Uplink Gigabit Ports and
2 Gigabit SFP Slots
GS2018PS2
Wireless AP Smart VoIP
IP Camera
Powered Device (PD)
SFP Slot
Power input:
AC100-240V Reset Console
Quick Installation Guide
Model: GS2018PS2
EU declaration of conformity
Cudy hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU.The
original EU declaration of conformity may be found at http://www.cudy.com/
LED and Interface Explanation
4
Indicator
PWR(Power Indicator)
SYS(System Indicator)
SW(DIP Indicator)
PoE/ACT
Link/ACT
PWR, SYS, SW, PoE/ACT, Link/ACT
Lighting: Powered
Un-Light: No Power
Flashing: System Start-up
Lighting: System Running
Lighting: VLAN
Un-Light: Default
Flashing: Extend
Lighting: PoE on
Un-Light: PoE off
Lighting: Link connection
Flashing: Data transmission
Un-Light: Link disconnect
DIP Explanation
3
VLAN
Default
Extend
Reset
Email:
support@cudy.com
Website:
www.cudy.com
1-16 ports are isolated from each other, and the PoE Watchdog
function is open (hardware takes precedence over software)
13-16 Port: Supports 250m link extension at a rate of 10M, other ports
normal, PoE Watchdog open (hardware takes precedence over
software)
All ports can communicate with each other, PoE Watchdog is closed
Short press restart, long press 5 seconds to restore factory Settings
/