Cudy GS1028PS2 Installation guide

Type
Installation guide

Cudy GS1028PS2 is a 24-port Gigabit PoE+ switch with 2 Gigabit SFP ports, providing high-speed wired connections for your network devices. It supports IEEE 802.3af/at PoE standards, offering a total power budget of 300W to power IP cameras, VoIP phones, and other PoE-enabled devices. With its VLAN and port isolation features, you can enhance network security and optimize traffic flow. Additionally, the switch features link extension mode, allowing you to extend the transmission distance of PoE devices up to 250 meters.

Cudy GS1028PS2 is a 24-port Gigabit PoE+ switch with 2 Gigabit SFP ports, providing high-speed wired connections for your network devices. It supports IEEE 802.3af/at PoE standards, offering a total power budget of 300W to power IP cameras, VoIP phones, and other PoE-enabled devices. With its VLAN and port isolation features, you can enhance network security and optimize traffic flow. Additionally, the switch features link extension mode, allowing you to extend the transmission distance of PoE devices up to 250 meters.

Specifications
2
Hardware Connection
1
52Gbps
38.7Mpps
Power input: AC100-240V 50/60Hz
Output: 52V5.76A
Power Budget: 300W
Single-Mode Fiber: 850nm, 1310nm
Transmission Distance: 550m/2Km
Single-Mode Fiber: 1310nm, 1550nm
Transmission Distance: 20/40/60/80/100/120km
100,000 hours
410x185x44.5mm
Model
Optical
GS1028PS2
Network Protocol
PoE Standard
POE port output
Power Pin
Network Media
Bandwidth
MAC
Power Socket
Internet
IEEE802.3 / IEEE802.3u / /IEEE802.3x
IEEE802.3ab / IEEE802.3z / IEEE802.3af/at
IEEE802.3af (15.4w) and IEEE802.3at (30W)
DC48-55V
Power over spare pairs 1/2(+) , 3/6 (-)
10BASE-T: Cat3 45 or higher UTP(≤100 meter)
100BASE-TX: Cat5 or UTP (≤100 meter)
1000BASE-TX: Cat5 or UTP (≤100 meter)
8K
4M
NVR Monitor
Router
Packet Buffer Memory
Packet Forwarding Rate
Power Supply
MTBF
Product Dimension
LNK/ACT
1000M
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23 26 25
2 4 6 8 10 12 14 16 18 20 22 24 26
1 3 5 7 9 11 13 15 17 19 21 23 25
PWR 1000M
Act
Act
1000M Extend(17-24)
Default
VLAN(1-24) 24-Port Gigabit PoE+ Switch
with 2 Gigabit SFP Ports
GS1028PS2
Wireless AP Smart VoIP
IP Camera
Powered Device (PD)
SFP Slot
Power input:
AC100-240V
Quick Installation Guide
Model: GS1028PS2
EU declaration of conformity
Cudy hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU.The
original EU declaration of conformity may be found at http://www.cudy.com/
810600098
Email: support@cudy.com
LED and Interface Explanation
4
PWR
1-26 Port
1-26 Port
Power supply indicator
Red
RJ-45 LINK indicator
Green
RJ-45 ACT indicator
Green
ON
OFF
ON
OFF
ON
OFF
Flashing
Powered
No power
1000M Connect
100M or Disconnect
Connecting
Disconnect
Data Transmit
DIP Explanation
3
VLAN
Default
Extend
Port Isolation
Standard Switch
Link Extension
Downlink designated ports are isolated
from each other, only transmit data with
the uplink port.
All ports communicate freely
The specified port speed drops to 10Mbps,
max PoE transmission distance is 250 meters
Email:
support@cudy.com
Website:
www.cudy.com
  • Page 1 1
  • Page 2 2

Cudy GS1028PS2 Installation guide

Type
Installation guide

Cudy GS1028PS2 is a 24-port Gigabit PoE+ switch with 2 Gigabit SFP ports, providing high-speed wired connections for your network devices. It supports IEEE 802.3af/at PoE standards, offering a total power budget of 300W to power IP cameras, VoIP phones, and other PoE-enabled devices. With its VLAN and port isolation features, you can enhance network security and optimize traffic flow. Additionally, the switch features link extension mode, allowing you to extend the transmission distance of PoE devices up to 250 meters.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI